TRU Audio Wraith Series Manuel utilisateur
Description
TruAudio is proud to introduce a revolutionary new
design, the Wraith series of invisible in-wall speakers
and subwoofers. Extremely versatile in their ability to
support both multiroom audio and surround
applications, the Wraith Series literally disappears
into any space.
Box Contents
WR24 Speaker
• 2 in-wall speakers
• 2 wood spacers per speaker
• 2 sets of fiber tape
• 2 sets of speaker overload protection and
crossover (WRPRO), 1 per speaker
WR40 Subwoofer
• 1 in-wall subwoofer
• 1 wood spacer
• 1 set of fiber tape
Speaker Placement - WR24 Speaker
Place wood spacer on the wall where you would like
to install the speaker and draw a line around the
OUTSIDE of the template. Carefully cut along the line
and remove the piece of sheetrock. Make sure the
outside edges of the speaker holes line up with the
studs. Half of the studs should be visible for the
screws to attach. (If the wall is not pre-framed it is
recommended to add a piece of 1x4 wood along the
top & bottom of the cutout for the speaker to attach
to.)
Wiring WR24 Speaker
Run your speaker wires from your amplifier to the “IN”
on the WRPRO protection unit. Then run speaker
wires from the WRPRO “OUT” to the speaker. Attach
the black & red wires to the speaker as seen in the
image below.
Insulation
Fit mineral wool or fiberglass insulation (not included)
behind the speaker, be sure there is no compression
between the insulation and the back of the speaker.
MANDATORY:
The WRPRO MUST BE USED.
The WRPRO must be used in line between the
speaker and your amplifier. The speaker will blow
if you send a signal directly to the speaker and
will not be covered under warranty.
User Manual
The protection unit “WRPRO” serves as an
extended overload protection and crossover that
also reacts to fast impulses. These speakers are
ONLY warranteed if this unit is used. When using the
WRPRO you will get the best performance from your
speakers.
14.5”
Amplifer
WRPRO
WR24
1
Insulation
Fit mineral wool or fiberglass insulation (not included)
behind the speaker, be sure there is no compression
between the insulation and the back of the speaker.
Amplifier
When using the WR40 subwoofer you MUST use only
the TRU-S500DSP with the appropriate DSP (WR40)
to power it. Using any other amplifier will void your
warranty.
After wiring the the WR40 to the TRU-S500DSP and
setting it to DSP setting (WR40) please set the
volume knob to no higher than -2.
Speaker Placement - WR40 Subwoofer
Place wood spacer on the wall where you would like
to install the subwoofer and draw a line around the
OUTSIDE of the template. Carefully cut along the line
and remove the piece of sheetrock. Make sure the
outside edges of the speaker holes line up with the
studs. Half of the studs should be visible for the
screws to attach. (If the wall is not pre-framed it is
recommended to add a piece of 1x4 wood along the
top & bottom of the cutout for the speaker to attach
to.)
Mounting the Speaker
The speaker should fit in the opening you cut with no
more than a 3/16” gap around the speaker. There are 2
included wood templates (2 thicknesses), install one,
both or neither to get the speaker to lay close to the
wall surface. Screw the speaker into the studs.
Finishing
After testing the the speaker and assuring everything is
correct you will need to have a skilled drywall spackler
fill in the gaps around the speaker with drywall spackle
( DO NOT USE - lightweight joint compound) and lay
the included drywall tape over the joint compound over
the seams. Next spackle the entire speaker area
smooth to blend into the wall, no thicker than 2mm.
Once the joint compound is dry, sand smooth and
paint.
IMPORTANT!
You must now play music through the
speaker before continuing to the next step.
3/16” gap
TRU-S500DSP
ATTENTION
CAUTION
RISQUEDE CHOC ELECRIQUE
NEPAS OUVRIR
RISKOF ELECTRI C SHOCK
DONOT OPEN
14.5”
2
Mounting the Speaker
The sub should fit in the opening you cut with no more
than a 3/16” gap around the sub. There are 2 included
wood templates (2 thicknesses), install one, both or
neither to get the sub to lay close to the wall surface.
Now screw the sub into the studs.
3/16” Gap
Finishing
After testing the the sub and assuring everything is
correct you will need to lay the included mesh over the
subwoofer and trim out about 1” around the port at the
bottom of the subwoofer.
Next have a skilled drywall spackler fill in the gaps
around the sub with drywall spackle ( DO NOT USE -
lightweight joint compound) and lay the included
drywall mesh over the joint compound over the
seams. Next spackle the entire speaker area smooth
to blend into the wall, no thicker than 2mm.
Once the joint compound is dry, sand smooth and
paint.
1”
IMPORTANT!
You must now play music through the
speaker before continuing to the next step.
WR24 WR24
Wiring WR24 Speaker - Dual Voice Coil
Speaker
In order to wire the WR24 as a dual voice coil speaker
you MUST purchase an additional WRPRO (two
total).
Remove the black and red jumper wire.
Alternative Way to Wire W24 Speaker
Remove
3
Specifications
WRPRO
Speaker level protection unit and crossover used to enhance the sound and protect the WR24 speakers
from mechanical overload.
Dimensions: 1.9” (48mm) x 3.1” (79mm) x 5.9” (150mm)
WR24 WR40
SoundVision Technologies dba TRUAUDIO
PRODUCT WARRANTY
LIMITED FIVE (5) YEAR WARRANTY TruAudio warrants to the original purchaser, when purchased from an authorized TruAudio Dealer/Distributor
and installed by a TruAudio installer, this product will be free from defective workmanship and materials in the initial installation for the period stated
above. Subject to the additional limitations stated below, does not include damage to associated equipment which may result for any reason from use
with this product, and does not include product failure caused by negligence, improper installation, misuse (e.g. overdriving the amplifier or speaker,
excessive heat or cold or humidity, outdoor installation). TruAudio will, during the warranty period, either repair the defect or replace the product with
a new or remanufactured product or a reasonable equivalent, and arrange at its acceptable expense, to reinstall this product and prepare the surface
of the speaker and mount for finishing, and nothing more. Does not include re-finishing of the wall or speaker.
It is the policy of TRUAUDIO to continuously incorporate improvements into our products. All specifications are
subject to change without notice. If you have any questions regarding this or any other TRUAUDIO products,
please visit www.TruAudio.com
Office: 1-888-858-1555, Monday-Friday 7 am - 6 pm MST.
Email: [email protected]
TruAudio
198 N Old Highway 91
Hurricane, UT 84737 USA
Power:
Impedance:
Freq. Range:
Dispersion:
Max SPL:
Dimensions:
Weight:
50W*
4Ω (2 @ 8Ω)
70 Hz - 18kHz
180º x 180º
105 db 1 w/1 m
24.38” (619mm) x
15.75”(400mm) x
2.2” (56mm)
2.1 lbs
Power:
Impedance:
Freq. Range:
Dispersion:
Max SPL:
Dimensions:
Weight:
150W Max
4Ω
35 - 150 Hz
180º x 180º
108 db 1 w/1 m
39.38” (1000mm) x
15.75”(400mm) x
4.0” (101mm)
25.5 lbs
*Power rating as per application of a high-pass filter. No electronic low-frequency boost must be used. Resulting damages from mechanical
overload are excluded from the warranty.
WR24
WRPRO
WRPRO
Attach the black and red wires from the WRPRO to
driver 1 and then attach the black and red wires from
the other WRPRO to the second driver 2.
To Amplifer
To Amplifer
4
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels TRU Audio Intervenants
TRU Audio
TRU Audio PAKCROWN Manuel utilisateur
TRU Audio
TRU Audio SB-CUSTOM-LC Manuel utilisateur
TRU Audio
TRU Audio BeatDrop 8 Series Manuel utilisateur
TRU Audio
TRU Audio ULTRASCAPE PRO Manuel utilisateur
TRU Audio
TRU Audio GPW-6 Manuel utilisateur
TRU Audio
TRU Audio AS-1 Manuel utilisateur
TRU Audio
TRU Audio GP-4 Manuel utilisateur
TRU Audio
TRU Audio Acoustiscape AS-1 Manuel utilisateur
TRU Audio
TRU Audio B23 series Manuel utilisateur
TRU Audio
TRU Audio GHT-66P Manuel utilisateur
TRU Audio
TRU Audio CP-6 Manuel utilisateur
TRU Audio
TRU Audio HARDSCAPE Manuel utilisateur
TRU Audio
TRU Audio Ghost GP-4 Manuel utilisateur
TRU Audio
TRU Audio CP-5 Manuel utilisateur
TRU Audio
TRU Audio Ghost HT Series Manuel utilisateur
TRU Audio
TRU Audio OP-5.2 Manuel utilisateur
TRU Audio
TRU Audio Ghost Series Manuel utilisateur
TRU Audio
TRU Audio Thin-Ceiling-P Manuel utilisateur
TRU Audio
TRU Audio SAT3 Manuel utilisateur
TRU Audio
TRU Audio LW Series Manuel utilisateur
Manuels Intervenants populaires d'autres marques
Bowers & Wilkins
Bowers & Wilkins 4 Manuel utilisateur
Sonance
Sonance SONOS OUTDOOR Series Manuel utilisateur
Electro-Voice
Electro-Voice EVID FM4.2 Manuel utilisateur
Pioneer
Pioneer XW-HTD630 Manuel utilisateur
Onn
Onn BWA16AA002 Manuel utilisateur
HP
HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur