TSL Tally Man PSU-22 Manuel utilisateur

UMD PSU-22 1 V4.0

The TSL Tally and

UMD Configuring Program

Power Supply PSU-22

– this section is intended to be read in conjunction with the

Introduction

Television Systems Limited.

Vanwall Road, Maidenhead, Berkshire, SL6 4UB

Telephone +44 (0)1628 676200, FAX +44 (0)1628 676299

UMD PSU-22 2 V4.0

Safety

Installation.

Unless otherwise stated TSL equipment may be installed at any angle or position within an operating

temperature range of 5°~ 25°C .

The RJ45 connectors are for use only with TSL UMD equipment.

All TSL equipment conforms to the EC Low Voltage Directive:

EC Low Voltage Directive (73/23/EEC)(OJ L76 26.3.73)(LVD).

Amendment: (93/68/EEC) (OJ L220 30.8.93).

Earthing/Grounding

In all cases, the frame of the equipment must be earthed on installation. Connection to an earthed strip

running the length of the frame is ideal.

The earth pin on the IEC mains inlet connector is connected to the metal frame of the equipment, to 0

volts on the internal DC PSU and to signal ground, unless otherwise stated. All metal panels are

bonded together. Rack mounted equipment must be earthed (grounded).

Mounting

Careful consideration of the of equipment location and mounting in racks must be made. In particular,

consideration must be given to the stability of free-standing racks by mounting heavy equipment low in

the rack. The rear of the unit should be supported in the rack.

Power

For pluggable equipment, the socket outlet shall be installed near the equipment and shall be easily

accessible.

Consideration must be given to the supply circuit loading and switch on/fault surges that will affect

overcurrent protection trips and switches etc.

Check that the fuse rating is correct for the local power (mains) supply. Replacement fuses must be of

the same rating and type for continued protection against fire risk.

The equipment rating is shown on the rear panel.

No power supply cord is provided with this equipment.

Do not switch on until all connections are made.

Ventilation

Due consideration for cooling requirements must be given when mounting the equipment. Ideally 1RU

of rack space should be left above and below the unit.

If the equipment is installed in a closed unit, consideration must be given to providing forced air cooling

in order that the maximum recommended temperature is not exceeded.

UMD PSU-22 3 V4.0

Warranty, Maintenance And Repair

All TSL equipment is guaranteed for one year from the date of delivery to the customer’s premises. If

the equipment is to be stored for a significant period, please contact TSL concerning a possible

extended warranty period.

Failure during warranty

If this TSL product should fail or become faulty within the warranty period, first please check the IEC

inlet fuses.

All maintenance work must be carried out by trained and competent personnel.

If equipment has to be returned to TSL for repair please observe the following overleaf:

TSL Returns Procedure

Please telephone +44 (0)1628 687200 (Fax: +44 (0)1682 687299) and ask for Sales who will provide

a Returns Number. This will enable us to track the unit effectively and will provide some information

prior to the unit arriving.

For each item, this unique Returns Number must be included with the Fault Report sent with the unit.

A contact name and telephone number are also required with the Fault Report sent with the unit.

Fault report details required.

•Company:

•Name:

•Address:

•Contact Name:

•Telephone No:

•Returns Number:

•Symptoms of the fault (to include switch setting positions, input signals etc):

Packing

Please ensure that the unit is well packed as all mechanical damage is chargeable. TSL recommends

that you insure your equipment for transit damage.

The original packaging, when available, should always be used when returning equipment.

If returned equipment is received in a damaged condition, the damage should be reported both

to TSL and the carrier immediately.

Year 2000 Conformity Requirements

This product conforms to the following rules:

Rule 1 No value for the current date will cause any interruption in operation.

Rule 2 Date based functionality will behave consistently for dates prior to, during and after the

Year 2000.

Rule 3 In all interfaces and data storage, the century in any date is specified either explicitly or

by unambiguous algorithms or by inferencing rules.

Rule 4 The Year 2000 is recognised as a leap year.

UMD PSU-22 4 V4.0

EC DECLARATION OF CONFORMITY

Application of Council Directives Nos:

EC Low Voltage Directive (73/23/EEC)(OJ L76 26.3.73)(LVD).

Amendment: (93/68/EEC) (OJ L220 30.8.93).

Conformity Standards Declared:

BS EN60950

EMC Directive: 89/336/EEC, Amended 92/31/EEC.

Conformity Standards Declared:

EN 50081-1, EN 50082-1

Manufacturer’s Name: Television Systems Ltd

Manufacturer’s Address: Vanwall Rd

Maidenhead

Berks SL6 4UB

Type of Equipment: Under Monitor Display Power Supply Unit

Model No: UMD-PSU-22

Part Number: TSLP- UMD-PSU-22

Date CE Mark Affixed:

I, the undersigned, declare that the equipment specified above conforms to the quoted Directives and

Standards.

Place: Maidenhead, England Signature:

Date: April 2002 Print: J F PINNIGER

Position: PRODUCT MANAGER

UMD PSU-22 5 V4.0

Contents

1.0 Installation

2.0 Description

3.0 Operation

4.0 Connection Details on the Hardware

5.0 Specifications

6.0 The Internal Power Supplies

7.0 General Notes

WARNING

Disconnect power before

removing the covers

There are no user

adjustable parts inside the

unit

UMD PSU-22 6 V4.0

1.0 Installation

Unless otherwise stated TSL equipment may be installed at any angle or position within a

recommended operating temperature range of 5°~ 25°C .

Good installation practice should be adhered to for the cooling requirements of this unit. Ideally, allow

1RU of space between this unit and adjacent units.

For pluggable equipment, the socket outlet should be installed near the equipment and should be

easily accessible.

For continued protection against risk of fire, all components must be replaced with similarly rated

components.

In all cases the case of the equipment should be earthed on installation. A threaded stud is provided

for this purpose.

Do not switch on until all connections are made.

2.0 Description

The PSU-22 is a 19” 2RU unit which provides 240 Watts of power, mnemonic and serial tally

distribution for typically up to a maximum of 96 S8C / D8C displays.

The unit may be ordered or upgraded with a second 240 Watt PSU which will provide 100%

redundancy in the event of an internal power supply module unit failure. This upgrade is a

straightforward plug in upgrade. The frame is fully wired to accept a second PSU.

Single PSU units have the PSU (PSU1) fitted to the LH frame and the top IEC is the power inlet

connector.

This unit can provide a maximum of 96 PLU (power loading units) where one PLU is equivalent to 2.5

Watts. Note that a maximum of 240 Watts only may be drawn from the PSU-22.

In the standard, non dual-redundant unit, power (at +24V) is provided by one auto-ranging PSU (88 ~

264V, 47/63 Hz) via a diode bridge arrangement output (to isolate the second optional PSU module)

and re-settable internal fuse to the rear distribution board.

Each of the 48 RJ45 o/p connectors is rated at a maximum of 1.1Amps*( the re-settable fuse opens at

about 1.5A after approx. 90 secs).

The front LEDs from the top down indicate:

Module A (LH module)

Module B (RH module)

+24VDC Rail

Serial 1 (Green when active, amber when serial data present but not used).

Serial 2 (Green when active, amber when serial data present but not used).

Once an input signal is detected by the unit that signal will continue to be used until it fails or is

intentionally removed. The circuit is noise immune so there will be a short delay before the circuit

switches from one input to the other.

An auxiliary +24V unregulated supply, fused at 1.8 Amps, is available on the rear panel. This power is

included in the overall 240 Watts available from the internal PSU block(s).

*Do not exceed the rating of the unit of 96 PLU or 240 W otherwise an internal, re-settable fuse will

open.

UMD PSU-22 7 V4.0

3.0 Operation

The PSU-22 can be used either:

1. As a stand alone unit. For example, in a monitor stack with dynamic displays or static displays

not requiring serial tally information, but where the silence detection data from Audio

Monitoring Units needs to be passed to an alarm monitoring system such as the TSL AMS-1,

or, more usually.

2. As a single or one of several local power supplies of a larger system where the displays are

controlled by a TallyMan Controller, TM1.

The input RJ45 serial port on the rear of the PSU-22 is fed from any TM1 Display Port which could be

located at some distance away (up to 200m) from the monitor stack.

4.0 Connection Details on the Hardware

4.1 Serial Connections

Input Connections

PIN FUNCTION DIRECTION

1 0V GND

2 0V GND

3 TX- OUT

4 RX+ IN

5 RX- IN

6 TX+ OUT

7 +24V IN

8 +24V IN

The input serial connector(s) is connected to any of the Display Ports on the TallyMan Controller

using a 1:1 RJ45 cable. The pin function of the o/p connector will be the reverse of that shown

above.

Output connectors

PIN FUNCTION DIRECTION

1 0V GND

2 0V GND

3 RX- OUT

4 TX+ IN

5 TX- IN

6 RX+ OUT

7 +24V IN

8 +24V IN

UMD PSU-22 8 V4.0

4.2 RJ45 Cable Connections

View from the back.

Cable entry.

RJ45 Connector on the cable

4.3 Adapter cable to connect RJ45 Displays to a D15 connector on a TSL UMD

RJ45 UMD

FUNCTION

D15M

1 0V 9

2 0V 10

3 TX- 14

4 RX+ 1

5 RX- 2

6 TX+ 13

7 +24V 7

8 +24V 7

4.4 The D25 Connector

This socket carries GPI alarm o/p information. In the good position, the relays are energised. The

table shows the unit in the good position with all modules fitted.

Pin out is as follows:-

Signal names common closed open

PSU MODULE A 14 1 2

PSU MODULE B 3 15 16

POWER BUS 17 4 5

SER1 PRESENT 6 18 19

SER2 PRESENT 20 7 8

SER1 STANDBY 23 10 11

SER2 STANDBY 9 21 22

SERx STANDBY means the signal is present, but other the channel is active.

1 2 3 4 5 6 7 8

UMD PSU-22 9 V4.0

5.0 Specifications

Single internal PSU – top IEC connector. PSU1

Width: 483mm Height: 88mm

Depth: 400mm Weight: 5.5Kgm

Input Power: 280W Operating Temp 5 ~ 25C

Output Power 240W

Twin internal PSUs – both IEC connectors

Width: 483mm Height: 88mm

Depth: 400mm Weight: 6.6Kgm

Input Power: 300W Operating Temp 5 ~ 25C

Output Power 240W

The depth figures do not include connector depth.

»It is suggested that an additional 100mm is allowed for the power IEC connector depth. This

will give enough space to allow removal of the connecter with the unit still in situ.

UMD PSU-22 10 V4.0

6.0 The Internal Power Supplies

These are Mean Well SP-300 Series units. In the event of a failure the faulty item should be returned

to TSL for replacement.

The user should not attempt any repairs as this voids the PSU manufacturer’s warranty.

Manufacturer’s Specification Model SP- 300-24

DC Output Voltage 24V

Output Voltage Tolerance 1%

Output Rated Current 12.5A

Output Current Range 0 – 12.5A

Ripple and Noise 150mV pk-pk

Line Regulation 0.2%

Load Regulation 0.5%

DC Output Power 300W

Efficiency 86%

DC Voltage Adjustment 20 ~ 26.4V

Input Voltage Range 88264VAC 4763Hz; 124~370VDC

AC Current 4A/115V, 2A/230V

Power Factor 0.9/100240VAC

Inrush Current 18A/115V 36A/230V

Leakage Current 1mA/240VAC

Overload Protection 105135% Type: Pulsing Hiccup Shutdown Reset:

Auto Recovery

Over Voltage Protection 27.6-32.4V

Fan Control Over Temp Protect. RTH1 or RTH250C Fan On, 45C Fan Off

70C Output Shutdown

Temp. Coefficient 0.03%/C (050C)

Setup, Rise, Hold up Time 1.5s, 50ms, 20ms

Vibration 10500Hz, 2G 10min./1cycle, Period for 60min each

axis

Withstand Voltage I/P-O/P:3KVAC I/P-FG: 1.5KVAC

O/P-FG:0.5KVAC

Isolation Resistance I/P-O/P, I/P-FG, O/P-FG:500VDC / 100Mohms

Working Temp. Humidity -10C-+50C (Refer to O/P de-rating Curve), 20%-90%

Storage Temp. Humidity -20C+85C, 10%95% RH

Dimensions 215*115*50mm Case 912

Module weight 1.2Kgs

Safety Standards UL1950, TUV EN90950 Approved

EMC Standards CISPR22 (EN55022), IEC1000-4-2,3,4,5,6,8,11

IEC1000-3-2 Verification

Notes:

1. All parameters are specified at 230V I/P, rated load, 25C, 70% RH ambient

2. Ripple and noise are measured at 20MHz using a 12” twisted pair terminated with a 0.1uF and 47uF

capacitor.

3. Line regulation is measured from low line to high line at rated load.

4. Load regulation is measured for 0% to 100% rated load.

Table des matières

Manuels Alimentation populaires d'autres marques

Monacor

Monacor PS-12CCD Manuel utilisateur

VOLTIMA

VOLTIMA MagicBox 15 Manuel utilisateur

Agilent Technologies

Agilent Technologies 6032A Manuel utilisateur

Miller

Miller Auto Deltaweld 452 Manuel utilisateur

BCP

BCP PUOUBK Feuille d'instructions

HC 2210 Manuel utilisateur

Puls

Puls CT5.241 Manuel utilisateur

OCZ

OCZ ZX1250W Manuel utilisateur

iseg

iseg ECH 238 Manuel utilisateur

Power

Power XXL A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 6631B Manuel utilisateur

Renogy

Renogy PHOENIX 300 Manuel utilisateur

HP 6200B Manuel de service

Epson

Epson Stylus Scan 2500 Manuel d'utilisation

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuel utilisateur

Puls

Puls MiniLine ML50.100 Manuel utilisateur

Puls

Puls AS-Interface SLA4.100 Manuel utilisateur

Kenwood

Kenwood PS-60 Manuel utilisateur