TSC TTP-2410M Manuel utilisateur

TTP-2410M/346M/644M

TTP-246M Plus/344M Plus

Bar Code Printer Service Manual

4.2 Mechanism Fine Adjustment to Avoid Ribbon Wrinkles

This printer has been fully tested before delivery. There should be no ribbon wrinkle

presented on the media for general-purpose printing application. Ribbon wrinkle is related to

the media thickness, print head pressure balance, ribbon film characteristics, print darkness

setting…etc. In case the ribbon wrinkle happens, please follow the instructions below to

adjust the printer parts.

Adjustable

Printer

Parts

Symptom 1. Wrinkle happens from label lower left to

upper right direction ("Ԩ")

2. Wrinkle happens from label lower right

to upper left direction ("Ԫ")

Wrinkle

Example

Feed direction

Ribbon guide plate

Print head pressure

adjustment knob Z-axis mechanism

adjustment knob

TTP-2410M/346M/644M

TTP-246M Plus/344M Plus

Bar Code Printer Service Manual

Adjust the print head pressure adjustment knob

The print head pressure adjustment knob has 5

levels of settings. Clockwise direction adjustment

is to increase the print head pressure. Counter

Clockwise adjustment can decrease the print

head pressure.

If the wrinkle on the label starts from the lower left

side to upper right side, please do following

adjustment.

1. Decrease the right side print head pressure

adjustment knob setting 1 level per each

adjustment then print the label again to check if

wrinkle is gone.

2. If the right side print head adjustment knob

setting has been set to index 1 (the lowest

pressure index), please increase the left side

print head pressure.

3. If the left side print head adjustment knob

setting has been set to 5 (the highest pressure

index) the wrinkle can’t be avoid, please rotate

the both knobs back to setting 1 then rotate the

Z-axis mechanism adjustment knob clockwise

for a few degrees and print again for fine tune

the print head pressure distribution.

Note for step 3:

*Factory default setting, the Z-axis knob is rotated

counter clockwise to the end of thread.

*Turn the Z-axis mechanism adjustment knob

clockwise until you feel the knob touch the

mechanism for the first adjustment.

* If the wrinkle is still there, please turn the Z-axis

mechanism adjustment knob clockwise about

1/4 circle each time for adjustment

* If the winkled direction is change from "Ԩ" to "

Ԫ" by adjusting the Z-axis mechanism

adjustment knob, please turn the Z axis

mechanism adjustment knob counter clockwise

to avoid the wrinkle.

Adjust the print head pressure adjustment knob

The print head pressure adjustment knob has 5

levels of settings. Clockwise direction adjustment

is to increase the print head pressure. Counter

Clockwise adjustment can decrease the print

head pressure.

If the wrinkle on the label starts from the lower

right side to upper left side, please do following

adjustment.

1. Decrease the left side print head pressure

adjustment knob setting 1 level per each

adjustment then print the label again to check if

wrinkle is gone.

2. If the left side print head adjustment knob level

has been set to index 1 (the lowest index),

please increase the right side print head

pressure.

Right knob

Left knob Right knob

Left knob

Z axis mechanism

adjustment knob

Autres manuels pour TTP-2410M

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TSC Lecteur de codes-barres

TSC

TSC ME240 series Manuel utilisateur

TSC

TSC TTP-2410M Pro Manuel utilisateur

TSC

TSC Alpha-40L RFID Manuel utilisateur

TSC

TSC TTP-243 Series Manuel utilisateur

TSC

TSC Alpha-4L-W Manuel utilisateur

TSC

TSC MX240 Manuel utilisateur

TSC

TSC TTP-245HR Manuel utilisateur

TSC

TSC TTP-2610MT Series Manuel utilisateur

TSC

TSC MH261T Series Manuel utilisateur

TSC

TSC TTP-244 series Manuel utilisateur

TSC

TSC TDP-643R Plus series Manuel utilisateur

TSC

TSC Alpha-30L Series Manuel utilisateur

TSC

TSC TTP 243 Pro Manuel utilisateur

TSC

TSC MX340P Series Manuel utilisateur

TSC

TSC DA310 Series Manuel utilisateur

TSC

TSC TDM-20 Manuel utilisateur

TSC

TSC TDP-244 Series Manuel utilisateur

TSC

TSC MH261T Series Manuel utilisateur

TSC

TSC TX200 Series Manuel utilisateur

TSC

TSC TTP-244 Pro Series Manuel utilisateur

TSC

TSC TTP-244 series Manuel utilisateur

TSC

TSC TTP-2610MT Series Manuel utilisateur

TSC

TSC MH241 Series Manuel utilisateur

TSC

TSC TE200 series Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur