Trane WPHF Mode d’emploi

WSHP-SVX04A-EN

Models

“A” and later Design Sequence

Installation

Owner

Diagnostics

Extra High Efficiency

Water-Source Heat Pump

Models WPVJ and WPHF

WPVJ

018-072 – 60 HZ

WPHF

021-057 – 60 HZ

Notice

NOTICE:

Warnings and Cautions appear at appropriate sections throughout this manual.

Read these carefully.

WARNING -Indicates a potentially hazardous situation which, if

not avoided, could result in death or serious injury.

CAUTION -Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury. It

may also be used to alert against unsafe practices.

CAUTION -Indicates a situation that may result in equipment or

property-damage-only accidents.

NOTICE:

Unit contains HCFC (R-22) Refrigerant

Instructions!

Section 608, Paragraph C of the 1990 Clean Air Act states:

Effective July 1, 1992, it shall be unlawful for any person, in course of

maintaining, servicing, repairing, or disposing of an air conditioning system, to

knowingly vent or release any CFC or HCFC refrigerant. Minimal releases (air

purges or refrigerant hoses) associated with good faith attempts to recapture or

recycle are exempt from the ban on venting.

Responsible Refrigerant Practices!

Trane believes that responsible refrigerant practices are important to the

environment, our customers, and the air conditioning industry. All technicians

who handle refrigerants must be certified. The Federal Clean Air Act (Section 608)

sets forth the requirements for handling, reclaiming, recovering and recycling of

certain refrigerants and the equipment that is used in these service procedures.

In addition, some states or municipalities may have additional requirements that

must also be adhered to for responsible management of refrigerants. Know the

applicable laws and follow them.

Important!

Equipment is shipped FOB (Free on

Board) at the manufacturer. Therefore,

freight claims for damages against the

carrier must be initiated by the receiver.

WSHP-SVX04A-EN 3

Contents

Installation/Startup/Commissioning

Pre-installation Checklist 4

General Information 5

Dimensions/Weights 6

Installation Instructions 14

Electrical Requirements 20

Pre-Startup Checklist 25

Startup/Commissioning

Sequence of Operation 26

Operating Pressures 27

Startup Checklist & Log 30

Maintenance

Warranty Information

Troubleshooting Checklist

Unit Wiring

4WSHP-SVX04A-EN

WARNING

Fiberglass Wool!

Product contains fiberglass wool. Disturbing the insulation in this

product during installation, maintenance or repair will expose you to

airborne particles of glass wool fibers and ceramic fibers known to the

state of California to cause cancer through inhalation. Glass wool fibers

may also cause respiratory, skin or eye irritation.

Jobsite Inspection

Always perform the following checks before accepting a unit:

1. Verify that the nameplate data matches the data on the sales order and bill of

lading (including electrical data).

2. Verify that the power supply complies with the unit nameplate specifications.

3. Visually inspect the exterior of the unit, for signs of shipping damage. Do not

sign the bill of lading accepting the unit(s) until inspection has been com-

pleted. Check for damage promptly after the unit(s) are unloaded. Once the

bill of lading is signed at the jobsite, the unit(s) are now the property of the

SOLD TO party and future freight claims MAY NOT be accepted by the freight

company.

4. Verify that the refrigerant charge has been retained during shipment by use

of gauges. Schrader taps are located external to the cabinet on the 1 1/2-ton

through 6-ton equipment.

5. After assuring that charge has been retained, reinstall the schrader caps to

assure that refrigerant leakage does not occur.

WARNING

Microbial Growth!

Wet interior unit insulation can become an amplification site for

microbial growth (mold), which may cause odors and damage to the

equipment and building materials. If there is evidence of microbial

growth (mold) on the interior insulation, the insulation should be

removed and replaced prior to operating the system.

Jobsite Storage

This unit is intended for indoor use only. To protect the unit from damage due to

the elements, and to prevent possible IAQ contaminant sources from growing,

the unit should be stored indoors. If indoor storage is not possible, the following

provisions for outdoor storage must be met:

1. Place the unit(s) on a dry surface or raise above the ground to assure ade-

quate air circulation beneath the unit.

2. Cover the unit(s) with a water proof tarp to protect them from the elements.

3. Make provisions for continuous venting of the covered units to prevent

moisture from standing on the unit(s) surfaces. Wet interior unit insulation

can become an amplification site for microbial growth (mold) which has

been determined to be a cause of odors and serious health related indoor air

quality problems.

4. Store refrigeration units units in the normal UP orientation to maintain oil in

the compressor.

5. Model WPHF units should not be stacked more than three high. Do not stack

WPVJ units.

Pre-installation

Checklist

WSHP-SVX04A-EN 5

General

Information

Unit Nameplate

The unit nameplate is located at the

front of the unit. It includes the unit

model number, serial number, electri-

cal characteristics, refrigerant charge,

and other pertinent unit data.

Compressor Nameplate

The nameplate for the compressors

are located on the compressor shell.

Unit Description

Before shipment, each unit is leak test-

ed, dehydrated, charged with refriger-

ant and run tested for proper control

operation.

Water-to-Refrigerant Coils

The co-axial water-to-refrigerant heat

exchanger for the 1 1/2-ton through 6-

ton equipment is constructed of cop-

per or cupro-nickel (option) for the wa-

ter section and stainless steel for the

refrigeration section.

The heat exchanger is leak tested to

assure there is no cross leakage be-

tween the water and refrigerant gas.

Water Connections

Water connections are located at the

unit front for both the WPVJ and

WPHF units. They are clearly labled for

supply/return connection. Sizes are as

follows.

Blower/Motor

The blower and motor is located inside

the unit cabinet. The motor may be

easily removed for service through the

equipment blower access panel.

Controls

The control system offered to control

the unit is a Basic 24 volt control, Basic

24 volt control, or TracerTM ZN510

control. A 50 VA transformer is factory

supplied on the Basic 24V control con-

figurations. A 75 VA transformer is fac-

Dia. Type

3/4" WPHF 021-027 - Water in/out

1" WPHF 030-072 - Water in/out

1" WPVJ - Water in/out

3/4" Drain

1/2" Desuperheater

tory supplied on the ZN510 (digital)

control configurations.

ZN510 Controls

(WPVJ and WPHF option)

Units incorporating the ZN510 control

option design will include a digital

LonTalkTM certified control board. The

control board will support such op-

tions as: random start delay, heating/

cooling status, occupied/unoccupied

mode and fan/filter status.

Power wiring is made at the contactor.

See manual WSHP-IOP-2 for diagnos-

tic information.

Schrader Connections

Connections for the low and high side

of the refrigeration system are located

conveniently at the equipments front

panel. Sheet metal removal is not re-

quired for positive connection to the

high and low schrader connections.

6WSHP-SVX04A-EN

Table 1: Unit weights

Size

Shipping

Weight

with pallet (lb)

Shipping

Weight

w/o pallet (lb)

WPVJ

018 249 239

024 250 240

030 298 288

036 315 305

042 324 314

048 398 388

060 439 429

072 440 430

WPHF

021, 027 279 267

035. 040 367 356

047, 057 433 403

WARNING

Improper Unit Lift!

Test lift unit approximately 24 inches to verify proper

center of gravity lift point. To avoid dropping of unit,

reposition lifting point if unit is not level. Failure to

properly lift unit could result in death or serious injury

or possible equipment or property-only damage.

Dimensions/Weights/

Clearance

Figure 2: Mechanical clearances - WPVJ

Unit Location and Clearances

Locate the unit in an indoor area. The

ambient temperature surrounding the

unit must not be less than 45°F. Do not

locate the unit in areas subject to

freezing.

Attention should be given to service

clearance and technician safety. The

unit should be easily maintained or

serviced in all applications. There

must be enough space for service per-

sonnel to perform maintenance or re-

pair. Provide sufficient room to make

water, and electrical connection(s). Lo-

cal and national codes should be fol-

lowed in providing electrical power

connections. See Figure 1 and 2for

mechanical clearances.

Figure 1: Mechanical clearances - WPHF

WSHP-SVX04A-EN 7

Dimensions

WPHF 021-057

8WSHP-SVX04A-EN

Dimensions

WPVJ 018-024 LH

WSHP-SVX04A-EN 9

Dimensions

WPVJ 018-024 RH

10 WSHP-SVX04A-EN

Dimensions

WPVJ 030-042 LH

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Trane Pompe à chaleur

Trane

Trane FLEX HP HT Manuel du propriétaire

Trane

Trane Exergy RE 210 Manuel utilisateur

Trane

Trane 22-5213-WEB01 Manuel utilisateur

Trane

Trane 4TWX7 Series Instructions de montage

Trane

Trane Ultra-Low NOx Series Instructions de montage

Trane

Trane CXAU Instructions d'installation et d'utilisation

Trane

Trane A4HP4018D1000A Instructions de montage

Trane

Trane 5TTR3018-060 Manuel utilisateur

Trane

Trane 4TWR5018E Instructions de montage

Trane

Trane 4TTR4018N Manuel utilisateur

Trane

Trane Axiom EXW Series Instructions d'installation et d'utilisation

Trane

Trane Horizon OAKD Series Instructions d'installation et d'utilisation

Trane

Trane DCY060F1 Mode d’emploi

Trane

Trane 18 Series Instructions de montage

Trane

Trane WEATHERTRON 4TWX6 Instructions de montage

Trane

Trane XR15 Manuel d'utilisation

Trane

Trane 5TTX5018 Manuel utilisateur

Trane

Trane GEHB018 Manuel utilisateur

Trane

Trane ComfortLink II 4TWZ0036B1000A Manuel de service

Trane

Trane A4HP5 Manuel utilisateur

Trane

Trane 4TCC4024A1000A Instructions de montage

Trane

Trane XR13 Manuel utilisateur

Trane

Trane Axiom GEHE006 Instructions d'installation et d'utilisation

Trane

Trane 4WCY4036B3 Manuel utilisateur

Manuels Pompe à chaleur populaires d'autres marques

MICROWELL

MICROWELL HP 1000 GREEN Manuel utilisateur

Sanyo

Sanyo SAP120FCH Manuel utilisateur

Daikin

Daikin EHYHBH05AA Manuel utilisateur

Panasonic

Panasonic WH-SDF03E3E5 Mode d’emploi

Bryant

Bryant 544B Manuel utilisateur

Airxcel

Airxcel 45000 Series Manuel

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manuel utilisateur

Dimplex

Dimplex LI 16I-TUR Guide de l'utilisateur

Carrier

Carrier WSHP Open v3 Guide de configuration rapide

TGM

TGM CTV14CN018A Manuel utilisateur

Carrier

Carrier 38MGQ Series Manuel utilisateur

Kokido

Kokido K2O K880BX/EU Guide de dépannage

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guide rapide

Carrier

Carrier 48EZN Manuel utilisateur

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Mode d'emploi

Ariston

Ariston NIMBUS Manuel utilisateur

Weishaupt

Weishaupt WWP L 7 Guide de l'utilisateur

GE Zoneline AZ85H09EAC Manuel utilisateur