TSec SpA MACS Manuel utilisateur

Carefully read this manual in its entirety.

You will find useful information to take full advantage of the product's potential, use it safely and obtain the best results.

MACS

Anti-intrusion perimeter system for rigid and

semi-rigid metal fences

Instruction manual

v1.1 - EN

Any distribution, alteration, translation or reproduction, partial or total, of this

document is strictly prohibited unless with prior authorization in writing from TSec

SpA, with the exception of the following actions:

lPrinting the document in its original format, totally or partially.

lTransferring the document on websites or other electronic systems.

lCopying contents without any modification and stating TSec SpA as

TSec SpA reserves the right to make modifications or improvements to the relative

documentation without prior notice.

Requests for authorization, additional copies of this manual or technical

information on the latter, must be addressed to:

TSec SpA

Via Gavardina Traversa I, 74

25081 Bedizzole (BS)

Italy

info@tsec.it

www.tsec.it

+39 030 57 85 302

Contents

Reception 5

Package contents 5

Get to know MACS 6

Introduction to MACS system 7

System start- up 8

The sensors (MACS- S3H) 8

The Master (MACS- MAS) 9

The Ethernet board (MACS- ETH) 11

Connection to the Ethernet board 12

Web interface 12

System installation 14

Things to know 15

Before installing the system 17

Install the sensors 18

Install the Master 21

Install the Ethernet board 23

System configuration 24

General concepts about sensors 25

Initial operations 26

Operate with the web interface 27

Diagnostics and maintenance 30

Diagnostics and troubleshooting 31

Firmware and web interface updates 32

Maintenance and cleaning 32

Appendix 33

Technical data 34

Disposal 36

Service and warranty 36

Updates to the instruction manual

Publication date Code Updates

11- 2018 MACS_instructions_en_v1.1 First publication

Provided documentation

Manual Code Date Format Distribution

Instruction manual (this manual) MACS_instructions_en_

v1.1

11-

2018

PDF Website www.tsec.it

MACS Installation instructions MACS_installation_en_

v1.0

01-

2019

Printed Supplied in MACS

packaging

MACS- KIT- CON Joining kit Installation

instructions

MACS- KIT- CON_

installation_en_v1.0

01-

2019 Printed Supplied in Joining kit

packaging

MACS- KIT- TERM Termination kit

Installation instructions

MACS- KIT- TERM_

installation_en_v1.0

01-

2019 Printed Supplied in Termination

kit packaging

Intended users of this instruction manual

Recipient Assignments Skills

Safety system designer lDefines the composition of

the system

Safety system expert

Installer lInstalls all system

components

lConfigures the system

Safety system expert

Maintenance technician lPerforms maintenance on

the system

High technical knowledge in the field of safety

systems

System owner / safety

manager

lMonitors the system -

Reception

Package contents

Sensor package

lPre- wired sensor chains

lFor each sensor:

llong and short screw

lcounter- plate

lT- cap

lspacer

lInstallation instructions

Master package

lCircuit board in watertight case

lFour screws per cover

Ethernet board package

MACS-ETH:

lCircuit board with support for DIN rail

lDIN rail

lMagnet

MACS-ETH-PS:

lCircuit board in metallic box with wired power supply unit (input: 230 V ac)

lMagnet

lBuffer battery (optional)

lInstallation instructions

Material excluded

lBus cable for connection of the Ethernet board and Master and for prolonging the intervals between

sensors.

lTermination kit.

lPossible cable joining kit.

lPossible self- drilling screws for installation of sensors on pole.

lEthernet cable to connect the Ethernet board.

Spare parts and accessories

For orders and consulting the spare parts and accessories catalog, contact the local distributor or

manufacturer.

Reception

Get to know MACS

Contents

This section includes the following topics:

Introduction to MACS system 7

System start-up 8

The sensors (MACS-S3H) 8

The Master (MACS-MAS) 9

The Ethernet board (MACS-ETH) 11

Connection to the Ethernet board 12

Web interface 12

Get to know MACS

Introduction to MACS system

Description

MACS is an anti- intrusion perimeter system for rigid and semi- rigid fences with metallic panels higher than

1.50 m (4.92 ft) and total height (panel and wall) over 1.70 m (5.57 ft).

Thanks to an accelerometer inside of each sensor and a proprietary algorithm, the system detects and signals

vibrations caused by climbing over the fence and other potentially damaging actions (e.g. attempted removal

of the fence). Furthermore, it distinguishes and filters innocuous vibrations caused by involuntary actions, like

accidental impacts or weather.

Control of the system is divided between two components, the Ethernet board and the Master. The Ethernet

board is the only component of the system to which supply power, the Master and the sensors receive power

supply from the Ethernet board. The system is configured and monitored via the web interface, accessible by

browser.

Main components

Component Code Description

Sensors MACS-S3H Up to 2 chains with 120 sensors each (bus 1 and bus 2)

Master MACS-MAS Electronic circuit board for managing the sensors

mounted in the watertight case for outdoor installation

Ethernet board MACS-ETH Communication electronic circuit board with the alarm

control panel and Ethernet port for access to the web

interface

Get to know MACS

Component Code Description

Bus cable MACS-CAB Proprietary bus cable

Web interface - Interface accessible by browser to configure and manage

the system

Applications

The system is suitable for large fences (e.g. military sites, airports, industrial sites, etc.) as well as residential

and commercial sites.

System start-up

The sequence of macro- procedures for starting up the system is presented as follows:

1. "Install the sensors" on page18.

2. "Install the Master" on page21.

3. "Install the Ethernet board" on page23.

4. "Initial operations" on page26.

5. "Manage system settings" on page28.

The sensors (MACS-S3H)

Functioning

The sensors detect the vibrations caused by motions of the fence thanks to an accelerometer and send the

signals to the Master via bus. The algorithm recognizes attempts to climb over the fence by filtering out

vibrations caused by accidental impacts or weather.

Sensor front

Part Description

ASensor body

BHole for fastening screw to pole or counter- plate

CBus cables

DT- cap

Get to know MACS

Sensor back

Part Description

ACounter- plate for panel installation

BSpacer for panel installation with thick mesh

CRubber fastening gasket

The Master (MACS-MAS)

Functions

The Master performs the following functions:

lManages the sensor chains.

lTransmits signals from the sensors to the Ethernet board.

Main components

Part Description

AWatertight box

BTerminal block for connecting sensor chains (see "Description of terminal block for connecting

sensor chains" on page22)

Get to know MACS

Part Description

CTerminal block for connecting Ethernet board (see "Description of terminal block for connecting

the Ethernet board " on page22)

DCable glands, for bus cables of the two sensor chains and towards the Ethernet board

LED

LED Color Description

LD2 Green Power supply status:

lSteady: powered up.

lOff:not powered up (see "LED of the Master" on page31).

LD9 Green Power supply status bus 2:

lSteady: powered up. In the start- up and configuration phase, the LED turns off for a few

seconds and then turns back on.

lOff:not powered up (see "LED of the Master" on page31).

LD10 Red Short- circuit bus 2:

lSteady: short- circuit

lOne flashing: short- circuit detected. The Master attempts to power up the bus again and

the LED turns off. If the short- circuit is detected again, the LED turns back on and stays on.

LD11 Green Power supply status bus 1:

lSteady: powered up. In the start- up and configuration phase, the LED turns off for a few

seconds and then turns back on.

lOff:not powered up (see "LED of the Master" on page31).

LD12 Red Short- circuit bus 1:

lSteady: short- circuit

lOne flashing: short- circuit detected. The Master attempts to power up the bus again and

the LED turns off. If the short- circuit is detected again, the LED turns back on and stays on.

LD15 Green Firmware status:

lFlashing: normal functioning.

lSteady or off: malfunctioning (see "LED of the Master" on page31).

Orange Sensor configuration status:

lSteady: configuration in progress. The sensor alarms are not read. The LED turns off after

about 30 s of inactivity in the web interface.

lOff: configuration concluded.

Get to know MACS

Table des matières

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur