TrackSafe TSB 0001 Manuel utilisateur

Pet GPS Tracker TSB 0001

(GPS+GSM+SMS/GPRS)

User Manual Version 1.8

Thank you for purchasing the GPS tracker. This manual explains how to operate the

device; read it carefully before operatingthe device. Please note that the specification

and information contained in this manual are subject to change without prior notice;

any change will be integrated into the latest release. The manufacturer does not accept

liability for any errors or omissions that may be contained in this document.

I. Accessories.

Your package contains the following:

II. Technical data

Quantity Item

1 Pet GPS Tracker

1 Electrical plug

1 USB docking station (USB charger)

1 Screw driver

1 User manual

GSM Frequency 850/900/1800/1900MHZ

GSM/GPS chip MTK6260/MTK3337

GPRS Class 12,TCP/IP build in GSM MODULE

GPS sensitivity -159dBm

GPS location accuracy 5-25m

LBS location accuracy 50-200m

Speed accuracy 0.1m/Second

GPS cold start <38 second

GPS warm start <32 second

GPS hot start <2 second

Maximum Elev 18,000m

maximum speed 515m/second

Weight 50g

Average standby current <10mA

Operating temperature -20---70℃

Humidity 20%---80%

Dimensions 56mm×36mm×16 mm (main unit)

Voltage Rechargeable 500mAh battery

Power supply DC5V

Standby time >72h

III. Be prepared before start-up

1.Prepare a SIM card in tracker

a) SIM card needs to be GSM Network;

b) SIM card needs to have Caller Identification function;

c) SIM card needs to have GPRS function;

d) SIM card needs to have SMS function;

Important note: Please turn power off before installing or removing the SIM card;

2. Switch on the device:

Plug the device into the USB docking station to switch it on automatically.

3. Switch off the device: (for non-charging status only)

SMS text command: shutdown#

4. Charging Status

a) Starting charging: When the device starts to charge, the orange and blue LED will

continually blink.

b) Fully Charged: When fully charged, the orange light will blink every 2 seconds.

Quick start-up

1.Set up the administration number. This is the phone number the tracker will

accept commands from. To setup the administration number, simply send the

following SMS message to the tracker’s mobile number from your mobile

phone: SMS Template:

pw,123456,center,<the_administration_phone_number>#

Example:pw,123456,center,008618676389718#

If successful, the device will reply with: center:008618676389718. ok!

2. Set up your time zone.

SMS Template:lang,0,zone,<time_zone>#

where <time_zone> is the time difference to GMT.

For example to set up China time zone, send the following message:

lang,0,zone,+8#

When successful, the device will reply with:[ lang,0,zone,+8#] ok!

3. To check the status and all information of the device, please send below

command

test#

4.To check your GPS tracker is operating correctly, send the following SMS to the

tracker’s number:

SMS Template:

url#

The tracker will reply by SMS with a link. Simply select the link and your

phone’s map program will open to show the current location of the device.

5.If you intend to use the mobile App or the platform, then you may need to set the

APN. You probably won’t need to set this as most networks will provide a

SIM which automatically allows access.

a) Please refer to test# reply, if GPRS:OK, that means APN no need to set.

b) If GPRS:NO, that means APN need to set. Contact your network provider for

the APN name.

SMS Template:apn,apn name,user,password,#

For example, if you are using a SIM card from China Unicom, the APN is

‘3gnet’ and does not require a user name nor password. You should send the

following command:

apn,3gnet,,,#

You will get SMS reply as below as long as the format is correct.

After the APN is set, please resend command of test# to check if GPRS is OK. If

still NO, please double confirm with your network provider.

6. Low battery alarm:

When the battery level reaches less than 20%, the device will send a low power

alert SMS text to the center number (3 times).

IV. Commands summary

The following are commands that you can send to your GPS tracker using SMS.

The tracker will process the request and reply accordingly. Note that the

commands should be sent using the exact case (lower or uppercase) as in the table

below:

Description SMS template Example

Set up an

administration phone

number

pw,123456,center,<the_administrati

on_phone_number>#

pw,123456,center,008618

676389718#

Change the default

password (a) (see

below)

pw,<new_password># pw,888888#

Set up an auxiliary

administration phone

number

pw,123456,slave,<the_administrati

on_phone_number>#

pw,123456,slave,

008618676389718#

Set up the time lang,<language_id>,zone,<time_zo

ne>#

lang,0,zone,-0#

Check the tracker’s

settings

test# test#

Request the tracker’s

current position

url# url#

Set up the tracker for

use with Mobile App

and the internet

apn,<mobile_network_apn>,<apn_

user_name>,<apn_password>#

apn,data.xyz.com#

Change the tracker’s

operation mode (b)

m<mode_number>,<upload_interv

al_in_seconds>#

m2,600#

Change the data upload

time interval (b)

upload,<upload_interval_in_second

s>#

upload,300#

Restart the tracker reset# reset#

Restore factory settings factory# factory#

Set a different platform

server

ip,<ip_address>,port,<port_number

ip,59.188.20.67,port,7018

a) The default password is 123456. The new password has to be 6 digits long.

b) There are four modes of operation, so <mode_number> varies from [1-4]

depending on the mode you wish to select. The <upload_time_interval> is

expressed in seconds and varies from [10-65535] seconds.

Mode 1 – (Command: m1,10#) – Default Working Mode. GSM and GPS are

active, the device will send GPS data to the server every 10s (10#). (10s to 65535s,

default 10s).

Mode 2 – (Command: m2,600#) – Power saving mode. Device sleeps, but turns on

GPS and sends the data to the server at set intervals (Minimum 600s).

Mode 3 – (Command: m3,20#) – LBS (Location Based Service) mode. GPS is

switched off; the device uses its closest mobile network tower to determine a (less

accurate) location.

Mode 4 – (Command: m4#) – Sleep Mode. Always sleeps unless woken up by

calling or SMS text. It can send a Google Maps link by SMS.

V. Using the mobile App

The Android app can be downloaded by scanning the QR code below:

For iOS, use this QR code:

VI. Using the platform

Platform website: http://www.track188.com/

Use the ‘test#’ command to find out your device ID. Unless you have changed it, the

default password is ‘123456’.

Table des matières

Autres manuels TrackSafe GPS

TrackSafe

TrackSafe Buddy Manuel utilisateur

Manuels GPS populaires d'autres marques

Raven

Raven Cruizer II Manuel

Hama

Hama 53118 Manuel utilisateur

Garmin

Garmin SOUNDER 125 Manuel utilisateur

Garmin

Garmin DEZL 580 Manuel utilisateur

Jigabot

Jigabot EX Manuel utilisateur

Pointer

Pointer Cellocator CelloTrack XT LTE Guide d'installation

Queclink

Queclink GV55LITE Manuel utilisateur

Voxson

Voxson Voxtrack GPS500 Manuel d'instructions

Garmin

Garmin ECHOMAP PLUS Manuel utilisateur

Starcom Systems

Starcom Systems Kylos Compact Manuel utilisateur

Garmin

Garmin 15 H Series Manuel utilisateur

Cobra

Cobra Marine MC 600Ci Manuel utilisateur

Cellocator

Cellocator CelloTrack T Manuel utilisateur

Enfora

Enfora Mini-MT GSM2228UG001 Manuel utilisateur

Magellan

Magellan eXplorist 100 Manuel utilisateur

LTE

LTE G50B Manuel utilisateur

Garmin

Garmin DEZL OTR500 Manuel utilisateur

SkyGolf

SkyGolf SkyCaddie SG1 Manuel utilisateur