Troy-Bilt 1904 Manuel utilisateur

IMPORTANT: Read entire owner’s manual before you

attempt to assemble or operate your new pressure washer.

REMOVE PRESSURE

WASHER FROM

CARTON

• Remove the parts bag packed with pressure washer.

• Slice two corners at the end of carton from top to

bottom so the panel can be folded down flat, then

remove all packing material.

• Roll pressure washer out of carton.

Carton Contents

Items in the carton include:

• Main Unit

• Safety Goggles

• Handle

• Plastic Accessory Tray

• High Pressure Hose

• Spray Gun

• Nozzle Extension with Quick Connect Fitting

• Oil Bottle

• Parts Bag (which includes the following):

• Owner’s Manual

• Engine Manual

• Owner’s Registration Card

• Bag containing 5 multi–colored Quick Connect Spray

Tips

• Maintenance Kit

• Handle Fastening Hardware Kit (which includes):

• Carriage Bolt

• “L” Bolt

• Plastic Knobs (2)

• “J” Hook

• Chemical Hose Clip

• Self Tapping Screws (5)

PREPARING PRESSURE

WASHER FOR USE

If you have any problems with the assembly of your

pressure washer or if parts are missing or damaged, call the

pressure washer helpline at 1-888-611-6708.

To prepare your pressure washer for operation, you

will need to perform these tasks:

1. Fill out and send in registration card.

2. Attach accessory tray to handle, then attach handle to

main unit.

3. Add oil to engine crankcase.

4. Add fuel to fuel tank.

5. Connect high pressure hose to spray gun and pump.

6. Connect water supply to pump.

7. Attach nozzle extension to spray gun.

8. Select/attach quick connect spray tip to nozzle

extension.

Attach Handle and Accessory Tray

NOTE: All assembly operations given in this section will be

described from the perspective of assembling the pressure

washer from the rear.

1. Slide the plastic accessory tray onto the handle and

align the holes in the accessory tray with the holes on

the handle (Figure 1).

Figure 1 — Attach Accessory Tray

Section

Assembly

10. Start the engine according to instructions given in the

engine owner’s manual.

NOTE: If the recoil starter is hard to pull, it may be

necessary to squeeze the gun trigger to relieve internal

pump pressure.

How to StopYour Pressure Washer

• Move variable pressure control lever to “Stop” position.

• Turn engine off according to instructions given in the

engine owner’s manual.

•Squeeze trigger on the spray gun to relieve

pressure in the hose.

NOTE: A small amount of water will squirt out when you

release the pressure.

How to Use Accessory Tray

The unit is equipped with an accessory tray with places to

store your nozzle extension and quick connect spray tips,

and slots to hold the cleaning solution bottle and the

detergent siphoning filter.There are also two hooks at the

ends of the handle to hold your spray gun and high

pressure hose.

NOTE: The extra holes in the tray are for storing a brush

and a turbo wand.The brush and turbo wand are NOT

included with your pressure washer.You can buy these

items as optional accessories.

1. Place the nozzle extension through the hole on the

accessory tray, as shown in Figure 13.

2. Hang your chemical solution bottle on the “J” hook

and place the detergent siphoning filter in the last slot

on the left (Figure 13).

3. Place the spray gun on the hook attached to the

accessory tray on the right side of the unit (Figure 13).

4. Hang the high pressure hose on the hook attached to

the accessory tray on the left side of the unit as shown

on page 4.

Figure 13 — Typical Accessory Tray

Section 4: Operation

How to Use the Spray Tips

CAUTION! NEVER exchange spray tips without

locking the safety latch on the trigger.

The quick–connect on the nozzle extension allows you to

switch between five different spray tips.The spray tips vary

the spray pattern as shown below (Figure 14).

Follow these instructions to change spray tips:

1. Engage the safety latch on the spray gun.

2. Pull back the collar on the quick–connect and pull the

current spray tip off. Store the spray tips in the space

provided on the handles storage panel.

NOTE: For a more gentle rinse, select the white 40° or

green 25° spray tip.To scour the surface, select the yellow

15° or red 0° spray tip.To apply chemical, select the black

spray tip.

3. Pull back on the collar, insert the new spray tip and

release the collar.Tug on the spray tip to make sure it

is securely in place.

4. For most effective cleaning, keep the spray tip from 8

to 24 inches away from the cleaning surface. If you get

the spray tip too close, you may damage the cleaning

surface.

5. DO NOT get closer than 6 inches when cleaning tires.

Cleaning and Applying Chemical

CAUTION! You must attach all hoses before you

start the engine. Starting the engine without all the hoses

connected and without the water turned ON will damage

the pump.

IMPORTANT: Use soaps designed specifically for

pressure washers. Household detergents could damage

the pump.

To apply detergent follow these steps:

1. Review the use of the spray tips.

2. Prepare the detergent solution as required by the

manufacturer.

3. Hang the detergent solution on the “J” hook attached

to the accessory tray, as shown in Figure 15.

Figure 15 — Insert Filter into Container

White

40°

Green

25°

Black Yellow

15°

Red

0°

Low Pressure

Use to

apply

chemical

High Pressure

Figure 14 — Spray Tips

Section 4: Operation

Autres manuels pour 1904

Table des matières

Autres manuels Troy-Bilt Nettoyeur haute pression

Troy-Bilt

Troy-Bilt 1905 Manuel utilisateur

Troy-Bilt

Troy-Bilt 1902 Manuel utilisateur

Troy-Bilt

Troy-Bilt 20213 Manuel utilisateur

Troy-Bilt

Troy-Bilt 1904 Manuel utilisateur

Troy-Bilt

Troy-Bilt 020242-4 Manuel utilisateur

Troy-Bilt

Troy-Bilt 20241 Manuel utilisateur

Troy-Bilt

Troy-Bilt 2500 MAX PSI Manuel utilisateur

Troy-Bilt

Troy-Bilt 20207 Manuel utilisateur

Troy-Bilt

Troy-Bilt 20209 Manuel utilisateur

Troy-Bilt

Troy-Bilt 20295 Manuel utilisateur

Troy-Bilt

Troy-Bilt 20242 Manuel utilisateur

Troy-Bilt

Troy-Bilt 1904 Manuel utilisateur

Troy-Bilt

Troy-Bilt 20210 Manuel utilisateur

Troy-Bilt

Troy-Bilt 20245 Manuel utilisateur

Troy-Bilt

Troy-Bilt 1904 Manuel utilisateur

Troy-Bilt

Troy-Bilt 1903 Manuel utilisateur

Troy-Bilt

Troy-Bilt 3000 PSI Manuel utilisateur

Troy-Bilt

Troy-Bilt 20296 Manuel utilisateur

Troy-Bilt

Troy-Bilt 020344-2 Manuel utilisateur

Troy-Bilt

Troy-Bilt 1902 Manuel utilisateur

Troy-Bilt

Troy-Bilt 0020242-1 Manuel utilisateur

Troy-Bilt

Troy-Bilt 20287 Manuel utilisateur

Troy-Bilt

Troy-Bilt 020213 Manuel utilisateur

Troy-Bilt

Troy-Bilt 1904 Manuel utilisateur

Manuels Nettoyeur haute pression populaires d'autres marques

Shark

Shark RG-232637 Manuel utilisateur

Shakti Technology

Shakti Technology S3 Manuel utilisateur

Kärcher

Kärcher K 4 Pure Manuel utilisateur

Porter-Cable

Porter-Cable D25806-025-2 Manuel utilisateur

REM POWER

REM POWER HDEm 662 Manuel utilisateur

Landa

Landa HS-3000 Manuel utilisateur

Craftsman

Craftsman 580.752270 Manuel utilisateur

HIKOKI

HIKOKI AW 100 Manuel utilisateur

Delco

Delco DC 1302 Manuel utilisateur

Kärcher

Kärcher K 3 Full Control Manuel utilisateur

BIEMMEDUE

BIEMMEDUE 120/10 - 170/13 Manuel utilisateur

ARKSEN

ARKSEN 014-HG-14141-HR Manuel utilisateur

Black & Decker

Black & Decker PW1700SPX Manuel utilisateur

Kärcher

Kärcher 595 - SPARE Mode d’emploi

Kranzle

Kranzle B 10 200 Manuel utilisateur

Stihl

Stihl RE 90 Manuel utilisateur

Husky

Husky HU80911 Manuel utilisateur

PowR-Quip

PowR-Quip PQ-2600 Manuel utilisateur