Trovan ARE H5 Manuel utilisateur

Operating Instructions

Hand Held ISO Reader ARE H5

--------------------------------------------------------------------------------2/33--------------------------------------------------------------------------------

Table of content

1INTRODUCTION ............................................................................................................5

2OVERVIEW....................................................................................................................5

2.1 Control elements .......................................................................................................................................6

3SHORT FORM OPERATING INSTRUCTION ..................................................................7

3.1 Installation of the battery..........................................................................................................................7

3.2 Power on / off ...........................................................................................................................................7

3.3 Reading a transponder ..............................................................................................................................7

3.4 Database...................................................................................................................................................9

4DETAILED DESCRIPTION OF THE OPERATING MODES .......................................... 10

4.1 Stand-By mode........................................................................................................................................10

4.2 Standard mode........................................................................................................................................10

4.3 Start reading...........................................................................................................................................10

4.4 Data storage ...........................................................................................................................................10

4.5 Built in memory ......................................................................................................................................11

4.6 Display of Accumulator Capacity .............................................................................................................11

5FUNCTION OF THE MENUS ....................................................................................... 12

5.1 Menu: "Set Attribute" .............................................................................................................................13

5.2 The menu "Operating Mode"....................................................................................................................14

5.2.1 Operating Mode "Online"...................................................................................................................14

5.2.2 Transmission format used for the serial interface. .............................................................................15

5.2.3 Terminating the "Data>Serial" mode.................................................................................................15

5.2.4 Online H, Read/Transf. .....................................................................................................................15

5.2.5 The database mode...........................................................................................................................16

5.3 Interface .................................................................................................................................................17

5.4 Change Bluetooth Role............................................................................................................................18

5.5 Change Bluetooth Partner.......................................................................................................................18

--------------------------------------------------------------------------------3/33--------------------------------------------------------------------------------

5.6 The menu "Lock Up Reader" ...................................................................................................................19

5.7 The menu "Clear memory".......................................................................................................................19

5.8 The menu "Code format" to adjust for the ISO-data format. .....................................................................20

5.8.1 Formats available for representation of the code ...............................................................................20

5.9 The menu "Set Date" ...............................................................................................................................21

5.10 The menu "Set time"............................................................................................................................21

5.11 The menu "Language"..........................................................................................................................22

5.12 The menu "timeout" .............................................................................................................................22

5.13 Software Verion ..................................................................................................................................22

6DEVICE ADJUSTMENTS BY AN EXTERNAL PC ....................................................... 23

7ANNEX ........................................................................................................................24

7.1 Specification ...........................................................................................................................................24

7.2 Type designations, supplied items and accessories ...................................................................................25

7.3 Operation with other RF ID Equipment ...................................................................................................25

7.4 Reading distance .....................................................................................................................................25

7.5 Safety Instruction....................................................................................................................................27

7.5.1 Reader .............................................................................................................................................27

7.5.2 Safety instructions for rechargeable li-ion batteries...........................................................................27

7.6 Driver installation for USB devices..........................................................................................................28

7.7 Glossary ..................................................................................................................................................31

7.8 Control Characters used in the "online mode"...........................................................................................31

7.9 Documentation, References.....................................................................................................................32

7.10 Notification of changes ........................................................................................................................32

7.11 Contacts ..............................................................................................................................................33

2001 by AEG Identifikationssysteme GmbH

--------------------------------------------------------------------------------4/33--------------------------------------------------------------------------------

Microsoft and Windows are registered trademarks of Microsoft Corp.

--------------------------------------------------------------------------------5/33--------------------------------------------------------------------------------

1Introduction

The ARE H5 is a hand held, high performance reader especially designed for animal identification. It

can read the data content of several transponder systems, store these data in its memory and transfer

them into a PC at a later stage.

This multi mode reader is capable to read the following transponder types, according to ISO

11784/11785:

FDX-B

HDX

Destron

Datamars

Trovan

PSK1

PSK2

ASK 64bit Manchester coding (e.g. transponder equipped with the EM chip 4102).

The ARE H5 does not synchronize with other HDX readers operating in close vicinity.

Before the initial use of this ARE H5 reader please study this manual carefully. It will explain the dif-

ferent features and modes, in order to make optimum use of all the capabilities of the system.

2Overview

The present manual is structured in the following way:

chapter 2.1 the control elements are described

chapter 3 contains a short form operating instruction for a quick test

chapter 4 describes in detail the features and operating modes of the ARE H5

chapter 5 the different menus are explained

chapter 6 give the interaction of the ARE H5 with an external data base

chapter 7 technical data, specifications and safety instructions

--------------------------------------------------------------------------------6/33--------------------------------------------------------------------------------

2.1 Control elements

Figure 2-1: location of the operating elements

--------------------------------------------------------------------------------7/33--------------------------------------------------------------------------------

3Short Form Operating Instruction

3.1 Installation of the battery

Slide the battery into its compartment until it clicks ((8) in Figure 2-1). Type of battery: Li-Ion

BP608 (AEG ID Order-NR. 70178).

Caution: Do use batteries Type Li-ion BP 608 only. The reader may be damaged by using batter-

ies which are not suitable. To charge the battery, remove it carefully from its compartment and

plug it into the appropriate charger.

Respect the dangers and follow the safety instructions about the proper use of rechargeable

lithium-ion batteries.

3.2 Power on / off

The reader is switched on by pressing the main button

((1) in Figure 2-1).

It is now in the Stand-by mode.

It will switch off again automatically, if no other buttons

has been pressed within timeout.

3.3 Reading a transponder

In the Stand-by mode: press the main button.

In the power off mode: press the main button twice.

Now the reader starts the reading mode. The

display shows:

in Database mode, or

in Online mode.

Off

Stand-by

7 5

8 4

9 3

10s Press main button

Read

transponder

7 5

8 4

9 3

5s Press main button

NoRead

code

read

--------------------------------------------------------------------------------8/33--------------------------------------------------------------------------------

Approach a transponder with the reader

. The reader emits a beep when the transponder has been

read successfully. The transponder code is shown on the display.

In Database mode the transponder a text can be assigned

. If the transponder actually read is al-

ready in the reader database, and if for its number a text is assigned, it is displayed in the second

line on the left side. With reading the transponder is assigned to an attribute that is selected in the

reader. The attribute2text is displayed in the second line on the right side. In this example the

“PPQ-7” (transponder text) is “in stock” (attribute text).

The same can be done with ISO Animal transponders if the code format is set to “ISO Attributes”.

In this example the cow “Elsa” (transponder text) is on the “meadow” (attribute text).

ISO standard is specified with the following display:

In this case the second display line contains the “Retagging Counter” and the “User Information

Field”. Additional ISO data saved on the transponder. This display is shown if code format “ISO

Animal” is selected.

If, no transponder has been read within 5 s, the reader terminates the reading mode and goes back

to stand-by. The display shows:

Typical reading distances are given in chapter 7.1

See the data transmission protocol document

--------------------------------------------------------------------------------9/33--------------------------------------------------------------------------------

With the left arrow button the last read transponder is shown.

With the right arrow button date and time is shown:

3.4 Database

When a reading had been accomplished successfully - i.e. it had been performed within the given time

frame - the database will be checked whether this transponder code is already stored.

If the new code is not found in the database, it will be stored as a new record. This record is com-

posed of the code, the transponder type, time and date, as well as an attribute. The attribute may

be selected from the 26 capital letters A to Z.

If the new code is already stored in the database, it will be stored again only, when the attribute

(see chapter 5.1) differs from that of the old record.

If the new code is already stored in the database with the very same attribute, no new record will

be stored. In this case the reader emits 2 successive beeps.

--------------------------------------------------------------------------------10/33--------------------------------------------------------------------------------

4Detailed description of the operating modes

4.1 Stand-By mode

Pressing the main button once puts the reader into the stand-by mode. Starting from this mode, it can

be transferred - either into the reading mode - or into the sub menus. These sub menus allow to change

the specific settings of the reader. Furthermore, the result of the last reading or the actual date and

time can be displayed in the stand-by mode. This is achieved by pressing the buttons "arrow left" and

"arrow right".

In order to save battery power, the reader shuts down automatically if no button has been pressed

within 10 s. The automatic shut down is effective in the "Standard mode" and the "Online mode", how-

ever not in the "Database mode".

4.2 Standard mode

The reader is set to the "Standard mode" when it is shipped from the factory. This mode allows read-

ing of different types of transponders and the code is shown in the display. At the same time the code

of each successfully read transponder is stored in the built in memory. This memory may be operated

in two different settings , as described in chapter 4.5 in detail. In the "Standard mode" the reader

shuts down after a certain period automatically, in order to save battery power.

4.3 Start reading

From the Stand-by mode the reading cycle is initiated by pressing the blue main button. After that the

display shows in its upper line the number of data records already stored; in its lower line the status

message: Scanning.... The reader now tries to read a transponder within the next 5s.

The reader emits a beep, as soon as the transponder code has been read. As a result, the code is shown

on the display. If within a time interval of 5s no transponder could be read, the reader switches off the

reading cycle and returns to Stand-by. On the display appears: “ --- No Tag --- ”.

Note: If the battery is low and has not sufficient power the contrast of the display will fail especially

during the scan process. It is recommended to have a second battery in reserve.

4.4 Data storage

In the initial setting -ex works- the reader stores the data records in the following way:

Whenever a transponder code has been read, the entire memory will be checked whether this data rec-

ord has been stored already. If this is not the case, the record will be added to the database. The read-

er emits a single beep.

Table des matières

Manuels Lecteur de cartes populaires d'autres marques

Lindy

Lindy 43185 Manuel utilisateur

Lindy

Lindy 43185 Manuel utilisateur

ViziT

ViziT RD-4F Manuel utilisateur

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manuel utilisateur

AVID ID

AVID ID AVID1043 Manuel utilisateur

Conrad

Conrad PCMCIA Manuel utilisateur

Rosslare

Rosslare DR-6255 Manuel utilisateur

Lindy

Lindy 51541 Manuel utilisateur

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manuel utilisateur

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manuel utilisateur

ACS

ACS ACR122L Manuel utilisateur

Secukey

Secukey S2-MF Manuel utilisateur

Elecom

Elecom MR-SMC07 series Manuel utilisateur

Alien

Alien ALR-9800 Manuel utilisateur

ACS

ACS ACR310 Manuel utilisateur

Datamars

Datamars R-IN1300 MID Manuel utilisateur

Alarm Lock

Alarm Lock AL-PRE2 Manuel utilisateur

xpr

xpr B100PROX-AH Guide de l'utilisateur