Trikdis FLEXi SP3 Manuel utilisateur

www.trikdis.com UAB Trikdis Draugystes g. 17, LT-51229 Kaunas, Lithuania +370 37 408 040 [email protected]

Security control panel

FLEXi SP3

User manual

(Protegus, Paradox keypads)

August 2020

www.trikdis.com 2August 2020

FLEXi SP3 user manual

Attention!

Read this user manual carefully.

A representative from the company installing the alarm system will explain which functions of the FLEXi SP3 security module

must be activated to ensure proper protection of the premises.

Trademarks and patents

Other trade names used in this document may be trademarks or registered

trademarks belonging to their respective manufacturers or retailers.

Manufacturer

UAB „Trikdis“,

Draugystes g. 17, LT-51229 Kaunas, Lithuania

Version

This document is applicable to FLEXi SP3 security modules with firmware

version v1.00 and up.

Certification

CE marking

European Union directives

2004/108/EC (EMC directive)

1999/5/EC (conformity directive)

Contact information for inquiries

Contact information can be found on the website www.trikdis.com

 
www.trikdis.com 3August 2020 
FLEXi SP3 user manual 
 
Contents 
1ABOUT YOUR ALARM SYSTEM ...................................................................................................................................... 4 
2MAIN TECHNICAL SPECIFICATIONS................................................................................................................................ 4 
3POWERING THE EQUIPMENT......................................................................................................................................... 4 
4GENERAL OPERATION OF THE ALARM SYSTEM ............................................................................................................. 4 
4.1 TRANSMISSION OF ALERT MESSAGES ..................................................................................................................................... 4 
4.2 ALARM SYSTEM OPERATION MODES ...................................................................................................................................... 5 
4.3CONTROL OF THE ALARM SYSTEM ......................................................................................................................................... 5 
4.4 CONTROL ACCESS .............................................................................................................................................................. 5 
4.5 SECURITY FUNCTIONS......................................................................................................................................................... 5 
4.6 ADDITIONAL FUNCTIONS..................................................................................................................................................... 6 
5CONTROLLING THE ALARM............................................................................................................................................ 6 
5.1 CONTROLLING THE ALARM WITH A SK232LED B/W KEYPAD .................................................................................................... 6 
5.2 CONTROLLING THE ALARM WITH A PARADOX KEYPAD ............................................................................................................... 7 
5.3 QUICK ARMING/DISARMING OF THE ALARM SYSTEM................................................................................................................. 9 
5.4 ARMING THE ALARM IN ARM MODE..................................................................................................................................... 9 
5.5 ARMING THE ALARM IN STAY MODE..................................................................................................................................... 9 
5.6 ARMING THE ALARM IN SLEEP MODE ................................................................................................................................... 9 
5.7 DISARMING THE ALARM (OFF MODE) ................................................................................................................................. 10 
5.7.1 Switching off the alarm after it has been activated............................................................................................... 10 
5.8 TEMPORARY ZONE BYPASS (BYPASS FUNCTION)..................................................................................................................... 10 
5.9 VIEWING AND CLEARING ALARM ACTIVATION MEMORY ........................................................................................................... 10 
5.10 RESETTING FIRE (SMOKE)SENSORS...................................................................................................................................... 11 
5.11 EMERGENCY CALL BUTTONS............................................................................................................................................... 11 
5.12 TROUBLESHOOTING THE ALARM SYSTEM .............................................................................................................................. 11 
5.13 PROGRAMMING USER CONTROL CODES................................................................................................................................ 12 
5.13.1 Changing the administrator code ...................................................................................................................... 12 
5.13.2 Entering new User codes ................................................................................................................................... 12 
5.13.3 Editing User codes ............................................................................................................................................. 12 
5.13.4 Viewing partition statuses ................................................................................................................................. 12 
5.13.5 Deleting User codes ........................................................................................................................................... 12 
5.13.6 Duress code........................................................................................................................................................ 13 
6CONTROL USING IBUTTON KEYS.................................................................................................................................. 13 
7CONTROL USING RFID CARDS (TAGS) .......................................................................................................................... 13 
8CONTROL USING PHONE CALLS ................................................................................................................................... 13 
9CONTROL USING SMS MESSAGES................................................................................................................................ 14 
 
 

www.trikdis.com 4August 2020

FLEXi SP3 user manual

1About your alarm system

The FLEXi SP3 control panel is part of a premise security and fire alarm system. It performs sensor signal processing and

signalizer control and has integrated GSM and WiFi modems that can transmit alert messages to the central monitoring station

and to users’ mobile phones.

Representatives of the company that installed the alarm system will explain the details on the operation, configuration and

control of Your alarm system.

2Main technical specifications

Number of security zones

10 zones (20 zones if using ATZ), can be expanded to up to 32 zones using

expanders

Number of partitions

Up to 8

Ways of alerting about danger

Sound, indoor and/or outdoor sirens. Strobe lights. Transmission of messages

to central monitoring station and/or to users

Alert messages are transmitted

To central monitoring station via GPRS to two addresses and/or via SMS

messages

To 8 user mobile phones via SMS messages

Safety requirements

Meets safety requirements of the EN 60950 standard

User codes for control

Up to 40 user control codes; allowed number of different iButton keys or RFID

cards –up to 40

Resistance to environmental influences

class

Meets demands of standard EN 50131 for Class II environmental classification

Operating conditions

Temperature from -10 °C to +50 °C, relative humidity 80% at +20°C, no

condensation

Main power supply

230 V 50 Hz single-phase AC power network (through a step-down power

transformer). Power consumption no higher than 40 W

Backup power supply

12 V / 7 Ah battery. Current consumption no higher than 0,5 A

3Powering the equipment

The control panel is powered by an AC power network, or, in case it fails, by a backup battery. When an AC power network is

available, the battery is charged and kept in standby mode. The time of operation using the backup battery is limited and

depends on the amount of current used by the alarm system. A voltage of 12 V is required to power additional equipment.

4General operation of the alarm system

The security-fire alarm system consists of a signal processing board (the control panel), installed in a casing along with a step-

down power transformer and backup power supply battery, with intrusion, break-in, fire and other sensors, sound and light

signalers and control equipment connected to it.

If the alarm system is armed and any of the sensors are triggered, sound and light signalizers are turned on, and, if set, alert

messages are sent to the central monitoring station and to users. If the alarm is disarmed, it will only react to the triggering of

sensors that are set to operate continuously.

4.1 Transmission of alert messages

Alert messages can be transmitted to the CMS (central monitoring station) and/or to users. Messages are sent via the selected

connectivity channels, first to the CMS and only then to users via Protegus, SMS messages and/or phone calls.

www.trikdis.com 5August 2020

FLEXi SP3 user manual

4.2 Alarm system operation modes

Mode

Description

OFF (DISARM)

In this mode, only some of the zones are protected. The alarm will only react to events in zones

set to Fire, 24 hour, Silent 24h.

ARM

In this mode, all zones are protected. The alarm will react to all possible events.

STAY

In this mode, a part of the zones is protected, but movement is allowed in zones set to Interior

STAY and Instant STAY. If the alarm system is operating in this mode and a Delay zone is

violated, the alarm will activate only after the entry time has elapsed.

SLEEP

In this mode, a part of the zones is protected, but movement is allowed in zones set to Interior

STAY and Instant STAY. If the alarm system is operating in this mode and a Delay zone is

violated, the alarm will activate immediately.

4.3 Control of the alarm system

The alarm system can be controlled using the following devices:

•Trikdis keypad Protegus SK232LED W/B;

•Paradox keypads K32+, K32LED, K636, K10LED V/H, K35, TM50, TM70;

•Crow keypads CR-16, CR-LCD;

•iButton keys;

•RFID cards;

•Electric switch, by changing the state of the zone selected by the keyswitch;

•Telephone (by phone call or by sending an SMS message with specific contents);

•Protegus app;

•Remote command from monitoring station.

4.4 Control access

Control codes are used to give different users different access levels for controlling the alarm system. The user control codes

are four digits long. When choosing and entering control codes, only numbers from 0 to 9 are used, other symbols are not

available.

Types of alarm system control codes:

•Administrator code –a six-digit combination (default code - 123456). There is only one administrator code. It cannot be

deleted, but it can be changed. The Administrator code allows to add or delete other users’ control codes. The

Administrator code cannot arm/disarm the alarm system;

•User code –a four-digit combination for arming/disarming the alarm system and for temporarily bypassing security

zones. It is recommended to assign every user a personal alarm control code. The memory of the FLEXi SP3 module can

store up to 40 user codes;

•SMS password –six-digit combination for controlling the alarm system via SMS messages (default code - 123456).

4.5 Security functions

Name

Description

Bypass

Temporarily (for one arming of the alarm system) bypasses a security zone when changing the alarm

status. The function is used when the alarm needs to be armed, but a zone is malfunctioning and the

fault cannot be easily repaired.

Bell Squawk

The module can use a short siren signal to warn about the arming and disarming of the premise alarm

system.

Chime

When the alarm is disarmed, the module can warn that a zone is being violated by turning on the

keypad buzzer and/or a specially programmed PGM output.

www.trikdis.com 6August 2020

FLEXi SP3 user manual

Name

Description

Re-ARM

Used to protect against accidental disarming of the alarm. If the alarm was disarmed via phone call, but

the Delay zone was not violated, the alarm will automatically return to its previous security mode after

the Entry Delay time passes.

4.6 Additional functions

Name

Description

Temperature

measurement

Up to 8 temperature sensors DS18B20, DS18S20 or one temperature and humidity sensor AM2301 can

be connected to the FLEXi SP3 module. Intervals of permitted temperatures can be set for each of

them individually. If the temperature changes beyond the set interval, an event message will be

formed and sent to users.

Remote control of

devices

Additional electronic devices can be connected to the FLEXi SP3 security module’s programmable open

collector outputs and can be controlled remotely.

5Controlling the alarm

5.1 Controlling the alarm with a SK232LED B/W keypad

The Trikdis keypad SK232LED B/W for alarm system control displays the states of 32 zones and 2 partitions.

Buttons for setting operation modes and entering numbers

Button

Description

A constantly glowing button means the alarm system is powered from the AC power network, and a

blinking button shows a battery fault. The button is off –the power voltage supply is off or the system is

operating using the battery. The button is also used for editing control codes and for resetting fire

sensors.

www.trikdis.com 7August 2020

FLEXi SP3 user manual

Button

Description

MEM

A constantly glowing button shows that in memory there is new information about the alarm being

triggered, and a blinking button shows that the keypad is operating in MEM mode. The button is also

used for choosing the memory viewing mode.

BYP

A constantly glowing button means that there are temporarily bypassed zones, and a blinking button

shows the keypad is operating in BYP mode. The button is also used for selecting temporary bypass

mode.

TRB

A constantly glowing button means that operational trouble has been recorded, and a blinking button

shows that the keypad is operating in TBL mode. The button is also used for selecting trouble viewing

mode.

1, 2 ...9, 0

Buttons for entering numbers.

Button for exiting modes and clearing values.

Button for confirming the specified choice.

ARM

Button for turning on full security mode ARM.

SLEEP

Button for turning on SLEEP mode.

STAY

Button for turning on STAY mode.

OFF

Button for turning on OFF (DISARM) mode.

Note:

1. To turn off programming mode or delete an incorrectly entered value, press the [C] button.

2. If at least one zone is violated, it will not be possible to arm the alarm system (if the FORCE property

is not assigned to the violated zones).

5.2 Controlling the alarm with a Paradox keypad

The Paradox K10LED V/H keypad for alarm system control displays the states of 10 zones and 2 partitions.

The Paradox K636 keypad for alarm system control displays the states of 10 zones and 1 partition.

www.trikdis.com 8August 2020

FLEXi SP3 user manual

Paradox keypads K32LED, K32+ for alarm system control display the states of 32 zones and 2 partitions.

The Paradox K35 keypad for alarm system control displays the states of 32 zones and 2 partitions.

Buttons for setting operation modes and entering numbers

Button

Description

Button for resetting fire sensors.

MEM

A constantly glowing button shows that in memory there is new information about the alarm being

triggered, and a blinking button shows that the keypad is operating in MEM mode. The button is also

used for choosing the memory viewing mode.

BYP

A constantly glowing button means that there are temporarily bypassed zones, and a blinking button

shows the keypad is operating in BYP mode. The button is also used for selecting temporary bypass

mode.

TBL

A constantly glowing button means that operational trouble has been recorded, and a blinking button

shows that the keypad is operating in TBL mode. The button is also used for selecting trouble viewing

mode.

1, 2 ...9, 0

Buttons for entering numbers.

CLEAR

Button for exiting modes and clearing values.

ENTER

Button for confirming the specified choice.

ARM

Button for turning on full security mode ARM.

SLEEP

Button for turning on SLEEP mode.

STAY

Button for turning on STAY mode.

OFF

Button for turning on OFF (DISARM) mode.

Power voltage indicator. Constantly glowing –power voltage is turned on. Blinking –battery fault. Off

–the power voltage source is off or the system is operating from the battery.

Note:

1. To turn off programming mode or delete an incorrectly entered value, press the [CLEAR] button.

www.trikdis.com 9August 2020

FLEXi SP3 user manual

2. If at least one zone is violated, it will not be possible to arm the alarm system (if the FORCE property

is not assigned to the violated zones).

5.3 Quick arming/disarming of the alarm system

Arming/disarming the alarm system using a code when the security system has STAY zones.

Security modes ARM, STAY and SLEEP are switched to OFF/DISARM, and OFF/DISARM is switched to ARM or STAY mode.

Changing the security mode:

1. Enter [User code].

a. If the system only has one partition, skip step 2. If the system has more than one partition, the numbers of the

partitions that the user is allowed to change the modes of will light up on the keypad.

2. Press the numbers of the chosen partitions.

3. Partitions that were in ARM, STAY and SLEEP modes will switch to OFF/DISARM mode.

a. When the alarm is off, the [OFF] indicator is glowing.

b. If the Bell Squawk function is enabled, the siren will activate twice for short periods of time as the alarm switches

off.

4. Exit delay time will be counted down for partitions that were in OFF/DISARM mode. If a Delay zone is violated during

the countdown, ARM mode will switch on, and if a Delay zone is not violated, STAY mode will switch on.

a. The respective keypad indicator ([ARM] or [STAY]) will light up.

b. If the Bell Squawk function is enabled, the siren will activate once for a short period of time as the alarm switches

on.

5.4 Arming the alarm in ARM mode

To turn on ARM security mode for an alarm system that is divided into multiple partitions:

1. Press the keypad button [ARM].

2. Enter the [User code] using the keypad.

3. Press the buttons with the numbers of the partitions you want to control.

4. Confirm your selection by pressing the [OK] (or [ENTER]) button.

5. Before the Exit Delay time runs out, leave the premises and close the door.

a. During the Exit Delay time countdown, the keyboard indicator [ARM] will blink, and when the alarm is armed, it will

glow constantly.

b. If the Bell Squawk function is enabled, the siren will activate once for a short period of time as the alarm switches

on.

5.5 Arming the alarm in STAY mode

To turn on STAY security mode for an alarm system that is divided into multiple partitions:

1. Press the keypad button [STAY].

2. Enter the [User code] using the keypad.

3. Press the buttons with the numbers of the partitions you want to control.

4. Confirm your selection by pressing the [OK] (or [ENTER]) button.

5. The keypad indicator [STAY] will light up.

a. If the Bell Squawk function is enabled, the siren will activate once for a short period of time as the alarm switches

on.

Note:

STAY mode is unavailable unless at least one zone is set to Interior STAY or Instant STAY.

5.6 Arming the alarm in SLEEP mode

To turn on SLEEP security mode for an alarm system that is divided into multiple partitions:

1. Press the keypad button [SLEEP].

www.trikdis.com 10 August 2020

FLEXi SP3 user manual

2. Enter the [User code] using the keypad.

3. Press the buttons with the numbers of the partitions you want to control.

4. Confirm your selection by pressing the [OK] (or [ENTER]) button.

5. The keypad indicator [SLEEP] will begin to glow.

a. If the Bell Squawk function is enabled, the siren will activate once for a short period of time as the alarm switches

on.

5.7 Disarming the alarm (OFF mode)

When the premises are secured in ARM or STAY mode, the countdown of the Entry Delay time will begin if anyone enters the

premises. You must disarm the alarm before the time runs out.

To switch off protection mode (switch on OFF / DISARM mode):

1. Press the keypad button [OFF].

2. Enter the [User code] using the keypad.

a. If the system has only one partition, skip steps 3 and 4.

3. Press the buttons with the numbers of the partitions you want to control.

4. Confirm your selection by pressing the [OK] (or [ENTER]) button.

a. When the alarm is off, the indicator [OFF] lights up.

b. If the Bell Squawk function is enabled, the siren will activate twice for a short period of time as the alarm switches

off.

5.7.1 Switching off the alarm after it has been activated

To switch off the alarm:

1. Enter the [User code].

a. If the system has only one partition, skip steps 2 and 3.

2. Press the buttons with the numbers of the partitions you want to control.

3. Confirm your selection by pressing the [OK] (or [ENTER]) button.

a. When the alarm is off, the indicator [OFF] lights up.

b. If the Bell Squawk function is enabled, the siren will activate twice for a short period of time as the alarm switches

off.

c. The [MEM] indicator will light up and violated zones will start blinking. Press [MEM] and then [C] (or [CLEAR]) to stop

the blinking of the violated zones.

5.8 Temporary zone bypass (Bypass function)

To switch on the Bypass function:

1. Press the [BYPASS] button on the keypad.

2. Enter the [User code].

a. The BYP indicator will start blinking.

3. Enter the two-digit numbers of the zones that you want to bypass.

4. Confirm your selection by pressing the [OK] (or [ENTER]) button.

5. The BYP indicator will start glowing.

To switch off the Bypass function, repeat the same steps as above.

5.9 Viewing and clearing alarm activation memory

When the alarm is activated, the indicator [MEM] starts glowing. To find out the reason of the alarm activation:

1. Press the [MEM] button on the keypad.

2. The glowing numbers indicate which zones caused the alarm to activate.

3. To exit this mode, press the [C] (or [CLEAR]) button.

Autres manuels pour FLEXi SP3

Table des matières

Autres manuels Trikdis Panneau de contrôle

Trikdis

Trikdis FLEXi SP3 Manuel utilisateur

Trikdis

Trikdis CG17 Manuel utilisateur

Trikdis

Trikdis FLEXi SP3 Instructions de montage

Trikdis

Trikdis FLEXi SP3 Manuel utilisateur

Trikdis

Trikdis SP231 Manuel utilisateur

Trikdis

Trikdis SP231 Instructions de montage

Manuels Panneau de contrôle populaires d'autres marques

RDZ

RDZ PC-HRX Manuel utilisateur

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuel technique

Efka

Efka Variocontrol V810 Manuel utilisateur

Cebora

Cebora 208-10 Manuel utilisateur

AMX

AMX AutoPatch CP-15 Manuel utilisateur

Satel

Satel CA-6 KLED-S Manuel utilisateur

Evolution

Evolution IQ plus 800 Manuel utilisateur

Fagor

Fagor 8040 TCO CNC Manuel utilisateur

Trane

Trane ComfortLink II XL950 Control Manuel utilisateur

AKO

AKO PROCool AKO-17635-2 Manuel utilisateur

ABB

ABB 6136/30M-101 Manuel utilisateur

Telikou

Telikou BK-603 Belt Pack Manuel utilisateur

Mapei

Mapei Mapeheat Thermo Touch Manuel utilisateur

Bosch

Bosch D9412GV4 Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuel utilisateur

Sminn

Sminn BOX L VF1L EI Manuel utilisateur

Balboa

Balboa TP600 Manuel utilisateur

Nice

Nice HSCU1 Caractéristiques techniques