Trycom Technology TRP-C51 Manuel utilisateur

TRP-C51

User’s Manual

Bluetooth To RS232/422/485 Converter

User Manual

Printed DEC. 2007 Rev 1.0

reliability, design and function and dosed not represent a commitment on the part of the manufacturer. No part of this

manual may be reproduced, copied, or transmitted in any form without the prior written permission of manufacturer.

Acknowledgment Products mentioned in this manual are mentioned for identification purpose only. Products manes

appearing in this manual may or may not be registered trademarks or copyright of their respective companies.

1.Introduction

Based on Bluetooth technology TRP-C51 allows you to wirelessly connect your RS232/422/485

devices to systems within the range over to 100M, TRP-C51 features wide range power input,

auto RS232/422/485 signal switching and internal surge protection on RS422/485 lines. It also

supports all common data format and baud rate which can be configured by the bundled TRP-BT

utility from Windows system. TRP-C51 can operate in :direct link mode” and “paired mode” When

in paired mode, the user just need to power two devices, and they will automatically connect

without software and hardware changes on your systems that will replace your serial wire with a

completed transparent wireless connection. It can be used for wide range of applications for

wireless operation and monitoring process.

1-1.Features

¾Bluetooth V1.2 Class 1 compliance. (2.5mW/4dBm)

¾Transmission range over to 100M.

¾Auto directionally RS485 signal communication.

¾Support all common baud rate from 1.2K to 256Kbps.

¾Comfortable TRP-BT configuration software (Windows version)

¾RS232/422 and RS485 signal auto switching.

¾Master/Slave connection mode selectable by software.

¾LED indicators for Power/Link/TX/RX.

¾Surge protection on RS422/RS485.

¾Power supply: Screw terminal, or external DC adapter.

¾Wide input range power supply.

¾DIN rail and panel mount support.

1.-2.Specifications

¾Power requirement: DC voltage input from +10V to +30V.

¾RS232 signal: TXD, RXD, GND, RTS, CTS.

¾RS422/485 connection: industrial plug-in screw terminal.

¾RS485 signal: differential 2 half-duplex wires. (D+, D-)

¾RS422 signal: differential 4 full-duplex wires.(TX+, TX-, RX+, RX-)

¾Baud rate: 1.2Kbps to 256Kbps.

¾Data bit 5,6,7,8.

¾Support Parity check: None, Even, Odd.

¾Stop bit: 1, 2.

¾RS232 flow control RTS/CTS: Enable, Disable.

¾Host PC com port to TRP-C51 connection: use null modem female-female cable.

¾Plug-in screw terminal wiring: Accepts AWG #12 ~30 wires.

¾Wireless transmission distance: 100M.

¾Antenna cable length:1530mm.

¾RS422/485 distance: up to 4000ft. (1200M)

¾LED indicator: Power, Link, TX, and RX.

¾Power input type: Screw terminal or DC plug.(5.5*2.1*12mm/500mA)

¾Power consumption: 1.2 watt.

¾Operating temperature: 0 to 50℃.

¾Storage temperature: -20 to 65℃.

¾Humidity: 10-90% Non-condensing.

¾Dimension: 151mm X 75mm X 26mm.

¾Weight: 400g.

2. Hardware Description

2-1. Panel layout

2-2.Block Diagram

2-3. LED Indictor

PWR LED:

When power is properly supplied to TRP-C51, the PWR LED will on.

LINK LED:

TRP-C51 can be configured as Master mode or Slave mode. When TRP-C51 is in Master mode,

the LINK LED definition is as below.

A: Turn on/off in 150ms cycle – when TRP-C51 is in slave searching status.

B: Turn on/off in 1000ms cycle – When TRP-C51 is in slave connecting status.

C: Turn on— Master and Slave connection is successful.

D: Blinking— If there is activity such as data transmitting or receiving.

When TRP-C51 is in Slave mode the LINK LED definition is as below.

Turn on/off in the cycle of “1000ms on/ 3000ms off” – no connection.

Turn on— When Slave and Master connection is successful.

Blinking— When there is activity such as data transmitting or receiving.

TX LED:RS232/422/485 data transmitting.

RX LED: RS232/422/485 data receiving.

2-4. DIP Switch

There are 2 dip switch on TRP-C51. One 2-pin dip switch is for system configuration, another is a

4-pin dip switch for extension and no function.

2-4-1. The 2-Pin DIP-Switch for configuration mode

SW1,2: OFF OFF: Normal mode

SW1,2:ON ON: Configuration mode

SW1,SW2: OFF OFF -- Normal mode.

TRP-C51 can only work in normal mode. In this mode all system setting are completed.

SW1,SW2 : ON ON -- System configuration mode.

This mode is for system configuration change. When adjust the switch to ON/ON position

TRP-C51 will stop all activities. User may run TRP-BT utility to change the baud rate, UART

format or the other settings. After the configuration change completed, revert the switch to

OFF/OFF position and reboot the system. All the system changes will be effective after the

system reboot.

2-4 Micro Touch button

TRP-C51 micro touch button provides user with “new link” function when user want to drop

existing connection and create a new connection with new device.

The Micro touch button can only work when TRP-C51 is defined as Master. When TRP-C51 is in

Slave mode the button is no function.

The Micro touch button is no function, if TRP-C51 already had default “BD address”

3.Install TRP-C51

3-1. Serial Connection

The TRP-C51 is equipped with one DB-9 male connector which is configured as a DTE (data

terminal equipment) device. All PC COM ports are DTE ports.

A null modem cable is required to make a connection between the PC COM port and the

TRP-C51 serial port.

3-2. Power Connection

The TRP-C51 is equipped with a 2-pin terminal block and power jack. Power can be supplied

from terminal block or external DC plug. It support wide input range from +10~+30V DC/500mA

power supply. When power is correctly supplied the PWR LED will turn on and the system is

ready.

If the power input from external, Please use the power plug specification. (5.5*2.1*12 mm).

Warning: User can only choose one of following 2 power sources.

1. External DC adapter. 2. Screw terminal DC input

Do not use both power input simultaneously.

3-3. RS232 wiring connection

3-4. RS485 wiring connection

The RS485 mode supports the Transmit and Receive channels using 2-wire half-duplex

operation. Refer to the pin assignment for connection as below.

*The RTS/CTS must be disable if the user using the RS422/485 function.

3-5. RS422 wiring connection

The RS422 mode supports 4 channels with full duplex operation for Receive and Transmit, The

data lines are in differential pairs. Refer to the pin assignment for connection as below.

*The RTS/CTS must be disable if the user using the RS422/485 function.

4. Getting start

4-1.TRP-C51 default Settings

Bluetooth Status

Name: TRP-C51

Password: 1234

Connection Mode: Slave

Device: Discoverable

UART Status

Baud Rate: 9600

Data Bit: 8

Parity Check: None

Stop Bit: 1

RTS/CTS Flow Control: Disable

4-2. Configure TRP-C51

Step1. Use a Null modem cable (crossover female to female cable) to make a connection

between the TRP-C51 DB-9 connector and PC DB-9 connector.

Step.2 Run the TRP-BT Utility by window

User may find the TRP-BT utility in TRP-C51 support CD.

TRP-BT.EXE the configuration screen appears.

Step.3. Adjust 2-PIN SW to the ON, ON position (System configuration Mode) then power on

TRP-C51.

Step.4. Select the PC RS232 COM Port for TRP-C51.

Step.5 Click the “Read Configuration” button to read the TRP-C51 firmware configuration.

Step.6 Select the baud rate from 1200 bps ~ 256 K bps.

Step.7 Select the data bit form 5~8.

Step 8 Select the Parity Check.

Step 9 Select the Stop Bit.

Step 10 Select the RTS/CTS Flow Control.

*It must be disable if the user using the RS422/485 function.

Autres manuels pour TRP-C51

Table des matières

Autres manuels Trycom Technology Convertisseur de média

Trycom Technology

Trycom Technology TRP-C08X Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C06H Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C08H Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C08D Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C08 Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C68 Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C39 Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C31S Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C08H Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C51 Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C32S Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C08E Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C39S Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C34H Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C08S Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C37 Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C41 Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C51 Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C36 Manuel utilisateur

Trycom Technology

Trycom Technology TRP-C34X Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur