Triple solar M2 360 200 landscape Manuel utilisateur

manual

heat pump panels

triple solar

heating without gas

versie 9-03-2020
S
t
a
n
Index
1. General information........................................................................................ 2
Safety instructions ........................................................................................ 2
Legal requirements, standards and regulations ................................................. 2
Permitted load of the panels........................................................................... 2
Transport reguations ..................................................................................... 2
2. Technical information ..................................................................................... 3
Measures ..................................................................................................... 3
Size, weight and material .............................................................................. 4
3. Placement of the panel field ........................................................................... 4
Inclination angle on flat roof........................................................................... 4
Space between rows on flat roof ..................................................................... 4
4. Assembly parts ............................................................................................... 5
Standard components ................................................................................... 5
Pitched roof mounting parts, tiled roof............................................................. 6
Flat roof mounting parts ................................................................................ 6
Hydraulic, electrical and other components ...................................................... 7
5. Preparation for pitched roof, tiled roof ........................................................... 8
Aligning panels and installing roof brackets ...................................................... 8
6. Preparation for a flat roof ............................................................................. 12
7. Installation of the panels.............................................................................. 13
Placing the TS clamping profile ......................................................................13
Mounting of the panels .................................................................................14
Mounting the TS clamping profile ...................................................................16
Mounting connecting hoses and/or connection plugs ........................................17
Connecting the PV panels electrically..............................................................17
8. Connecting the pipes .................................................................................... 19
Material and position ....................................................................................19
Fittings .......................................................................................................20
Pipe diameters of source pipes ......................................................................22
Hydraulic plan .............................................................................................22
Filling medium.............................................................................................23
Installing the expansion vessel ......................................................................23
Connecting thermostatic mixing valve ............................................................23
Insulation ...................................................................................................24
Micro air bubble separator ............................................................................24
9. Finishing a pitched roof ................................................................................ 25
10. Activating the system ................................................................................. 26
Testing leak tightness, filling and system pressure .........................................26
Commissioning the heat pump (IBS) ............................................................27
11. Maintenance ............................................................................................... 28
12. Warranty conditions ................................................................................... 28

Triple Solar assembly instruction PVT heat pump panels March 2020

1. General information

Safety instructions

Your basic equipment should consist of at least:

-safety shoes

- helmet

- safety goggles

- cut-resistant gloves

Attach ladders at an angle of 65 - 75 ° only to safe supports and also secure them against sinking,

slipping or falling over. Use ladders only to bridge a maximum difference in height of 5m. Do not use

damaged or repaired ladders. The ladder must protrude 1 metre above the roof edge.

In the traffic zone, secure the site with barriers, especially below the installation location.

Use impact or fall protection on the roof or ropes with harnesses attached to a fixed anchor point.

Electrical wires that can be touched by heat pump panels must be disconnected or covered by the

responsible electricity company.

Necessary safety distances from power cables to the worker's working area:

- safety beam 1 m to 1 kV voltage

- safety beam 3 m to 110 kV voltage

- safety beam 4 m to 220 kV voltage

- safety beam 5 m to 380 kV voltage

Note the large wind surface area of heat pump panels and accessories. Provide a stable surface during

installation. Stop the installation in case of strong gusts of wind.

Provide lightning protection during assembly in accordance with building regulations.

Legal requirements, standards and regulations

The installation must comply with local conditions, local regulations and, last but not least, technical

rules.

The relevant safety regulations (e.g. NEN1010) must be observed.

The mounting material supplied by Triple Solar is TÜV approved and in accordance with Eurocode EN

1991-1-4. Manufacturer's instructions must be observed in order to make a warranty claim.

Permitted load of the panels

The heat pump panels are designed for the following permitted loads:

- Pressure load (Snow, Wind): 5400 Pa

- Tensile load (Wind): 2400 Pa

When using third-party mounting systems, these values must be observed.

When using the mounting materials supplied by Triple Solar, the above values apply.

Transport reguations

The heat pump panels may only be supported on the frame via the profiles on the short side of the

panel.

The hydraulic connections as well as the collection tubes and fin packages may not be used to lift the

heat pump panel. Aids such as lifting straps, etc. may not be attached to the pipes.

As long as the heat pump panels are stored, the caps remain on the connections to prevent dirt from

getting into the pipes.

Triple Solar assembly instruction PVT heat pump panels March 2020

2. Technical information

Measures

Model: M2 360 200 landscape

Model: M2 300 165 landscape

Figure 2.1-a heat pump panel type M2 360 200 landscape

Figure 2.1-b heat pump panel type M2 300 200 landscape

Triple Solar assembly instruction PVT heat pump panels March 2020

Size, weight and material

size

unity

M2 360 200

landscape

M2 300 165

landscape

Outside dimensions

1987 x 995

1668 x 995

Height

PV size

1945 x 984

1648 x 984

Weight (empty / full)

28 / 32

23 / 27

PV power

360

300

Gross surface

1,98

1,65

materials

PV-panel

Glass

Heat exchanger tubes

Copper

Heat exchanger fins

Aluminium

Finishing

Kataforese

3. Placement of the panel field

Inclination angle on flat roof

Mount heat pump panels at an angle between 10° and 30°.

(Areas with a lot of snow: install the heat pump panels at an angle between 30° and 90°)

Space between rows on flat roof

The greater the row spacing, the less shadow there is. For the electrical output of the installation it is

important to have as little shading as possible, see figure 3.2-a.

Triple Solar assembly instruction PVT heat pump panels March 2020

Sufficient distance between rows is also important in relation to walking space during installation and

repairs. Also take into account the space required for pipe work.

4. Assembly parts

Standard components

Art.nr.

Description

Specification

Image

322101

324201

Mounting rail

2120 mm

4200 mm

330101

Mounting rail

connector

Aluminium with M8 flange nuts

310300

TS clamping profile

slide connector

Assembly of plastic and stainless steel

parts

310101

TS end clamp

Aluminium

310200

TS middle clamp

Aluminium

331240

Hammerhead bolt

M8x40 stainless steel

331600

Flange nut

M8 stainless steel

311000

TS clamping profile

Aluminium

Figure 3.2-a recommended flat roof row distances, by type M2 360 200 landscape panels

Triple Solar assembly instruction PVT heat pump panels March 2020

410500

TS retaining clip

Stainless steel

(for connecting plugs and end plugs)

Pitched roof mounting parts, tiled roof

Additional components required for pitched roof installation

Art.nr

Description

Specification

Aantal

Image

300231

Roof bracket with foot

Multi-adjustable, incl.

cross-connector

4x per panel

336200

Screw

7,0x50 stainless steel

(TX30)

2x per roof bracket

Flat roof mounting parts

Additional components required for flat roof installation:

Art.nr

Description

Specification

Aantal

Image

300510

Flat roof frames first

panel south, per row

Sunbeam Universal

1x per panel

Zie figure 4.3-a

300520

Flat roof frames

supplementary panel

south, per row

Sunbeam Universal

1x per panel

300530

Flat roof frames first

panel east/west, per

row

Sunbeam Symmetrical

1x per panel

300540

Flat roof frames

supplementary panel

east/west, per row

Sunbeam Symmetrical

1x per panel

330250

Cross connector

Aluminium

For fastening mounting

rail on Sunbeam flat

roof frames

4x per #300510

2x per #300520

4x per #300530

2x per #300540

Figure 4.3-a Sunbeam frame for flat roof

Triple Solar assembly instruction PVT heat pump panels March 2020

Hydraulic, electrical and other components

430010

Valve

3/4" inside/outside

500000

Thermostatic

mixing valve

1” outside DN25

500200

Flush and fill

connection set

1” inside DN25

500100

Expansion vessel

18 L

500150

Expansion vessel

connection group

Including automatic air vent, pressure

gauge and pressure relief valve 3 bar

800010

TS crane grease

25 gram

610015

PV cable

0,4 meter

411000

TS connecting hose

Stainless steel, with double o-ring

410300

TS connection plug

¾” outside with double o-ring

410200

TS end plug with

air vent

With double o-ring

Triple Solar assembly instruction PVT heat pump panels March 2020

5. Preparation for pitched roof, tiled roof

Attention:

See also the Wagner assembly instruction film on the Triple Solar website.

Aligning panels and installing roof brackets

Each panel is supported by two horizontal mounting rails. These are positioned parallel to each other,

see figure 5.1-a. It is recommended to plan the configuration of panels, pipes and hoses before starting

the installation.

Four roof brackets are required per panel. 2 Screws are included per roof bracket; 7,0x50 stainless steel

Attention:

The dimensions in figure 5.1-a are critical. If they are not respected, the warranty on the panels

will be invalid.

•Start with the lower rail of the lower row of panels. Place the outermost roof bracket at 450 mm

from the edge of the panel field. Spread the rest of the roof brackets evenly with 1000 mm

distance between them. Maximum distance is 1600mm depending on the size of the field, see

figure 5.1-b.

Figure 5.1-a sloping roof alignment diagram (dimensions in mm) The lengths can differ per type of panel.

Triple Solar assembly instruction PVT heat pump panels March 2020

Figure 5.1-b Pitched roof alignment diagram (dimensions in mm) The lengths can differ per

type of panel.

•Attach the roof brackets if necessary with extra underlayment wood to get the correct height

and/or for a more solid mounting.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels triple solar Panneau solaire

triple solar

triple solar 101125 Manuel utilisateur

Manuels Panneau solaire populaires d'autres marques

Navitron

Navitron HFC-2 Manuel utilisateur

AXITEC

AXITEC 60-CELL Manuel utilisateur

thermital

thermital TSOL 20 N BLU Manuel utilisateur

AZO Digital

AZO Digital MPPT-3000 Manuel utilisateur

Clenergy

Clenergy PV-ezRack SolarTripod Manuel utilisateur

Beretta

Beretta SCF-20N Manuel utilisateur

moovo

moovo KSM001 Manuel du produit

solarwatt

solarwatt EasyIn 60M Series Manuel utilisateur

Solarland

Solarland Portable Series Manuel

Ubiquiti

Ubiquiti sunMAX Manuel utilisateur

Lippert

Lippert Furrion FSFP37MW-BL Manuel utilisateur

Sonnenkraft

Sonnenkraft GK5-HP Manuel utilisateur

REC

REC TwinPeak 2S Mono 72 Series Manuel utilisateur

Sunforce

Sunforce 50039 Manuel utilisateur

Flexsolar

Flexsolar C100 Mode d’emploi

Süd Solar

Süd Solar 03005 Manuel utilisateur

Kodak

Kodak SP21 Manuel utilisateur

Carmanah

Carmanah Go Power! Solar Flex GP-FLEX-30 Manuel utilisateur

triple solar M2 360 200 landscape Manuel utilisateur

Manuels Panneau solaire populaires d'autres marques