Trax TRH2027 Manuel utilisateur
Radio frequency: 433.05~434.79MHz
Working temperature: -10℃~50℃
-4°F~122°F
Transmitting power: 10 mW
Battery: 3V (CR2450) Battery life: >2 years
Radio range: 200 meters outdoor, 35 meters indoor
220 yards outdoor, 38 yards indoor
Technical specification
Warning
● Do not expose the remote to excessive moisture or water
● Do not strike or use excessive force on the remote
● If the remotes range is decreasing the battery may need to be replaced
● Only use CR2450 batteries in device
● If the voltage is less than 2.6V the remote will show a low voltage indicator
● Under uni-directional operating mode, pressing any button for more than
20s will stop radio signal transmission
● Under bi-directional operating mode, pressing any button for more than
5s will stop radio signal transmission
● Failure to follow these warnings may result in injury or render the remote
inoperable
● Always dispose of batteries properly
TRH2027
15-channel LCD Remote
Instructions
Button Commands
Version: T1
UP
STOP
DOWN
Channel(-)
(CH-)
Setting
button
(P2)
Channel(+)
(CH+)
TRH2027
15-Channel Remote Back
LCD
TRH2027
To remove the back cover, use a tool such as a
sim card pin, mini screwdriver or paper clip.
Press down on the center of the hole on the
backside and simultaneously slide the cover
in a downward movement.
T<10S
Locking/Unlocking Programming Function on Remotes
Hold P2 button and
install the battery
Remote
without
battery
Bi-directional mode
Uni-directional mode
Switching Between Uni-Directional and Bi-Directional Modes
Adjusting Number Of Channels
This remote can be set to have up to 15 channels. The factory default on the remote is set to all 15 channels.
The steps to adjust the number of channels are as follows:
Step 1: Briefly press < and > buttons simultaneously, the remote will display "C"
Step 2: Press < and > buttons simultaneously for at least 2 seconds, the remote will display "15"
Step 3: Using the < and > arrows select the number of channels required
Note: The factory default mode is Bi-directional
Locking of remotes is used to prevent accidental changes to the pre-set positions of the motor such as open and closed positions as
well as preferred stop positions. Once all programming is complete for the remote and motor is is recommended that the
programming function be locked to avoid unintentional changes. Please note that locking the remote only locks motor functions,
functions on the remote such as increasing channels can still be performed.
Locking Remote Programming
Press and hold the -
button for more than 15
seconds, the remote will
display "L"
The remote is now
in locked position
Within 10 seconds
press the P2 button on
the back of the remote
The remote will display
The remote is now in the
locked position. To
change motor settings
follow the unlocking steps
below
Unlocking Remote Programming
Press and hold the - button
for more than 15 seconds, the
remote will display "U"
The remote is now in
the unlocked
position
Within 10 seconds
press the P2 button on
the back of the remote
The remote will display
The remote is now in the
unlocked position and
will allow programming
changes to the motor.
Please lock the remote
programming after the
motor has been
programmed
Autres manuels Trax Télécommande
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
