Trine 206-3 Manuel utilisateur
206-3 -- Wireless
Entry/Exit Signal Kit
Instruction Sheet
Troubleshooting
PHONE: (203) 730-1756
FAX: (203) 730-1781
2 PARKLAWN DR. STE F, BETHEL, CT 06801
customerser[email protected]
www.trineonline.com
NOTE: This unit is NOT compatible with 206-3
units sold before December, 2014
For swinging doors
align the transmitter
arrow to the bottom
of the magnet
as shown.
V. 16.0504
• Transmitter
communicates with the
chime wirelessly.
• Can be used with swinging
or sliding doors
• Chime plugs into a
standard electric outlet
• Includes a Door Magnet
Spacer and all the
mounting screws
• Transmitter range: 100’
• Three High Quality Chime
tunes
• (1) 12V A23 Battery is
included
A. Problem: Chime does not ring one time
and stop.
1a. Possible Cause: Sensor battery is not
installed properly.
1b. Fix: Make sure battery is installed
according to the diagram inside sensor.
2a. Possible Cause: Sensor battery is dead.
2b. Fix: Replace sensor battery.
3a. Possible Cause: Chime is not receiving
power
3b. Fix: Make sure the plug-in chime has
power
4a. Possible Cause: Sensor & Chime are not
synced
4b. Fix: Re-try syncing process
- Unplug chime
- Ensure switch 1 on both chime and
sensor is set to OFF
- Wait 30 Seconds
- Press and hold the “TEST” button
inside the sensor within 20 seconds after
plugging in chime. When the “Ding-dong”
tune is played, the sensor is synced with
the chime.
B. Problem: Battery seems okay but the chime
does not work after installation.
1a. Possible Cause: Chime or Transmitter is
mounted on metal or near metal studs.
(metal reduces range of unit)
1b. Fix: Use a 1/4” to 1/2” wooden shim to to
move Transmitter away from metal surface.
Move Chime to another wall outlet.
2a. Possible Cause: Chime or Transmitter is
mounted near concrete. (concrete reduces
range of unit)
2b. Fix: Move away from concrete
3a. Possible Cause: Chime & Transmitter are
installed too far apart (over 100 feet)
3b. Fix: relocate pieces closer to one another.
C. Problem: Chime sounds when not intended.
1. Possible Cause: Chime or Transmitter is
receiving interference
2. Fix: Follow A. Problem - 4b. Fix to Unsync the
unit
- Follow A. Problem - 4b. Fix Again to
Resync the units
- If problem persists move Chime or
Transmitter to another location to reduce
interference.
FEATURES:
NOTE: This unit is NOT
compatible with 206-3
units sold before
December, 2014
What’s Included:
Installation:
Chime
(Plug in)
**Note: Arrows do not line up**
**Position as shown**
Door
Magnet
Door
Magnet
Wireless
Transmitter
Spacer
Mounting
Screws
Chime Selection Chart
Transmitter
& Trigger
Screws
Magnet
Spacer
Magnet
Spacer
1. Plug the chime on an electric outlet within the
range of the transmitter. It will take 30 seconds for
the electronics to initialize.
2. Take off the back cover of the transmitter unit to
find the programming switches.
3. After the chime initializes, push the “Test Button”
on the transmitter for 20 seconds so the chime can
pair with the transmitter.
Note:
A “Ding-Dong” sound from the chime indicates that
the transmitter has been successfully mated with the
chime.
A single “Ding” from the chime indicates that the
transmitter memory was erased.
4. Select the desired chime sound. See the selection
chart for the dip switch combinations.
5. Mount the transmitter unit on to the door frame.
6. ** Align the door magnet with the transmitter -
see door positioning above** Use the door magnet
spacer if the door is recessed too far from the frame.
7. Test the completed installation. Refer to the trou-
bleshooting section if the installation does not work.
Transmitter Chime
Test
Button
Transmitter
Dip Switch
Transmitter
Switch 2 - ON
Switch 2 - OFF
Switch 2 - OFF
Switch 2 - ON
Tune
Ding
Ding-Dong
Ding-Dong
Westminster
Chime
Switch 2 - ON
Switch 2 - OFF
Switch 2 - OFF
Switch 2 - ON
Autres manuels Trine Système de sécurité
Manuels Système de sécurité populaires d'autres marques
EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur
Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur
Siren
Siren LED GSM Manuel utilisateur
Detection Systems
Detection Systems 7090i Instructions de montage
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur
Siemens
Siemens FDM273 Manuel utilisateur