Trident iON Manuel utilisateur
iON
Micromotor
Instruction
Manual
2
Table of Contents
Introduction…………………………………………………… Page 3
Upon Receiving your iON……………………………………... Page 4
Installation…………………………………………………….. Page 4 - 5
Selecting Micromotor Parameters…………………………….. Page 5 –6
Menu Items…………………………………………………… Page 6 –7
Error Messages……………………………………………….. Page 8
Maintenance………………………………………………….. Page 9
Warranty……………………………………………………… Page 9
Precaution……………………………………………………. Page 9
iON Schematic…………………………………………….…. Page 10
Chuck Adjustment/Replacement…………………………….…. Page 11-13
3
INTRODUCTION
Trident Sales Associates thanks you and congratulates you for choosing the iON as your new
Micromotor. The iON was designed and engineered by highly qualified personnel with
many years of experience and expertise in micromotor manufacturing. Its construction
underlines the high standards of quality that have always distinguished our products.
The iON is recognized for the type of main electric motor it utilizes, which operates
according to the latest “brushless” technology used in modern industrial processes.
Unlike traditional motors, this technology allows the motor to operate with direct current
eliminating graphite brushes which are subject to wear and maintenance problems.
Special “unique” features of the iON include:
* High-speed, low-noise bearings
* An adjustable, easily replaceable chuck system
* An ergonomic comfort grip
* Automatic torque compensation adjustment which recovers over 80% of
maximum torque, even at low speeds
* 40,000 rpm of power
* Power overload protection
This instruction manual will help familiarize you with the iON. Please read it carefully.
Keep the manual in a safe place so that it can be consulted whenever necessary. Should you
have any questions please contact:
Trident Sales Associates
195 Basik Drive, Suite 506
Naples, FL 34114
Tel: 561-826-9331
Fax: 561-353-0895
Email: walter@tridentsales.us
4
UPON RECEIVING YOUR iON
Carefully inspect the unit to insure that it has not been damaged in shipping. In the event of
any damage, immediately contact the shipping company to report it.
The Ion 40K Micromotor comes with the following:
* Micromotor
* Control Box
* Foot Pedal
* Foot Pedal Connector
* Power Cord
* Micromotor Stand
* Chuck Tool with Allen Wrench
* Warranty Card
* Instruction Manual
INSTALLATION
Remove all items from the shipping box.
Place the Control Box on the bench in the area where it will be used.
Connect the Micromotor Cord to the round socket at the rear of the Control Box. Secure this
connection in place using the locking ring located at the end of the Micromotor Cord.
Plug the Foot Pedal Connector into the Foot Pedal. Plug the other end of the Foot Pedal
Connector into the rear of the Control Box.
Connect the Power Cord into the rear of the Control Box. Plug the other end of the Power
Cord into a properly grounded 115Volt electrical outlet.
Fit a bur into the chuck of the Micromotor. Turning the front section of the Micromotor
clockwise opens the chuck. Turning the front section of the Micromotor counter clockwise
secures the bur in place.
5
The On/Off power switch is located at the rear of the Control Box. When pressed in the ON
position the display on the Control Box lights up and says: HELLO.
SELECTING MICROMOTOR PARAMETERS
Upon initially turning the iON ON, the display on the front panel of the Control Box says:
HELLO.
After a few seconds the display will indicate the direction of the Motor’s rotation:
Forward > or < Reverse.
The display will then show the rpm, as well as motor rotation: F (forward) or R (reverse).
Motor rotation can be changed anytime by pressing the direction key on the front panel.
ACTIVE KEYS
By depressing the MODE key you can select whether to run the Micromotor at a Variable
Speed or at a Constant Speed. The display will show you which Mode you selected.
Variable Speed - By pressing down on the Foot Pedal you control the speed of the
motor from a minimum of 1000 rpm to a maximum speed that you select…and all
points in between. (The next section will instruct you on how to select the desired
6
rpm).
Constant Speed - By pressing down on the Foot Pedal the motor will start at the
selected rpm and maintain it.
Selecting Speed: By depressing the Speed Keys (up or down) on the front panel you can
select the exact rpm desired. (UP arrow increases rpm, DOWN arrow decreases rpm). Once
you have selected the desired rpm the display shows MEMOR. Your selected rpm has been
saved to memory.
In Variable mode, the rpm value set indicates the maximum permitted motor speed when
depressing the Foot Pedal fully.
In Constant mode, the rpm value set indicates the motor speed when the Foot Pedal is
depressed.
MENU ITEMS
By simultaneously depressing both Speed Keys you can access Menu items.
The Menu items are:
CONTRAST
LANGUAGE
BEEP
EXIT
The SPEED KEYS allow you to scroll through Menu items.
To enter a Menu item simply press the MODE KEY. To exit the menu without making
changes, press the DIRECTION KEY or go to the Menu item EXIT and press MODE.
7
CONTRAST
Using the SPEED KEYS you can adjust the contrast of the display. The value of contrast
displayed is in the range of 00 to 50. It can be increased or decreased in 5 unit increments
50 is minimum contrast.
00 is maximum contrast
To confirm and save the value of the contrast selected press the MODE KEY
Please note that contrast is already preset at the factory for optimum visibility.
LANGUAGE
There is a choice of 4 languages that can be selected:
ENG = English
FRA = French
DEU = German
ITA = Italian
To confirm and save the language selected press MODE.
BEEP
With the SPEED KEYS you can enable (ON) or disable (OFF) the beep. To confirm and
save your selection press MODE.
EXIT
To exit Menu items simply press MODE.
8
ERROR MESSAGES
OVERLOAD - If the Micromotor surpasses or exceeds its maximum safety threshold this
message will appear on the display. Too much force on the Micromotor may be the cause.
Try easing the pressure being applied.
ERROR!!! - This message will appear if the OVERLOAD message is on the display and
extreme force is still being applied. Asafety sensor will signal the ERROR!!! Message and
automatically reduce the power supplied to the Micromotor.
BLOCKED - This message will appear when the motor has been obstructed or prevented
from turning for a prolonged period of time try releasing the Foot Pedal and depressing it
again.
MAINTENANCE
The iON is equipped with high-speed, pre-lubricated bearings. DO NOT LUBRICATE
THESE BEARINGS.
Periodically check the air ducts at the rear of the Micromotor. Air should always exit from
them. Remove any material that may be obstructing these ducts.
Periodically remove the dust protection cap from the front of the Micromotor and clean it
with compressed air. A soft brush may be used to clean the area around the shaft.
If the iON is not being used for a long period of time, it should be stored in a dry area and
covered to protect it from dust and humidity.
9
WARRANTY
The iON is warranted for a full year from date of purchase. If the serial number label is
removed, the warranty becomes null and void.
TECHNICAL INFORMATION
Voltage - 115 Volt (available in 220 Volt upon request)
Fuse - 1.25 Amp
Minimum Speed - 1000 rpm
Maximum Speed - 40,000 rpm
Chuck - 2.35 mm.
PRECAUTION
Never attempt to stop micromotor rotation with any foreign body, or even worse, with your
hands. This will both hazardous and dangerous to you and the micromotor.
10
Table des matières
Autres manuels Trident Équipement industriel
