TRENDnet TE100-PCI Manuel utilisateur
Fiber Ethernet Adapter
User’s Guide 1
檔名: pcifxp.doc
原作者: Carrie Chen
列印時間: 1/31/2003 3:06 PM
Preface
This manual describes how to install and use the Fiber Ethernet
Adapter. This Fiber Adapter allows options of different fiber
connections, such as connector types and segment distance.
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
• Introduction on Fiber Adapter
• Product features
• LEDs functions
• Hardware installation
• Software installation
• Specifications
Fiber Ethernet Adapter
2 User’s Guide
Table of Contents
PREFACE ...............................................................................1
TABLE OF CONTENTS ...........................................................2
PRODUCT OVERVIEW ...........................................................3
FIBER ETHERNET ADAPTER ..........................................................3
PACKAGE CONTENTS....................................................................3
PRODUCT FEATURES ....................................................................4
Driver Support.................................................................................................5
5Software Support..........................................................................................5
LEDs...............................................................................................................6
HARDWARE INSTALLATION .................................................7
INSTALLING FIBER ADAPTER INTO PCI SLOT ..................................7
CONNECTING REMOTE WAKE-UP CABLE .......................................9
CONNECTING TO YOUR NETWORK...............................................10
Cabling Requirements ..................................................................................11
SOFTWARE INSTALLATION.................................................12
DIAGNOSTIC SOFTWARE .............................................................12
About Hardware’s Configuration...................................................................13
Run Diagnostics ...........................................................................................14
LOADING NETWORK DRIVERS......................................................15
Quick List for Supported Network Drivers ....................................................16
SPECIFICATIONS .................................................................17
ORDERING INFORMATION ..................................................18
Fiber Ethernet Adapter
User’s Guide 3
檔名: pcifxp.doc
原作者: Carrie Chen
列印時間: 1/31/2003 3:06 PM
Product Overview
Fiber Ethernet Adapter
Figure 1: Adapters with SC (left) and ST (right) connectors, featuring two LEDs
Package Contents
When you unpack the product package, you shall find the items
listed below. Please inspect the contents, and report any apparent
damage or missing items immediately to our authorized reseller.
Fiber Adapter
User’s Guide
3-wire cable (for Wake On LAN)
Driver Diskette
Fiber Ethernet Adapter
4 User’s Guide
Product Features
• Provide a variety of fiber connections:
SC, ST, MT-RJ or VF-45 connectors for multi-mode, and
SC connector for single-mode
• Support 32-bit Bus Master operation
• PCI bus clock speed range from 16.75 to 40 MHz
• Support Wake-On-LAN (WOL) function and remote
wake-up
• Support half-duplex or full-duplex operation for up to
200Mbps data transfer rate
• Compliant with PCI plug-and-play
• Compliant with IEEE 802.3u 100BASE-FX
• Compliant with PCI Specifications Revision 2.1
• Low CPU utilization
• Status LEDs
Fiber Ethernet Adapter
User’s Guide 5
檔名: pcifxp.doc
原作者: Carrie Chen
列印時間: 1/31/2003 3:06 PM
Driver Support
The Fiber Adapter supports a wide range of drivers for commonly
used network operating systems:
• NDIS2 (DOS, OS/2, LANtastic, WFW3.1…)
• NDIS for Win95, 98, NT 3.51, 4.0, 5.0 WFW3.11
• NetWare ODI driver for DOS, OS/2, and NetWare
3.x, 4.x, 5.0 Server
• SCO Unix driver
• Linux driver
Note: Win2000 driver (RTL8139 A/B/C/8130 Series Adapter)
is bundled with Win2000.
Software Support
• Setup/Diagnostic Program for DOS
(REST8139.EXE in DIAG directory)
Note: RSET8139.EXE is a DOS only application. It may not
run properly under the DOS prompt in Windows.
Fiber Ethernet Adapter
6 User’s Guide
LEDs
cLNK Link
This LED comes on when a network connection is established
successfully.
dACT Activity
This LED flashes when the port is transmitting or receiving data.
LEDs Status Indication
Steady A valid network connection established.
LNK stands for LINK.
LNK
Off Disconnection.
Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
ACT
Off No activity.
Fiber Ethernet Adapter
User’s Guide 7
檔名: pcifxp.doc
原作者: Carrie Chen
列印時間: 1/31/2003 3:06 PM
Hardware Installation
Installing Fiber Adapter into PCI slot
Step 1: Turn off the power to the PC.
Step 2: Remove any metal decorations from your hands and wrists.
Step 3: Remove the cover from your PC.
Step 4: Locate an empty, non-shared bus mastering 32-bit PCI slot and remove
the corresponding backplate. Save the screw for use in Step 6.
<Note>
i. Do not install the Fiber Adapter in a shared PCI slot. Avoid any PCI slot next to
an ISA slot because this is often a shared slot and does not support bus
mastering.
ii. If you are going to install the Remote Wake-Up cable, choose an available
PCI slot most close to the 3-pin Remote Wake-Up connector on the PC
motherboard.
iii. If you have problems in identifying a suitable slot, check your PC
documentation or ask your system administrator for help.
Step 5: Carefully insert the Fiber Adapter into the chosen slot and press firmly
with proper push to ensure it is fully seated in the slot.
Step 6: Secure the Fiber Adapter with the screw you saved in step 4.
<Note>
If you wish to use the Remote Wake-Up function, please complete the
installation in next section “Connecting the Remote Wake-Up Cable” before
proceeding to step 7.
Step 7: Replace the PC cover.
Step 8: Proceed to “Connecting to Your Network” section.
Fiber Ethernet Adapter
8 User’s Guide
Install the FiberAdapterinto the PCIslot
and screwit onto the backplate
Figure 2: Installing Fiber Adapter into 32-bit PCI slot
<Note>
Always ensure the power is cut off before any installation to avoid electric
shock and possible damage to the equipments.
Fiber Ethernet Adapter
User’s Guide 9
檔名: pcifxp.doc
原作者: Carrie Chen
列印時間: 1/31/2003 3:06 PM
Connecting Remote Wake-Up Cable
This is an optional function. Proceed with the installation only
when your PC supports this Remote Wake-Up and you wish to
make use of this function. Please check your Motherboard User’s
Guide for more information.
Step 1: Make sure the power to the PC is off.
Follow Step 1~3 in previous section.
Step 2: Check if the Fiber Adapter is properly installed in a PCI slot.
Step 3: Prepare a Remote Wake-Up cable. Connect the cable from Fiber
Adapter to motherboard connector. Refer to Figure 3 below for details.
Step 4: Replace the PC cover then.
Step 5: Proceed to “Connecting to Your Network” Section.
Connect Remote Wake-Up cable from FiberAdapter
to motherboard connector
Pl u g i n Re m o t e Wa ke - Up c a b l e
to c onnec tor on Fiber Ada pter
Figure 3: Connecting Wake-Up cable
Fiber Ethernet Adapter
10 User’s Guide
Connecting to Your Network
This section describes how to connect the Fiber Adapter to a 100
Mbps fiber-based Ethernet network, which contributes to its
optimal performance.
<Note>
You must connect the Fiber Adapter to the network before installing the
network driver.
Step 1: Remove the protective covers from the Fiber Adapter’s connector.
Step 2: Prepare a network cable with corresponding connectors for the two end
devices, one end to the Fiber Adapter and the other to a 100Mbps fiber
port on the network hub or switch.
Step 3: Connect the network cable to the connector on the Fiber Adapter. This
network cable consists of two individual cables: one for ‘transmission
(TX)’, and the other for ‘reception (RX)’. Refer to Figure 4 for details.
Step 4: Connect the other end of the network cable to a 100BASE-FX hub or a
switch.
<Note>
i. Insert the cable that is connected to the transmit (TX) connector on the Fiber
Adapter into the receive (RX) connector on the network hub or switch.
ii. Insert the cable that is connected to the receive (RX) connector on the Fiber
Adapter into the transmit (TX) connector on the network hub or switch.
Step 5: When the cable is properly connected to two end devices, turn on the
power to the PC.
Step 6: Check the LNK (Link) LED. The LED will come on when the Fiber
Adapter is receiving a good link signal from the connected device, a hub
or switch.
Step 7: Proceed to next section for installing the network driver.
Autres manuels pour TE100-PCI
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels TRENDnet Adaptateur
TRENDnet
TRENDnet TBW-104UB Manuel utilisateur
TRENDnet
TRENDnet TPL-4052E Manuel utilisateur
TRENDnet
TRENDnet TPL-421E Manuel utilisateur
TRENDnet
TRENDnet TEW-441PC - 108Mbps Wireless PC Card... Manuel utilisateur
TRENDnet
TRENDnet TEW-647GA Manuel utilisateur
TRENDnet
TRENDnet TE100-PCBUSR - DATA SHEETS Manuel utilisateur
TRENDnet
TRENDnet TEW-AMBA - Manuel utilisateur
TRENDnet
TRENDnet TBW-104UB Manuel utilisateur
TRENDnet
TRENDnet TEW-648UBM Manuel utilisateur
TRENDnet
TRENDnet TEW-809UB Manuel utilisateur
TRENDnet
TRENDnet TU2-ETG Manuel utilisateur
TRENDnet
TRENDnet TEW-687GA Manuel utilisateur
TRENDnet
TRENDnet TU2-HDMI Manuel utilisateur
TRENDnet
TRENDnet TEW-424UB Manuel utilisateur
TRENDnet
TRENDnet TBW-104UB Manuel utilisateur
TRENDnet
TRENDnet TBW-102UB Manuel utilisateur
TRENDnet
TRENDnet TBW-101UB Manuel utilisateur
TRENDnet
TRENDnet TU-PS2 Manuel utilisateur
TRENDnet
TRENDnet TE100-PCBUSR - DATA SHEETS Manuel utilisateur
TRENDnet
TRENDnet TU3-H2PIE Manuel utilisateur
