Turnstiles PY300DC Manuel utilisateur

PY300DC
Sliding Gate Opener
User Manual

1
Dear users,
Thank you for choosing this product. Please read this manual carefully before installation and use.
Please do not forget to include this manual if you send the product to a third party.
1. Safety Instruction
Please make sure that the power voltage being used matches with the supply voltage of gate
opener (AC110V or AC220V); kids are not allowed to touch the control devices or the
remote-control unit.
The remote-control unit is single button mode or three button mode (please refer to the instructions
of the remote control in accordance with the actual gate opener type). The indicator light on the
remote-control unit will flicker when its button is pressed. Main engine and gate can be unlocked
with a disengagement wrench and the gate can be manually operated after disengagement.
Please make sure that nobody is around the main engine or gate when the switch is operated.
Please temporarily stop using the product if the main engine needs to be repaired or regulated. The
installation and maintenance of the product must be carried out by professionals.
Please read this manual carefully before installing、using、maintaining or repairing it. Without
following this manual, any injury or property losses caused by improper use or unauthorized
modification is out of the responsibility of our company.

2
2. Packing List (standard)
No.
Picture
Name
Quantity
1
Main engine
1
2
Manual release key
1
3
A
B
C
D
A
B
C
D
Remote control
2
4
Accessories box
1
4-1
Manual release bar
1
4-2
Foundation bolt M8
4
4-3
Nut M8
8
4-4
Flat washer Ø8
4-6
4-5
Spring washer Ø8
4-7

3
2. Packing List (optional)
No.
Picture
Name
Quantity
1
Steel gear rack
1m/pc
2
Nylon gear rack
1m/pc
3
Infrared sensor
1
4
0
8
5 6
97
4
1 2 3
Wireless keypad
1
5
Alarm lamp
1
6
Mounting plate
1
3. Technical parameters
Model
PY300DC
Power supply
220V/50Hz;110V/60Hz
Motor power
100W
Gate Moving speed
13m/min
Maximum weight of gate
300Kg
Remote control distance
≥30m
Remote control mode
Single button mode
Limit switch
Electronic limit switch
Noise
≤60dB
Working duty
S2, 20min
Recording of up remote controls
20
Frequency
433.92 MHz
Working temperature
-20°C ~ +70°C

4
Storage battery
24V 4.5Ah
Package weight
11.32Kg
4. Installation
PY300DC sliding gate opener is applicable to gate weight less than 300kg, and length of the sliding
gate less than 8m. The drive mode adopts the rack and gear transmission. This gate opener must
be installed inside the enclosure or yard for protection.
4.1 Installation drawing
⑤
④
③
②
0
8
5 6
97
4
1 2 3
⑧
①
⑦
⑥
Figure 1
①Gate opener; ②Wireless keypad (optional); ③Gate; ④Infrared sensor (optional);
⑤Alarm lamp (optional); ⑥Safety stop block; ⑦Gear rack; ⑧Remote control;
4.2 Size of main engine and accessories
4.2.1 Size of main engine

5
300
270 200
Figure 2
4.2.2 Size of mounting plate
200±0.2
270
150
100±0.2
4×φ10
Figure 3
4.3 Installation procedures
4.3.1 Preparation work before installation
Please make sure that the sliding gate is correctly installed, the gate rail is horizontal, and the gate
can be manually moved smoothly before installing the gate opener.
Cable installation
In order to guarantee the normal operation of the gate opener and protect the cables from damages,
please bury the motor & power cable and controlling cable separately with two PVC tubes.
Concrete pedestal
Please precast a concrete pedestal with the size can be 400mm x 250mm, depth be 200mm in
advance, so as to firmly install PY300DC gate opener. Please make sure the distance
between the gate and gate opener is appropriate before casting the pedestal.

6
Embedded screws
Concrete
Power line
Mounting plate
Foundation bolt
Figure 4
4.3.2 Main engine installation
a) Dismantle the plastic housing on the main engine before installation and keep relevant fasteners
properly;
b) Please prepare the power line for connecting the mounting plate to the main engine (the number
of power supply cable cores should not be less than 3 PCS, the sectional area of cable core should
be over 1.5mm²and the length should be determined by users according to the situation on
installation spot)
c) Please unlock the main engine before installation, the unlock method is: first remove the upper
cover, and then insert the key to open the shell cover. Insert the manual release bar into the release
hole and clockwise rotation till the output gear can be rotated easily, which means the motor has
been released.
Figure 5
4.3.3 Gear rack installation
Fix the mounting screws to the rack.
Put the rack on the output gear, make the rack engage with the output gear then weld the
mounting screw to the gate (each screw with one solder joints firstly).
Manually move the gate (gate should be moved smoothly after motor unlocked) to check

7
whether there is a fit clearance between rack and output gear, as shown in Figure 7.
Weld all the mounting screws to the gate firmly.
Make sure that all racks on the same straight line.
Pull the gate after installed, make sure the entire trip is flexible without any stuck.
Figure 6
The fit clearance of output gear and rack is shown in Figure 7 below:
1-21-2
GearGear rackrack
OutputOutput geargear
mmmm
Figure 7
Warnings
·To ensure safety, install safety stop blocks on both ends of the rails to prevent the gate from running
out of the rail. Before installing the main engine, make sure that the safety stop blocks are in place
and whether it has the function of preventing the gate from running out of the rail or safety range.
·Please make sure that the main engine and its components have good mechanical properties, and
the gate can be operated flexibly when manually moved before installing the main engine.
·Please note that for this product, one control can only drive one main engine, otherwise, the control
system will be damaged.
·Earth leakage circuit breaker must be installed in where the gate movement can be seen, and the
minimum mounting height is 1.5m to avoid being touched by children.
·After installation, please check whether the mechanical property is good or not, whether gate
movement after manual unlocking is flexible or not, whether the installation for infrared sensor
(optional) is correct and effective.

8
4.3.4 Control board wiring
-LAMPLAMP+
GNDGND
PEPE
+24V+24VCLOSECLOSE STOPSTOP OPENOPEN C OMCOM OSCOSC
COMCOM
InfraredInfrared sensorsensor
24VDC24VDC
AlarmAlarm lamplamp
StopStop buttonbutton
CloseClose buttonbutton
OpenOpen buttonbutton
SingleSingle buttonbutton switchswitch
+SOLARSOLAR BATBAT-+ RECHGRECHG BATBAT-JXPYM01AAJXPYM01AA
2009.07.102009.07.10
J6J6
J5J5
T1T1T2T2
J1J1
C1C1
J5J5
J3J3
J2J2
C5C5
C20C 20 C18C 18
VCCVCC DATADA TA GNDGND GNDGND ANTANT
24VAC24VAC M
24VDC24VDC motormotor HallHall lineline
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
COMCOM
Figure 8
Transformer wiring:
+SOLARSOLAR B ATBAT -+ RECH GR ECHG B ATBA T-JXPYM01AAJXPYM01AA
2009.07.102009.07.10
J6J6
J5J5
T1T1T2T2
J1J1
ControlControl boardboard
TransformerTransformer inputinput 220VAC220VAC
TransformerTransformer outputoutput 24VAC24VAC
Figure 9

9
Control board wiring instruction:
24VDC motor: black wire to “T1”, red wire to “T2”. If the gate opening direction is wrong, please
exchange T1 and T2.
J1: Transformer secondary (AC24V / 3.3A);
J2: Singe button (OSC and COM);
Three button (OPEN, CLOSE, STOP, COM);
J3: Infrared sensor (PE and COM);
Output DC power (24V and GND);
J4: Alarm lamp, voltage 24VDC;
J5: Solar panel and storage battery;
J6: Hall line.
Set open and close positions:
1. Press and hold SET until number “1” is indicated on the LED display.
2. Press and hold OPEN to reach the desired open position (press OPEN button, the door must in
open direction, otherwise exchange the two motor wires).
3. Press the SET to confirm the open position, LED display indicates “2”.
4. Press and hold CLOSE to reach the desired close position.
5. Press the SET to confirm the close position.
6. The door will do a complete open and close cycle.
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
SETSET CODECODE
CLOSECLOSE
OPENOPEN
K1K1 K2K2
K3K3
K4K4
Figure 10
Set automatic close time:
1. Press and hold OPEN until “─” is indicated on the LED display.
2. Press OPEN to increase the automatic close time, press CLOSE to decrease the time.
3. Set time to “0”, the automatic close function will disable.
4. Press SET to confirm the setting.
5. Add 10 seconds per number.
NOTE: Automatic close function is available only when the door is in fully opened position.
Table des matières
Autres manuels Turnstiles ouvre-porte


















