Travis Industries 1250 Insert Manuel utilisateur

1250 Wood Insert

Owner's Manual

•Masonry Fireplace Insert •Zero-Clearance (Metal)

Fireplace Insert

Save these instructions

for future reference

SAFETY NOTICE:

If this appliance is not properly installed, a house fire may

result. For your safety, follow the installation directions.

Contact local building or fire officials about restrictions and

installation inspection requirements in your area.

Travis Industries, Inc.

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

www.travisproducts.com

$10.00 100-01233_000

4110304 Listed

Tested to: U.L. 1482 & ULC S628

6 Stove Installation (for qualified installers only)

Installation Options

•Masonry Fireplace Insert

•Zero-Clearance (Metal) Fireplace Insert

Features

•EPA Phase II Approved

•1.6 Cubic Foot Firebox Volume

•Single Operating Control

•Accepts Logs Up to 18" Long

•Steel Plate Construction (Up to 3/16”)

•Heavy Duty Refractory Firebrick

•Optional High-Tech Blower

Heating Specifications

Approximate Maximum Heating Capacity (in square feet)* 750 to 1,200

Maximum Burn Time Up to 8 Hours

* Heating capacity will vary depending on the home's floor plan, degree of insulation, and the outside

temperature. It is also affected by the quality and moisture level of the fuel.

Dimensions

13-1/2"

343mm

5-7/8"

150mm

20"

508mm

23-5/8"

601mm

18-5/8"

474mm

77mm

Figure 1

(a) Measure side and top clearances from the top plate. Measure front clearances from the stove face

(b) Fireplace Opening

Emissions

4.4 Grams Per Hour (EPA Phase II Approved)

8 Fireplace Insert Installation (for qualified installers only)

Fireplace Requirements

Figure 2 shows the minimum size requirements for the type of fireplace used.

Non-Combustible Hearth

Combustible Mantel

Non-Combustible Facing

Minimum

Fireplace Size Masonry

Fireplace Z.C. (Metal)

Fireplace

a Height (front) 20.75"528mm20.75"528mm

b Height (rear) 20.75"528mm20.75"528mm

c Width (front) 23.625"601mm25.625"651mm*

d Width (rear) 23.625"601mm25.625"651mm*

e Depth 13.5"343mm14.5"369mm*

f Hearth Depth

(includes insert

depth on hearth

plus required

hearth extension)

19"483mm (US)

- - - - - - - - - - - -

21"534mm

(Canada)

19"483mm (US)

- - - - - - - - - - - -

21"534mm

(Canada)

g Hearth Width 39.625"1007mm39.625"1007mm

h Facing Width 42.625"1083mm47.625"1210mm

i Facing Height 32"813mm32"813mm

j Mantel Height

35.5"902mm44"1118mm

Figure 2 * 1” (26mm) Clearance to fireplace walls is required for ZC Fireplaces.

Fireplace Altered Tag

Attach the "This fireplace has been altered..." plate to the fireplace (use two screws or other suitable

method). You may wish to place it in a location where it will be covered by the surround panels.

Fireplace Insert Installation (for qualified installers only) 9

Insert Placement Requirements

•The insert must be placed so that no combustibles are within, or can swing within (e.g. drapes,

doors), 36" (915) of the front of the insert (Figure 3 “q”).

•Insert and hearth must be installed on a level, secure floor

•The minimum clearances, facing, and hearth requirements in Figure 3 must be met. Follow the

clearances for the type of fireplace being used – (masonry or zero-clearance-metal).





Side

Wall

Combustible Mantel

Combustible Top Facing

Non-Combustible

Hearth

Facing

Minimum

Clearances Masonry

Fireplace Z.C. (Metal)

Fireplace

k Sidewall 13"331mm30"762mm

l Side Facing 9.5"242mm12"305mm

m Top Facing 12"305mm12"305mm

n Mantel 15.5"394mm24"610mm

o Front Hearth

(does not

include insert

extension “x”)

16" 407mm

(US)

- - - - - - - - - - -

18” 458mm

(Canada)

16" 407mm

(US)

- - - - - - - - - - -

18” 458mm

(Canada)

p Side Hearth 8" 204mm 8" 204mm

q Front of Insert 36"

915mm 36"

915mm

x Extension Onto

Hearth 3" 77mm 3" 77mm

Figure 3

Hearth Requirements

•Must extend 16" (USA) or 18” (Canada) in front of the insert and 8" on both sides.

•Must be non-combustible and at least .018" thick (26 gauge)

10 Fireplace Insert Installation (for qualified installers only)

Masonry Fireplace Requirements

CANADA ONLY:

The fireplace insert must be installed with a continuous chimney liner of 6” diameter extending from the

fireplace insert to the top of the chimney. The chimney liner must conform to the Class 3 requirement of

Can/ULC S635, Standard Lining Systems for Existing Masonry or Factory- Built Chimney & Vents, or

CAN/ULC S640, Standard for Lining Systems for New Masonry Chimneys.

•Chimney must have a clay tile liner or a stainless steel liner (positive connection).

•Entire fireplace, including chimney, must be clean and undamaged. Any damage must be repaired

prior to installation of the insert.

•Chimney height: 15' (4.5M) minimum; 33' (10M) maximum.

•Entire fireplace, including chimney, must meet local building requirements.

•The fireplace insert must be placed on a masonry hearth built to UBC standards.

Zero-Clearance (Metal) Fireplace Requirements

CANADA ONLY:

The fireplace insert must be installed with a continuous chimney liner of 6” diameter extending from the

fireplace insert to the top of the chimney. The chimney liner must conform to the Class 3 requirement of

Can/ULC S635, Standard Lining Systems for Existing Masonry or Factory- Built Chimney & Vents, or

CAN/ULC S640, Standard for Lining Systems for New Masonry Chimneys.

•Must utilize a positive (full reline) or direct connection (block-off plate)

•Must be manufactured by one of the following manufacturers:

• Marco • Majestic • Heatilator • Preway • Tempco • Superior

• Heat N Glo • Lennox • Martin • Monesson

•Entire fireplace, including chimney, must be clean and undamaged. Any damage must be repaired

prior to installation of the insert

•Entire fireplace, including chimney, must meet local building requirements

•Chimney height: 15' (4.5M) minimum; 33' (10M) maximum. Minimum cross section: 28.65 square

inches (18626 sq mm)

•The damper ("A") and grate ("B") must be removed (see Figure 4). The smoke shelf ("C"), internal

baffles ("D"), screen ("E"), and metal or glass doors ("F") may be removed (if applicable). The

masonry lining ("G"), insulation ("H"), and any structured rigid frame members (metal sides, floor, door

frame, face of the fireplace, etc. – "I") may not be removed or altered

Figure 4

14 Fireplace Insert Installation (for qualified installers only)

Insert with

Positive

Connection

REQUIRED IN

CANADA.









Figure 6

Insert with Direct

Connection

(Masonry

Fireplace)

NOT ALLOWED IN

CANADA.

A block-off plate or

other non-combustible

sealing device (e.g.

damper adapter) is

required. It must seal

the chimney to insure

smoke does not enter

the home while

providing the chimney

system with sufficient

draft.







Figure 7

Autres manuels pour 1250 Insert

Table des matières

Autres manuels Travis Industries Cheminée intérieure

Travis Industries

Travis Industries Flush Wood Plus Manuel utilisateur

Travis Industries

Travis Industries DVS Ember-Fyre 2.1 Log Manuel utilisateur

Travis Industries

Travis Industries 864 HO GSR2 Manuel utilisateur

Travis Industries

Travis Industries 564 HO Manuel utilisateur

Travis Industries

Travis Industries 864 ST GSR2 Manuel utilisateur

Travis Industries

Travis Industries Granite 99600200 Manuel de service

Travis Industries

Travis Industries 616 Diamond-Fyre GSR2 Manuel utilisateur

Travis Industries

Travis Industries Fire Garden 40x24 Single Sided Manuel utilisateur

Travis Industries

Travis Industries 564 Manuel utilisateur

Travis Industries

Travis Industries Xtreme 6020 Manuel utilisateur

Travis Industries

Travis Industries 4415 HO GSR2 Manuel utilisateur

Travis Industries

Travis Industries Avalon Ashpan Manuel utilisateur

Travis Industries

Travis Industries DVS GSR2 NB Insert Manuel utilisateur

Travis Industries

Travis Industries GreenSmart 2 Fireplace 564 SS GSR2 Manuel utilisateur

Travis Industries

Travis Industries DVS FIREPLACE Manuel utilisateur

Travis Industries

Travis Industries DVS FIREPLACE Manuel utilisateur

Travis Industries

Travis Industries 564 DF GSR2 Manuel utilisateur

Travis Industries

Travis Industries 430 GSR2 Manuel utilisateur

Travis Industries

Travis Industries 430 Ember-Glo GSR2 Manuel utilisateur

Travis Industries

Travis Industries Space Saver IPI Fireplace 564 Manuel utilisateur

Travis Industries

Travis Industries Xtrordinair ProBuilder 36 CleanFace MV Manuel utilisateur

Travis Industries

Travis Industries Travis DVL Manuel utilisateur

Travis Industries

Travis Industries 36 CF II Manuel utilisateur

Travis Industries

Travis Industries 616 GSR Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation