True T-12FG Manuel utilisateur

............ www.truemfg.com ............

TABLE OF CONTENTS

Safety Information

Safety Precautions 1

Proper Disposal 2

Connecting Electricity 3

Adapter Plugs 3

Installation / Operation Instructions

Ownership 4

Required Tools 4

Uncrating 4

Leveling Cabinet 5

Installation of Castors or Optional Legs 6

Installing Optional Castors on a T-12FG 7

Wire Gauge Chart 8

Sealing Cabinet to Floor & Electrical Inst. 9

Start-up 10

Shelving Install/Operation & Light Switches 11

Grasslin Defrost Timer (Freezer Units Only) 12

Field Troubleshooting (Freezer Units Only) 13-14

Light Cover Install for T-12FG 15

Maintenance, Care & Cleaning

Cleaning Condenser Coil 16-17

Temperature Control Adjustment 18

Stainless Steel Equipment Care & Cleaning 19-20

Light Bulb Replacement 20

Warranty (U.S.A. & CANADA ONLY!) 21

INSTALLATION MANUAL FOR T-SERIES FREEZER /

REFRIGERATOR (SWING AND SLIDE DOOR)

T-SERIES

FREEZER / REFRIGERATOR

SWING & SLIDE DOOR

TRUE FOOD SERVICE EQUIPMENT, INC.

2001 East Terra Lane • P.O. Box 970 • O’Fallon, Missouri 63366

(636)-240-2400 • FAX (636)272-2408 • INT’L FAX (636)272-7546 • (800)325-6152

Parts Department (800)424-TRUE • Parts Department FAX# (636)272-9471

CONGRATULATIONS!

You have just purchased the finest commercial

freezer / refrigerator available. You can expect many

years of trouble-free operation.

T-23

TSD-47G

TSD-69

T-35

11/12/07 -20K SB #897001

*Spanish, German, French and Arabic versions included.

............ www.truemfg.com ............

True Food Service Equipment, Inc.

............ www.truemfg.com ............

SAFETY INFORMATION

True Food Service Equipment, Inc.

This refrigerator must be properly installed and

located in accordance with the Installation

Instructions before it is used.

Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.

Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

Keep fingers out of the “pinch point” areas;

clearances between the doors and between the

doors and cabinet are necessarily small; be

careful closing doors when children are in the

area.

NOTE: We strongly recommend that any

servicing be preformed by a qualified

individual.

Unplug the refrigerator before cleaning and

making repairs.

Setting temperature controls to the 0 position

does not remove power to the light circuit,

perimeter heaters, or evaporator fans.

WARNING!

Use this appliance for its intended purpose as described

in this Owner Manual.

How to Maintain Your Freezer /

Refrigerator to Receive the Most

Efficient and Successful Operation

You have selected one of the finest commercial refrigeration units made. It is

manufactured under strict quality controls with only the best quality materials

available. Your TRUE cooler when properly maintained will give you many

years of trouble-free service.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

............ www.truemfg.com ............

True Food Service Equipment, Inc.

SAFETY INFORMATION

PROPER DISPOSAL OF THE FREEZER /

REFRIGERATOR

DANGER!

RISK OF CHILD ENTRAPMENT

USE OF EXTENSION CORDS

NEVER USE AN EXTENSION CORD! TRUE will not warranty any refrigerator that has been

connected to an extension cord.

Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are

still dangerous… even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator,

please follow the instructions below to help pre-

vent accidents.

Before You Throw Away Your Old Refrigerator

or Freezer:

Take off the doors.

Leave the shelves in place so that children may

not easily climb inside.

Refrigerant Disposal

Your old refrigerator may have a cooling system

that uses “Ozone Depleting ” chemicals. If you are

throwing away your old refrigerator, make sure the

refrigerant is removed for proper disposal by a

qualified service technician. If you intentionally

release any refrigerants you can be subject to

fines and imprisonment under provisions of the

environmental regulations.

............ www.truemfg.com ............

True Food Service Equipment, Inc.

The power cord of this appliance is equipped with

a 3-prong (grounding) plug which mates with a

standard 3-prong (grounding) wall outlet to mini-

mize the possibility of electric shock hazard from

this appliance.

Have the wall outlet and circuit checked by a quali-

fied electrician to make sure the outlet is properly

grounded.

If the outlet is a standard 2-prong outlet, it is your

personal responsibility and obligation to have it

replaced with the properly grounded 3-prong wall

outlet.

The refrigerator should always be plugged into it’s

own individual electrical circuit, which has a volt-

age rating that matches the rating plate.

This provides the best performance and also pre-

vents overloading building wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull

straight out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When removing the refrigerator away from the wall,

be careful not to roll over or damage the power

cord.

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

WARNING!

USE OF ADAPTER PLUGS

NEVER USE AN ADAPTER PLUG! Because of potential safety hazards under certain conditions, we

strongly recommend against the use of an adapter plug.

SAFETY INFORMATION

(North America Use Only!)

NEMA plugs

TRUE uses these types of plugs.

If you do not have the right outlet

have a certified electrician install

the correct power source.

............ www.truemfg.com ............

True Food Service Equipment, Inc.

INSTALLATION / OPERATION INSTRUCTIONS

To insure that your unit works properly from the

first day, it must be installed properly. We highly

recommend a trained refrigeration mechanic and

electrician install your True equipment. The cost

of a professional installation is money well spent.

Before you start to install your True unit, carefully

inspect it for freight damage. If damage is discov-

ered, immediately file a claim with the delivery

freight carrier.

True is not responsible for damage incurred dur-

ing shipment.

OWNERSHIP

Adjustable Wrench

Phillips Head Screwdriver

Level

REQUIRED TOOLS

Step 1

The following procedure is recommended for

uncrating the unit:

A. Remove the outer packaging, (cardboard and

bubbles or styrofoam corners and clear plastic).

Inspect for concealed damage.Again, immediate-

ly file a claim with the freight carrier if there is

damage.

B. Move your unit as close to the final location as

possible before removing the wooden skid.

C. Remove door bracket on swinging glass door

models (see image 1-2). Sliding glass door

models contain shipping blocks (three for each

door). Remove the two styrofoam blocks taped

to the top of the door tracks (see image 3). The

shipping blocks are orange in color and by

opening the door a little the blocks can be

removed (see images 4-6). Do not throw the

bracket or blocks away. For future cabinet

movement the bracket and blocks will need to

be installed so the glass door does not receive

any damage. (See image for bracket and ship-

ping block removal)

Note: Keys for coolers with door locks are located

in warranty packets.

UNCRATING

INSTALLATION / OPERATION INSTRUCTIONS

1 2 3

456

............ www.truemfg.com ............

True Food Service Equipment, Inc.

INSTALLATION / OPERATION INSTRUCTIONS

Step 3

A. Set unit in its final location. Be sure there is adequate

ventilation in your room. Under extreme heat condi-

tions, (100°F+, 38°C+), you may want to install an

exhaust fan.

Warning

Warranty is void if ventilation is insufficient.

B. Proper leveling of your True cooler is critical to

operating success (for non-mobile models). Effective

condensate removal and door operation will be effected

by leveling.

C. The cooler should be leveled front to back and side

to side with a level.

D. Ensure that the drain hose or hoses are positioned in

the pan.

E. Free plug and cord from inside the lower rear of the

cooler (do not plug in).

F. The unit should be placed close enough to the elec-

trical supply so that extension cords are never used.

Warning

Compressor warranties are void if the unit is more

than 7 ft. (2.1m) from plug-in connection.

LEVELING

Step 2

A. Place packing material behind cabinet as a

cushion. Carefully lay the unit on its back to

remove skid.

When lifting unit remember to

leave the cabinet upright for 24 hours before

plugging into power source.

B. Remove skid by unscrewing all base rail anchor

brackets. Place skid to the side.

C. Carefully lift cabinet upright.

LOCATING

Removing

skid from

bottom of

cabinet.

REMOTE UNITS (This section applies to

remotes only!)

• Remote cabinets must be ordered as remote.

We do not recommend converting from a

standard self contained to remote system.

• All remote cabinets must be hard wired.

• No castors available.

• All remote cabinets come standard using 404A

refrigerant.

• All remote units come standard with expansion

valve, liquid line solenoid, heated condensate

pan, and defrost timer when applicable.

• Contact True Technical Service for BTU

requirements.

• No wiring necessary between cabinet and

condensing unit.

• All remote condensing units purchased from

True are 208/230 volts single phase.

If you have any questions regarding this sec-

tion, please call True at 1-(800)-325-6152.

Some units have a

polyester strap that

secures the cabinet to

the shipping skid. Cut

this polyester strap

and remove the

wood skid.

Polyester Strap

............ www.truemfg.com ............

True Food Service Equipment, Inc.

INSTALLATION / OPERATION INSTRUCTIONS

Rail End

Lower Rail

Assembly

Snug Fit

Here

Leveling Shim

CastorLeg

Bearing

Race

Lower Rail Assembly

Snug Fit

Here

Rail End

Thread castor into the under-

side of cabinet frame rail.

Thread leg into cabinet

bottom frame rail.

The end of the leg is

adjustable to easy leveling.

Use the tool provided to

tighten the castor into place.

For leveling, insert the shim

between the castor and frame rail.

1234

INSTALLATION OF CASTORS OR OPTIONAL LEGS

Important Safeguard for installation of leg/castor (Images 1-5 demonstrate procedure)

Step 4

Securing Castors and Legs

To obtain maximum strength and stability of the

unit, it is important that you make sure each castor

is secure. Optional legs are hand-tightened securely

against the lower rail assembly see image 4-5. The

bearing race on the castor or the top edge of the

leg must make firm contact with the rail.

Unit leveling

Four leveling shims have been provided for level-

ing castored units positioned on uneven floors.

Shims must be positioned between rail end and

bearing race.

A. Turn the bearing race counter-clockwise until

the cabinet is level. Level front to back and side to

side. (diagonally)

B. Install the desired number of shims, making sure

the slot of the shim is in contact with the threaded

stem of the castor. (See image 2)

C. If more than one shim is used, turn the slot at a

90° angle so they are not in line.

D. Turn the bearing race clockwise to tighten and

secure the castor by tightening the anchoring bolt

with a 3/4 inch open-end wrench or the tool

provided. (See image 3)

CAUTION

To avoid damage to lower rail assembly,

slowly raise unit to upright position.

Note: Open holes located on the cross members of the

frame rail should be plugged before unit is in use.

............ www.truemfg.com ............

True Food Service Equipment, Inc.

Final Location

A. Place styrofoam corners behind cooler for cushion

and carefully tilt unit on it’s back.

B. Remove the louvered grill by removing four

phillips-head screws.

C. Remove the four bolts from the skid with an

adjustable wrench, and locate the four castors. Castors

are placed inside cooler, within the bubble wrap.

D. Install one castor in each of the four female threaded

areas as indicated.

NOTE: Two out of the four castors are designated

with an “F” for front. These are provided with

hand-brakes. Position these castors in FRONT of

the unit.

E. When all castors have been threaded fully, replace

grill and lift unit; positioning it into its final location.

F. Ensure that the two front castors are positioned

FORWARD as illustrated and locked down with the

hand-brakes.

WARNING:

Unit may tip forward if procedure “F” is not

strictly followed.

G. Units final location should be adequately ventilated.

Conditions where heat exceeds 100ºF require an exhaust

fan.

H. Ensure that the drain hose for hoses are positioned

in the pan.

I. Free plug and cord from inside the lower rear of the

cooler (Do Not Plug In.)

WARNING:

Warranty is VOID if ventilation is insufficient.

J. The unit should be placed close enough to the

electrical supply so that extension cords are NEVER

used.

WARNING:

Compressor warranties are void if the unit is more

than 6 1/2ft. (1.98m) from plug-in connection.

K. Proper leveling of your TRUE cooler is critical to

operating success. Effective condensate removal and

door operation will be effected by leveling. Adjust

castors or add shims

INSTALLING OPTIONAL CASTORS ON A T-12FG

INSTALLATION / OPERATION INSTRUCTIONS

POSITIONING OF THE

CASTOR IS CRITICAL.

ORIENT THE CASTOR IN

THE FORWARD POSITION

AS SHOWN

............ www.truemfg.com ............

True Food Service Equipment, Inc.

INSTALLATION / OPERATION INSTRUCTIONS

Wire Gauge for 2% Voltage Drop in Supply Circuits

115 Volt Distance In Feet To Center of Load

Amps 20 30 40 50 60 70 80 90 100 120 140 160

2 141414141414141414141414

3 141414141414141414141412

4 141414141414141414121212

5 141414141414141212121010

6 141414141414121212101010

7 1414141414121212101010 8

8 14141414121212101010 8 8

9 141414121212101010 8 8 8

10 14 14 14 12 12 10 10 10 10 8 8 8

12 14 14 12 12 10 10 10 8 8 8 8 6

14 14 14 12 10 10 10 8 8 8 6 6 6

16 14 12 12 10 10 8 8 8 8 6 6 6

18 14 12 10 10 8 8 8 8 8 8 8 5

20 14 12 10 10 8 8 8 6 6 6 5 5

25 12 10 10 8 8 6 6 6 6 5 4 4

30 12 10 8 8 6 6 6 6 5 4 4 3

35 10 10 8 6 6 6 5 5 4 4 3 2

40 1088665544322

45 1086665443321

50 1086654433211

Wire Gauge for 2% Voltage Drop in Supply Circuits

230 Volts Distance In Feet To Center of Load

Amps 20 30 40 50 60 70 80 90 100 120 140 160

5 141414141414141414141414

6 141414141414141414141412

7 141414141414141414141212

8 141414141414141414121212

9 141414141414141412121210

10 14 14 14 14 14 14 14 12 12 12 10 10

12 14 14 14 14 14 14 12 12 12 10 10 10

14 14 14 14 14 14 12 12 12 10 10 10 8

16 14 14 14 14 12 12 12 10 10 10 8 8

18 14 14 14 12 12 12 10 10 10 8 8 8

20 14 14 14 12 10 10 10 10 10 8 8 8

25 14 14 12 12 10 10 10 10 8 8 6 6

30 14 12 12 10 10 10 8 8 8 6 6 6

35 14 12 10 10 10 8 8 8 8 6 6 5

40 14 12 10 10 8 8 8 6 6 6 5 5

50 12 10 10 8 6 6 6 6 6 5 4 4

60 12 10 8 6 6 6 6 6 5 4 4 3

70 10 10 8 6 6 6 5 5 4 4 2 2

80 1088665544322

90 1086655443311

100 1086654433211

CONDUCTORS AND CIRCUITS

Autres manuels pour T-12FG

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels True Réfrigérateur

True

True TCGD-50 Manuel utilisateur

True

True T-49-4 Manuel utilisateur

True

True TUC-60-LP Manuel utilisateur

True

True GDM-19 Manuel utilisateur

True

True TBB-2 Manuel utilisateur

True

True TDB-24-48-1-G-1 Manuel utilisateur

True

True TCGR-31 Manuel utilisateur

True

True TCGG-72-S Manuel utilisateur

True

True TR2RRT-2S-2S Manuel utilisateur

True

True Food Prep TFP-32-12M-D-2 Manuel utilisateur

True

True T-49-4-PT Manuel utilisateur

True

True TA1RPT-1S-1S Manuel utilisateur

True

True TA1RRI-1S Manuel utilisateur

True

True TSD-33G Manuel utilisateur

True

True TR1R-2HS Manuel utilisateur

True

True T-23 Manuel utilisateur

True

True TCGD-31 Manuel utilisateur

True

True T-12G Manuel utilisateur

True

True TRCB-110 Manuel utilisateur

True

True T-23PT Manuel utilisateur

True

True TUC-48D-4 Manuel utilisateur

True

True TBB-3G-S Manuel utilisateur

True

True TUC-48-LP Manuel utilisateur

True

True T-23DT Manuel utilisateur

Manuels Réfrigérateur populaires d'autres marques

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Manuel utilisateur

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Manuel utilisateur

Sharp

Sharp SJ-BA31IEXW2-EU Manuel utilisateur

CORBERO

CORBERO CC2300MCW Manuel utilisateur

KitchenAid

KitchenAid 2205264 Manuel utilisateur

Stengel

Stengel KU 1101 A++ Manuel utilisateur

NEFF

NEFF KI181 Series Manuel utilisateur

Hoshizaki

Hoshizaki Reach-In Manuel utilisateur

Amana

Amana ASD2524VES00 Manuel utilisateur

BOMANN

BOMANN KGC 213 Manuel utilisateur

Danby

Danby DAR044A1SLDD Instructions de montage

Samsung

Samsung RF323TE Manuel utilisateur

Beko

Beko CSA31022 Manuel utilisateur

IKEA

IKEA FROSTIG C 185 E Manuel utilisateur

Electrolux

Electrolux ER 6821 D Manuel utilisateur

Frigidaire

Frigidaire FSC23R5DW9 Manuel utilisateur

Beko

Beko LSP4579W Manuel utilisateur

Teledyne

Teledyne 6712FR and Mode d'emploi