Trust SECURITY PLUS-LINE Manuel utilisateur

SECURITY PLUS-LINE

ALSET-2000

ALSET2000 WIRELESS SECURITY SYSTEM

QUICK INSTALL GUIDE

MULTI LANGUAGE

Item 71116 Version 1.0

Visit www.trust.com

for the latest instructions

2 3

O

u v w x

Learn button 2 sec

LED indicator

4 5

6 7

DELSET

LED indicator

Backplate

DELSET

SET

2 sec

DEL SET

SET

2 sec

8 9

10 11

Arm

O

ON button

4 sec

OFF button

Short press

ON button

OTHER

Tamper switch

13a

13b

Arm

ON button 4 sec

O

1.5 sec

Tamper switch

O

1.5 sec

O

OFF button 4 sec

85 sec.

19 20

O

ALSET-2000 WIRELESS SECURITY SYSTEM

1. Package content

The following products are included:

uALKCT-2000 Remote control

vALSIR-2000 Siren

wALMST-2000 Magnetic contact sensor

xALMDT-2000 Infrared motion sensor

NOTE: This is a quick installation guide, visit www.trust.com/71116 for more in depth info of the

individual products like:

- Speciﬁcations

- Mounting

- Reset/unpair

- Tamper switch

- LED indications

2. Open the ALSIR and place batteries

Open the siren by unscrewing the two screws beneath the light cap. When the screws are removed

the cap of the siren can be slid open. When the cap of the siren is slid open place 4x Alkaline D type

1.5V battery in the siren (not included). Observe the correct polarity of the batteries.

3. Put the ALSIR in learn mode

Slide open the cap and press and hold the siren learn button for about 2 second to enter learn mode.

The LED of the siren will be blinking (in the light cap). The learn mode lasts 15 seconds.

4. Open the ALMST and place batteries

Push with a sharp object on top of the magnetic sensor and pull o the backplate. Insert two 1,5V AAA

Alkaline batteries in the slot (not included). Observe the correct polarity of the batteries (place plus and

minus on the correct side)

ALSET-2000 WIRELESS SECURITY SYSTEM

5. Pair the ALMST to the ALSIR

Put the ALSIR in learn mode (see step 3). After putting the ALSIR in learn mode send a pair-signal by

pressing the SET button with a sharp object next to the battery slot of the magnetic sensor. The LED

indicator of the ALMST will ﬂash 5x to conﬁrm that the pairing has been done successfully.

6. Open the ALMDT and place batteries

Open the battery slot on the back side of the motion sensor by pushing the pull-tab down and

removing the battery cover. Insert two AA 1,5V Alkaline batteries as shown above (not included).

Observe the correct polarity of the batteries place plus and minus on the correct side. Close the

battery slot.

7. Pair the ALMDT to the ALSIR

Put the ALSIR in learn mode (see step 3). After putting the ALSIR in learn mode send a pair-signal by

pressing the SET button with a sharp object on the back of the sensor. The LED indicator of the ALMDT

will ﬂash 5x to conﬁrm that the pairing has been done successfully.

8. Open the ALKCT and place battery

Open the battery slot at the back of the ALKCT by sliding it down. Place the included 3V CR2477 battery

and close the battery slot. For more information on replacing and purchasing new batteries visit trust.

com/71115

9. Pair the ALKCT to the ALSIR

1. Put the ALSIR in learn mode (see step 3). Put the ALKCT in pair-mode by ﬁrst pressing the ON and

OFF button simultaneously for 4 sec (untill the LED of the ALKCT starts blinking).

2. Give a short press on the ON button to pair with the Siren. The LED indicator of the ALKCT will be

ﬂashing 5x to conﬁrm that the pairing has been done successfully.

ALSET-2000 WIRELESS SECURITY SYSTEM

10. Mount ALMST

Place the magnetic sensor on the window or door and make sure that both points on the two parts

are in line with each other. Mark the top and bottom of both parts. After marking the positions remove

the sensor.

11. Fasten the ALMST

Screw or tape both backplates of the magnetic sensor on the window or door according to the made

markings. When securing the backplates make sure both parts are mounted with as little space

between as possible (max. 5mm). Place both parts of the magnetic sensor back on the mounted

backplates.

Note: More detailed mounting instructions of the magnetic sensor are available at trust.com/71113

12. Mount ALMDT

Mount the backplate of the motion sensor on a ﬂat surface and secure it with screws. (Screws are

included).

13a. Fasten the ALMDT

Place the ALMDT on the backplate untill you hear a click. Make sure that the backplate is ﬁtted in the

location of the tamper switch.

Note: More detailed mounting instructions of the motion sensor are available at trust.com/71114

13b. Secure the ALMDT

When the ALMDT is placed on the backplate pull it down untill you hear a click to secure it and lock the

tamper switch.

Note: After arming the Siren it is possible to move in front of the sensor for 1 min. It takes ~1.5 minute

before the sensor will be completely active.

14. Mount ALSIR

To fasten the siren slide the cap o (see step 2) remove the batteries and screw the casing with

screws on a ﬂat surface according to the screwholes. (Screws are included). Keep attention that the

tamper switch is pressed to the surface after mounting the siren.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Trust Système de sécurité

Trust

Trust SECURITY PLUS-LINE ALSIR-2000 Manuel utilisateur

Trust

Trust SECURITY PLUS-LINE ALSET-2000 Manuel d'utilisation

Trust

Trust SECURITY PLUS-LINE ALSET-2000 Manuel utilisateur

Trust

Trust SECURITY PLUS-LINE ALSIR-2000 Manuel utilisateur

Trust

Trust 200AF Manuel utilisateur

Trust

Trust 200SA Manuel utilisateur

Trust

Trust 200DS Manuel utilisateur

Trust

Trust 140BM LCD WIRELESS OBSERVATION SYSTEM Manuel utilisateur

Trust

Trust SECURITY PLUS-LINE ALSIR-2000 Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur