TreeGreen EnergyEGG Manuel utilisateur

SOWHAT ISTHE

energyEGG®

The

energyEGG®

is a wireless appliance controller. It makes switching o

appliances in a room - or around the home - simple. It automatically

switches o electrical equipment after you leave the room - saving energy,

time and reducing electric bills.

It has 3 main functions :

ROOM ON/OFF Pressing the Power Button (see Figure 1) switches

ON appliances. Pressing and holding the Power

Button for 2 seconds switches OFF appliances

connected to the Control Adaptor(s) (see Figure 3)

in a room.

Auto Room OFF When a room is empty for a preset time the

energyEGG®

(Figure 2) automatically switches

OFF connected appliances.

HOME OFF Pressing and holding the Power Button for 5 seconds,

while appliances are ON, switches OFF all connected

appliances around a home. Please note that the

maximum range of the

energyEGG®

may vary

depending on the building it is being used in .

Power Indicator

Control Button

Socket

Figure 3 Control Adaptor

Power Button

LED Indicator

Battery Compartment

Smart Motion Sensor

Adjustable Timer on Base

Figure 1 The

energyEGG®

Figure 2 Timer Dial

Timer OFF

Setting

Dial

energyEGG®

Figure 4: Positioning your

energyEGG®

100º

2.5m

3.5m

SET UPINSTRUCTIONS (ROOM CONTROL)

STEP 1 Plug the Control Adaptor into a mains socket, making sure

that the wall socket is switched on. The LED on the Control

STEP 2 Insert the battery into the

energyEGG®

. Press the Power

Button to signal the Control Adaptor. The LED on the

successfully linked with the

energyEGG®

. Test the Control

Adaptor by switching it ON and OFF using the

energyEGG®

Power Button.

STEP 3 When the

energyEGG®

it detects movement. Place your

energyEGG®

(See Figure 4)

up to 2.5m from where you usually sit, around 1m from the

Figure 1) facing you.

Test the

energyEGG®

position by waving your hand and

checking that the

energyEGG® energyEGG®

works best when it is not placed in direct sunlight.

STEP 4 Plug in an appliance or power strip to the Control Adaptor.

Switch OFF appliances by pressing and holding the button

for 2 seconds - the

energyEGG®

will beep twice to indicate

that you can release the button. The 2 second button delay

helps prevent accidental switch OFF.

STEP 5 To connect an additional Control Adaptor to the

energyEGG®

simply repeat these steps. Experiment with the best position

for the

energyEGG®

to signal all Control Adaptors.

Note : To connect an extra

energyEGG®

to a control adaptor, press

and hold the button on the Control Adaptor until the light

Now press the button on the

energyEGG®

to connect it.

SET UP INSTRUCTIONS CONTD...

STEP 6 Set the timer on the base of the

energyEGG®

. Remember

to give yourself enough time to leave the room, make a

cup of tea, and return. This will ensure your appliances are

not inconveniently switched OFF. If you do not want the

energyEGG®

to automatically switch o your appliances

set the Timer Dial to the‘TIMER OFF’ setting (See Figure 2).

TreeGreen recommends using a power strip instead of

severalControl Adaptors when connecting multiple

appliances

Note : If you connect your computer to the

energyEGG®

ensure

that the computer is set to go into sleep mode 5 minutes

before the

energyEGG®

timer setting. So if your computer

is set to go into sleep mode after 10mins, set the

energyEGG®

dial to 15mins. TreeGreen takes no responsibility for

wrong setup or lost data. TreeGreen recommends that you

regularly save and back up your data.

DDITIONAL

EATURES

Auto Your energyEGG® automatically turns OFF appliances

OFF when you forget. It detects when a room is empty and

sends a switch o signal to the Control Adaptor(s) after a

preset time (between 5 and 30 mins). Turn the dial to your

preferred time delay using the intervals on the base as

a reference.

ADDITIONAL FEATURES

CONTD

AUTO OFF The energyEGG® will alert you 1 minute before it switches

Alert anything OFF by beeping and ashing the green light.

This gives you an opportunity to prevent the AUTO OFF

by moving or coming back into the room.

Feedback When the energyEGG® automatically switches appliances

OFF it lets you know by beeping the next time you enter

the room and then ashing the LED green for 1 minute.

HOME OFF Switch o Control Adaptors in dierent rooms using a

single energyEGG® - by pressing the energyEGG® button

for 5s. To set up the HOME OFF function rst ensure that

the energyEGG® is in ON mode (ashes when it detects

movement). Then put each control adaptor you want to

respond to HOME OFF into ‘learn mode’. Now press and

hold the Power button on the energyEGG® for 5 seconds

and release.

Timer OFF If you wish to deactivate the Auto Room OFF of the

energyEGG® and have manual button control only, simply

rotate the dial to the OFF’ setting (see Figure 2).

Battery If your energyEGG® begins to run out of battery power, it

Replacement will beep intermittently for around 5 minutes when

Alert you switch it on. If it starts to beep during operation

and a detected movement does not stop the beeping

then you need to replace the battery.

Reset Control To disconnect a Control Adaptor from all energyEGGs®,

Adaptor press and hold the button on the Adaptor until it ashes

slowly, then ashes quickly.

TROUBLESHOOTING

Problem: ‘My

energyEGG®

switches o appliances while I am in the room’

Solution: Should the

energyEGG®

go into power o mode while you

are in the room, reposition the

energyEGG®

and ensure there

are no obstructions to the eld of view. If you use several

energyEGGs®

, this may be a result of setting up the HOME

OFF function incorrectly - if so, repeat the HOME OFF set up

instructions.

Problem: ‘My

energyEGG®

does not switch o appliances’

Solution: Should the

energyEGG®

fail to switch on/o appliances:

repeat SET UP INSTRUCTIONS. Should the problem persist,

replace the battery. Also Check that the range is within 20m.

Problem: ‘My

energyEGG®

switches my appliances o when I leave the

room to make a cup of tea or go to the bathroom’

Solution: Should the

energyEGG®

switch o appliances when a room is

vacated for a short period then increase the delay setting on

the timer dial.

Problem: ‘I have

energyEGGs®

in several rooms switching o the same

Control Adaptor when I use the ROOM ON/OFF function.’

Solution: Reset the Control Adaptor. To do this press and hold the

button on the Control Adaptor - continue holding the button

until the LED on the Control Adaptor ashes slowly and then

begins to ash quickly. This disconnects the Control Adaptor

and puts it into Learn Mode.

For Solutions to any other Problems, please contact

[email protected]

SAFETY INFORMATION

. Read all instructions before use.

. Do not allow children or people unfamiliar with these instructions to

use your energyEGG®.

. Place your energyEGG® away from sources of heat, liquid and out of

the reach of children.

The following safety recommendations should be followed when

using energyEGG®:

. The energyEGG®

should not be used to control appliances that need

to be left on at all times.

. To protect against re, electric shock and personal injury do not

immerse the energyEGG® unit or Control Adaptor in water or any

other liquid.

. Do not use your energyEGG® outdoors or in the bathroom.

. Do not connect your energyEGG® to any appliance with a damaged

lead or mains plug, or to damaged or faulty appliances.

. Do not disassemble or modify your energyEGG® unit.

. Using the energyEGG®

to control a computer or hard drive may result

in loss of data.

Care and maintenance

. Disconnect components from the power supply before cleaning.

. To clean, use a dry cloth - do not use solvent, abrasive cleaners or water.

. Do not immerse the energyEGG® or Control Adaptor in water or any

other liquid.

Range up to 20m unobstructed

Power Rating (Socket) 13A, 230V

Socket Power Consumption

(in OFF mode) <0.25W

Maximum Load (Socket) 3000W

Transmission Frequency 433.92MHz

Operating Temperature 1ºC - 40ºC

Dimensions EGG : 109 x 65 x 56mm

Control Adaptor : 109 x 55 x 70mm

Weight EGG: 0.101kg, Control Adaptor: 0.138kg

Battery Type PP3 (6F22) Carbon Zinc 9V Battery

Disposal

This product should be handed over to a designated collection point,

such as an authorised collection site for recycling waste electrical and

electronic equipment. For more information about where you can

dispose of waste electrical and electronic equipment, please consult

your local council, waste authority or approved WEEE scheme.

Disposal

Your energyEGG®

comes with a 12 month manufacturer's warranty as

standard. In the event of a physical defect due to material or

workmanship, please contact us, stating where and when you

purchased the device. If you discover a defect covered by this warranty

we will repair or replace the product at our discretion using new or

refurbished components.

Technical Specications

Warranty

This warranty covers defects in manufacturing that arise from the

correct use of the device. It is limited to defects in materials or

workmanship and does not cover damage caused by abuse, misuse,

unauthorised modication, power surge damage or extreme heat or

cold or corrosive environments. TreeGreen is not accountable for loss

of software, rmware, data or information resulting from the use of the

energyEGG®

The warranty also does not cover the normal wear and

tear on covers, cases, housings, connectors and accessories. The

warranty does not apply to any product with missing, altered or

defaced serial numbers.

Limits of Liability

If this product fails or does not perform as warranted,please contact

TreeGreen. TreeGreen will not be liable to you or anyone else for any

damages that result from the failure of this product. These damages

include, but are not limited to, the following: lost prots, lost savings,

lost data, damage to other equipment and incidental or consequent

damages arising from the use or inability to use this product. In no

event will TreeGreen be liable for any amount in excess of your

purchase price, not to exceed the current list price of the product.

Nothing in this warranty limits liability for death or personal injury

caused by negligence or fraud. TreeGreen specically disclaims any

other warranties, expressed or implied.

Autres manuels pour energyEGG

Table des matières

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur

TreeGreen energyEGG Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques