TSS DUR 120 USB Manuel utilisateur
1
DUR 120 USB
and
DUR 120 ETHERNET
Desktop UHF RFID reader
User Guide
Ver. 1.3
04/2016
TSS COMPANY s.r.o., Pod Rovnicami 41, 84104 Bratislava, Slovakia
2
© Copyright 2015, TSS COMPANY, s.r.o.
No part of this manua may be reproduced in any form or by any means, e ectronic,
mechanica , recording, or otherwise, without the prior written permission of TSS COMPANY.
TSS COMPANY reserves the right to modify its product specifications without any further
notice. For up to date information p ease visit www.tsscompany.eu.
The information contained herein has been carefu y checked and is be ieved to be accurate.
However, TSS assumes no responsibi ity for inaccuracies.
3
Contents
1
Introduction ........................................................................................................................ 4
2
Connecting the reader and installing the USB driver ......................................................... 4
3
Ethernet connection (Only DUR 120 ETHERNET) ............................................................... 4
4
Functionality test ................................................................................................................ 4
5
Technical specifications ...................................................................................................... 5
6
TSSTagger ........................................................................................................................... 7
Installation ................................................................................................................... 7
Inventory Tab ............................................................................................................... 8
Read/Write Tab ......................................................................................................... 10
Kill/Lock Tab ............................................................................................................... 12
EPC Tab ...................................................................................................................... 14
Settings Tab ............................................................................................................... 16
Reader Settings .................................................................................................. 17
Inventory ............................................................................................................ 17
Connect Tab ............................................................................................................... 18
Connection Type (a) ........................................................................................... 19
Serial Port Settings (c) ........................................................................................ 19
LAN Settings (f) ................................................................................................... 19
Device Search (j) ................................................................................................. 20
Device Net ork Settings (q) ............................................................................... 21
7
TSSUpdater ....................................................................................................................... 22
Installation ................................................................................................................. 22
Firm are update ....................................................................................................... 22
Troubleshooting......................................................................................................... 26
8
References ........................................................................................................................ 27
9
Revision History ................................................................................................................ 28
Annex 1: Declaration of Conformity......................................................................................... 29
4
1Introduction
The desktop UHF RFID reader DUR 120 a ows so ution deve opers to use app ications that
require desktop reading and writing of EPCg oba UHF C ass 1 Gen 2 tags. The DUR 120 reader
is contro ed by and powered from a host PC or aptop through a USB interface. In case of DUR
120 ETHERNET the ethernet interface can be used for communication purpose.
2Connecting the reader and installing the USB driver
The DUR 120 reader can be connected to a PC or a notebook via a USB interface. When
connecting the device for the first time, the user has to insta the necessary device drivers to
a ow Windows to recognize the reader. The reader emu ates a virtua seria port.
You can down oad VCP drivers for Windows based systems from this website:
http://www.ftdichip.com/Drivers/VCP.htm
You can down oad detai ed driver insta ation guide from this website:
http://www.ftdichip.com/Support/Documents/InstallGuides.htm
3Ethernet connection (Only DUR 120 E HERNE )
A standard ethernet connection with an 8-pin RJ connector using 2 twisted pairs has to
be used to connect DUR 120 ETHERNET. The DUR 120 ETHERNET se ects automatica y
between the USB and ethernet interface based on the first received va id packet after the start
up from USB or ethernet interface. The DUR 120 ETHERNET reader is powered through the
USB connector.
4Functionality test
The user can easi y test the basic functiona ities of the reader with the TSSTagger demo
software. Chapter 6 of this guide contains more information on TSSTagger.
5
5echnical specifications
DUR 120 USB:
Frequency Band: 865 ÷ 868 MHz (ETSI EN 302 208 v. 1.4.1.)
Number Of Channels: 4 (comp iant to ETSI EN 302 208 v. 1.4.1.)
RF Po er Output – e.r.p.: max. 14 dBm
Modulation: DSB-ASK
Antenna Gain: 5 dBic
Antenna Polarization: Integrated circu ar po arized antenna
Air Interface Protocol: EPCg oba UHF C ass 1 Gen 2 Version 2.0.0
Supports tag vendor specific custom commands
Supports NXP UCODE DNA
Tag Communication Rate: 40 kbps
Data Encoding
Interrogator -> Tag:
PIE, 40kHz
Data Encoding
Tag -> Interrogator:
FM0, 40kHz
Tag Read Rate: Up to 50 tags/second
Tag Read Range: Up to 50 cm, depending on tag and environment
(Tested with an ALN-9662 tag)
USB Interface:
USB 2.0 Fu Speed
It appears as USB seria port
USB mini-B connector
User Interface:
Power LED (orange)
Status LED (green)
Operating Temperature: -20 °C do +55 °C
Po er Supply: 5 VDC (Powered by USB interface)
Po er Consumption: max. 200mA
Dimensions: 110mm L x 110mm W x 38mm H
Weight: 240 g
Length Of USB Cable: 1,8m
6
DUR 120 ETHERNET:
Frequency Band: 865 ÷ 868 MHz (ETSI EN 302 208 v. 1.4.1.)
Number Of Channels: 4 (comp iant to ETSI EN 302 208 v. 1.4.1.)
RF Po er Output – e.r.p.: max. 14 dBm
Modulation: DSB-ASK
Antenna Gain: 5 dBic
Antenna Polarization: Integrated circu ar po arized antenna
Air Interface Protocol: EPCg oba UHF C ass 1 Gen 2 Version 2.0.0
Supports tag vendor specific custom commands
Supports NXP UCODE DNA
Tag Communication Rate: 40 kbps
Data Encoding
Interrogator -> Tag:
PIE, 40kHz
Data Encoding
Tag -> Interrogator:
FM0, 40kHz
Tag Read Rate: Up to 50 tags/second
Tag Read Range: Up to 50 cm, depending on tag and environment
(Tested with an ALN-9662 tag)
Ethernet Interface : 10/100 Mbps
TCP/IP protoco s
Supports IP Configuration
- Static, DHCP
Supports DNS
(Defau t configuration is: Static IP Address,
192.168.0.110)
USB Interface:
USB 2.0 Fu Speed
It appears as USB seria port
USB mini-B connector
User Interface:
Power LED (orange)
Status LED (green)
Operating Temperature: -20 °C do +55 °C
Po er Supply: 5 VDC (Powered by USB interface)
Po er Consumption: max. 450 mA
Dimensions: 110mm L x 110mm W x 66mm H
Weight: 290 g
Length Of USB Cable:: 1,8m
7
6TSSTagger
The user interface of TSSTagger is split into five sections, or tabs:
Inventory Tab:
This is the main tab of the application used to connect and disconnect the reader and to
start and stop the HID emulation. This tab also contains the inventory list here EPC
numbers are stored.
Read/Write Tab:
This tab is used to read from and rite to different memory banks of the tag.
Kill/Lock Tab:
This tab is used to adjust lock actions and permissions for different memory banks and
pass ords.
EPC Tab:
This is the application’s EPC editor designed for easy EPC number editing.
Settings Tab:
This tab contains several application settings.
Installation
-Extract the contents of TSSTagger.zip into the program directory.
-Double-click vcredist_x86.exe to start the setup of Microsoft Visual C++ 2013 x86
Redistributable soft are package.
-The setup program guides you through the installation.
-Wait until Microsoft Visual C++ 2013 x86 Redistributable soft are package has been
successfully installed.
8
Inventory Tab
a. Connect reader:
This button serves to connect and disconnect the reader. To ensure the reader
ill connect properly, the user should ait until Windo s USB drivers have
properly installed (this can be confirmed in the lo er right corner of the screen in
the Windo s task bar notification area).
9
b. Clear inventory list:
This button c ears the inventory ist.
c. Inventory list:
This is where read counts of tags and EPC numbers are isted, sorted by time
stamp. The maximum number of tags to be disp ayed in the inventory ist can be
set in the “Settings Tab”. The ist can be c eared using the “Clear inventory list”
button ocated under the inventory ist.
d. Read Single-Tag:
This button a ows the user to read the EPC number of the tag, disp aying it in the
inventory ist.
e. Read Multi-Tag:
This button a ows the user to read the EPC numbers of mu tip e tags.
f. Main log:
The main og shows the connection status, sent and received packets and error
messages re ated to seria port communication. Content of the main og can be
copied and pasted or c eared using the right-c ick context menu.
g. Status Bar:
The status bar shows information about the current y connected device and any
other messages.
10
Read/Write Tab
a. Tag selection:
These radio buttons allo the user to select bet een orking ith the first tag
responding to the reader and the tag specified by the EPC number.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels TSS Système RFID
