Trycom Technology TRP-C29U Manuel utilisateur
TRP-C29U
8-channel isolated digital input and 8-channel isolated digital
output(O.C) USB serial interface module, Support ASCII and
Modbus Protocol.
User’s Manual
Printed Dec. 2010 Rev 1.2
Trycom Technology Co.,Ltd
1F, No.2-11,Sihu street ,Yingge Township, Taipei, Taiwan ROC
Tel: 886-2-86781191 , Fax: 886-2-86781172
www.trycom.com.tw
Copyright
Copyright Notice: The information in this manual is subject to change without prior notice in order to improve reliability, design and function and
dosed not represent a commitment on the part of the manufacturer. No part of this manual may be reproduced, copied, or transmitted in any form
without the prior written permission of manufacturer. Acknowledgment Products mentioned in this manual are mentioned for identification purpose
only. Products manes appearing in this manual may or may not be registered trademarks or copyright of their respective companies.
1.Introduction
TRP-C29U is USB to serial interface that provides with 8 optical isolated digital input channels and
8-channel digital output open collector. All channel features screw terminals for convenient
connection of field signals as well as LED’s to indicate channel status. Input channels are equipped
with 3750Vms DC isolation . For easy user access, TRP-C29U can enter configuration mode and
self-test mode with outer dip-switch. TRP-C29U support both ASCII and Modbus protocol, with a
full set of command, dual watch-dog, and auto reset function. the module can be bi-directionally
remote controlled by PC in ASCII or Modbus RTU protocol.
1-1.Features
USB directly power supply input.
System get a seriall com port when USB plug in.
Support ASCII and Modbus RTU protocol.
Supports baud rates from 1.2Kbps to 115.2 Kbps.
All 8 channels digital input ca be used as counter.
Digital input signal with 3750Vrms isolation protection.
Dual watchdog: Module’s firmware, host computer traffic.
LED for each channels working status.
DIN rail and panel mount support.
Configured and self-test by outer dip-switch.
Support screw terminal.
1-2.Specifications
Built-in USB 2.0 to serial bridge.
Input channel: 8 digital input channels.
Input optical isolation: 3750 Vrms.
Input logical level 0 +/-1V (max).
Input logical level 1 +/- 4.0V ~ +/-30V.
Digital Input can be used as counter channel:8
Input counter: Dec 0~65535(max) or Hex 0000~FFFF (max).
Input impedance: 3Kohm.
Input Counter frequency: 100Hz.
Input distance: 500M (max).
Digital output Maximum voltage: +/-30V.
Digital output Maximum current: 100 mA.
Digital output isolation: 3750Vrms.
Communication interface: USB to serial .
Communication speed: Baud rate from 1.2kbps to 115.2Kbps.
Dual watchdog: Hardware reset circuit, module and host operating status.
Signal LED: Power on, all channels.
Power supply: Directly input from USB.
Connection type: Screw terminal, accepts AWG #12~32 wires
Power consumption: 1.2W.
℃Operating environment: -10 to 50 .
℃Storage temperature: -20 to 70 .
Humidity: 10-90% Non-condensing.
Dimension: 151mm X 75mm X 26mm .
Weight: 400g.
1-3. Panel Layout
1-4.Block Diagram
1-5. Pin Definitions
DI5 Digital Input CH 5 DI6 Digital Input CH 6
DI4 Digital Input CH 4 DI7 Digital Input CH 7
DI3 Digital Input CH 3 DO7 Open Collector output CH7
DI2 Digital Input CH 2 DO6 Open Collector output CH6
DI1 Digital Input CH 1 DO5 Open Collector output CH5
DI0 Digital Input CH 0 DO4 Open Collector output CH4
IN_COM External Voltage for Digital Input DO3 Open Collector output CH3
NC None DO2 Open Collector output CH2
NC RS485+ DO1 Open Collector output CH1
NC RS485- DO0 Open Collector output CH0
NC Input Voltage 10~30V EXT-GND External Voltage Ground for DO
NC Input Voltage Ground EXT-PWR External Voltage Power for DO
2-1. Communication Wiring
2-2. Wire Connection
3. USB to serial Driver Install
*Notice: When you finished the TRP-C29U USB to serial driver install, the O.S will detect
dual serial ports. For TRP-C29U there only one set of serial port can be use and the other
one set of serial port is non-function
1. Power on your computer and boot to Windows.
2. Put the driver CD in the CD-ROM then select the driver of O.S you want (See figure1)
Fig.1
3-1 .Install Vista32/64 driver
Find “MSSetup.exe” utility which in the Vista64 folder. Double click on MSSetup.exe to start
the installation process. Make sure that the User installing the driver must be a member of the
Administrator group on the system
You will get a “User Account Control” window saying “An unidentified program wants access to
your computer”. Click on Allow to continue installing the Driver.
You will get an installation window as below, press “Install” button to install the drivers for
High-Speed USB Multi Serial Device.
During the installation process, a “Windows Security” warning message pops up informing that
"Windows cannot verify the publisher of this driver software". Ignore the warning message by
clicking on the option “install this driver software anyway”.
You will get the above message two times and you have to select “install this driver software
anyway”. The utility displays a message stating “Installation completed”. Use “Exit” button to
complete the driver installation.
3-1-1.TRP-C29U Device Installation & Detection:
Connect TRP-C29U to the USB Host controller of the PC using a USB cable. The first time you
plug-in the cable into the USB port, Windows will start installing the device driver software. You
can see the installation status at the pop-up message of system tray. After installation, the pop-up
message says “Your devices are ready to use”, Device driver software installed successfully.
TRP-C29U device detection can be confirmed by checking at the Device manager. Check for “
High-Speed USB MultiSerial Compound Device” under Universal Serial Bus controllers and you
will find “MosChip High-Speed USB Serial Port (ComX)” under the category Ports (COM & LPT).
Here ‘X’ in ‘ComX’ represents the serial port number. You can see the same in the figure below.
3-2 .Install XP driver
Find MSSetup.exe and MSUninst.exe which in the folders for Win XP/2K and Win98/ME operation
system.
Use “MSSetup.exe” utility to install the driver. Double click on the utility to start the installation
process. Press “Install” button to install the drivers for High-Speed USB Multi serial Device.
During the installation process, a warning message will popup informing the user that the software
being used has not passed the Windows Logo testing. You can ignore the warning message by
clicking on the option “Continue Anyway”.
The utility will display a message stating “Installation completed”. Use “Exit” button to complete
the driver installation.
Connect TRP-C29U to the USB Host controller of the PC by using a USB cable. The first time you
plug the adapter into the USB port, Windows will bring up the "Found New Hardware Wizard"
window to guide you through the initial configuration process. Select the option “No, not this time”
and click on “Next” button to continue.
The following wizard helps you install the software for “High-Speed USB Multi Serial Compound
device”. Select the option “Install the software automatically” and click on “Next” to proceed
further.
Table des matières
Manuels Équipement d'enregistrement populaires d'autres marques
Strymon
Strymon NIGHTSKY Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur
Tews Technologies
Tews Technologies TPMC465 Manuel utilisateur
Honeywell
Honeywell Excel 50 Manuel utilisateur
SeaLevel
SeaLevel COMM+8.LPCI Manuel utilisateur
Arturia
Arturia AUDIOFUSE STUDIO Manuel utilisateur
