TPG CA-203A Manuel utilisateur

向量變頻器

Vector control inverter

Operating manual

CA Series

www.tpg-tw.com

Contents

Chapter 1 Inspection and safety orecautions........................................1

1‐1.Inspectionafterunpacking ............................................. 1

1-1-1. Instructions on nameplate............................................ 1

1-1-2. Model designation......................................................... 1

1‐2.Safetyprecautions .......................................................... 2

1‐3.Precautions...................................................................... 4

1‐4.Scopeofapplications ...................................................... 7

Chapter 2 Standard specifications.........................................................8

2‐1.Technicalspecifications................................................... 8

2‐2.Technicalspecifications................................................... 9

Chapter 3 Keyboard .............................................................................13

3‐1.Keyboarddescription .................................................... 13

3‐2.Keyboardindicators ...................................................... 13

3‐3.Descriptionofoperationpanelkeys............................. 14

3‐4.Examplesofparametersettings ................................... 14

3-4-1. Password settings........................................................ 16

3-4-2. Motor parameter auto tunning.................................. 16

Chapter 4 Installation and commissioning .........................................18

4‐1.Operatingenvironment ................................................ 18

4‐2.Installationdirectionandspace ................................... 18

4‐3.Wiringdiagram ............................................................. 18

4‐4.Maincircuitterminal..................................................... 20

4-4-1. CASERIES main circuit terminal ............................ 20

4-4-2. Function Description of Terminals............................ 20

4‐5.Controlcircuitterminals ............................................... 20

4-5-1. Description of control circuit terminals.................... 20

4-5-2.Arrangement of control circuit terminals................. 21

4‐6.Wiringprecautions: ...................................................... 21

4‐7.Sparecircuit................................................................... 22

4‐8.Commissioning .............................................................. 23

Chapter 5 Function parameter............................................................24

5‐1.Menugrouping.............................................................. 24

5-1-1. d0 Group - Monitoring function................................ 25

5-1-2. F0 Group - Basic function.......................................... 26

5-1-3. F1 Group - Input terminals ....................................... 27

5-1-4. F2 Group - Output terminals..................................... 29

5-1-5. F3 Group - Start and stop control............................. 31

5-1-6. F4 Group - V/F control............................................... 31

5-1-7. F5 Group - Vector control group............................... 32

5-1-8. F6 Group - Keyboard and display............................. 32

5-1-9. F7 Group -Auxiliary function................................... 33

5-1-10. F8 Group - Fault and protection............................. 34

5-1-11. F9 Group - Communication parameter.................. 35

5-1-12. FA Group - Torque control....................................... 36

5-1-13. Fb Group - Control optimization............................ 37

5-1-14. E0 Group - Wobbulate control ................................ 38

5-1-15. E1 Group - Multi-speed control............................... 38

5-1-16. E2 Group - PID control............................................ 38

5-1-17. E3 Group - Virtual DI, Virtual DO......................... 39

5-1-18. b0 Group - Motor parameters................................. 41

5-1-19. y0 Group - Function code management.................. 42

5-1-20. y1 Group - Fault history search............................... 42

5‐2.Functionparameterdescription................................... 42

5-2-1. dO Group - Monitoring function group.................... 42

5-2-2. F0 Group - Basic function group............................... 44

5-2-3. F1 Gruop - Input terminals group ............................ 49

5-2-4. F2 Group - Output terminals group.......................... 54

5-2-5. F3 Group - Start and stop control group.................. 58

5-2-6. F4 Group - V/F control group.................................... 59

5-2-7. F5 Group - Vector control group............................... 61

5-2-8. F6 Group - Keyboard and display group ................. 62

5-2-9. F7 Group -Auxiliary function group........................ 64

5-2-10. F8 Group - Fault and protection group.................. 67

5-2-11. F9 Group - Communication parameter group....... 70

5-2-12. FA Group - Torque control group ........................... 72

5-2-13. Fb Group - Control optimization group................. 73

5-2-14. E0 Group - Wobbulate control group..................... 74

5-2-15. E1 Group - Multi-speed control group ................... 75

5-2-16. E2 Group - PID control group................................. 77

5-2-17. E3 Group - Virtual DI, virtual DO group............... 80

5-2-18. b0 Group - Motor parameter group........................ 83

5-2-19. y0 Group - Function code management.................. 84

5-2-20. y1 Group - Fault history search group.................... 85

Chapter 6 Fault message and troubleshooting....................................87

6‐1.Faultmessageandtroubleshooting ............................. 87

6‐2.Definition....................................................................... 89

6‐3.EMCstandard ................................................................ 89

6‐4.EMCdirective ................................................................ 90

6-3-1. Harmonic effect........................................................... 90

6-3-2. Electromagnetic Interference and Installation

Precautions............................................................................................. 90

6-3-3. Remedies for the interferences from the surrounding

electromagnetic equipments to the inverter:....................................... 90

6-3-4. Remedies for the interferences from the inverter to

the surrounding electromagnetic equipments: ................................... 91

6-3-5. Remedies for leakage current .................................... 91

6-3-6. Precautions on Installing EMC input filter at the

input end of power supply .................................................................... 92

Chapter 7 Dimensions...........................................................................93

7‐1．Dimensions.................................................................. 93

7-1-1.Appearance and installation holes size...................... 93

7-1-2. CA SERIES.................................................................. 93

7-1-3. Keyboard size diagram............................................... 94

Chapter 8 Maintenance and repair.....................................................95

8‐1.Inspectionandmaintenance ........................................ 95

8‐2.Partsforregularreplacement....................................... 96

8‐3.Storage........................................................................... 96

8‐4.Capacitor ....................................................................... 96

8-4-1.Capacitor rebuilt.......................................................... 96

8‐5.Measuringandreadings................................................ 97

Chapter 9 Warranty..............................................................................98

Appendix I RS485 communication protocol...............................- 99 -

I‐1.Introduction ............................................................... ‐99‐

I‐2.Details......................................................................... ‐99‐

Chapter 1 Inspection and safety orecautions

TPG frequency inverters have been tested and inspected before leaving factory.

After purchasing, please check if its package is damaged due to careless transportation,

and if the specifications and model of the product are consistent with your order

requirements. For any problem, please contact your local authorized TPG dealer or

directly contact this company.

1-1.Inspection after unpacking

※ Check if that packing container contains this unit, one manual and one warranty

card.

※ Check the nameplate on the side of the frequency inverter to ensure that the

product you have received is the right one you ordered.

1-1-1.Instructions on nameplate

1-1-2.Model designation

Chapter 1 Inspection and safety precautions

1-2.Safety precautions

Safety precautions in this manual are divided into the following two categories:

Danger: the dangers caused by failure to perform required operation, may result in

serious body injury or even death;

Caution:the dangers caused by failure to perform required operation,may

result in moderate injury or minor injury, and equipment damage;

Process Type Explanation

Before

installation Danger

★When unpacking, if control system with water, parts

missed or component damaged are found, do not install!

★If packing list does not match the real name, do not

install!

★Gently carry with care,otherwise there is the risk of

damage to equipment!

★Please do not use the damaged driver or the frequency

inverter with missed pieces,otherwise there is the risk of

injury!

★Do not use your hand to touch the control system

components, otherwise there is the risk of electrostatic

damage!

Danger

★Please install the unit on the metal or flame retardant

objects; away from combustible material. Failure to do so

may cause a fire!

★Never twist the mounting bolts of the equipment

components, especially the bolt with the red mark!

When

installing

Note

★Do not let the lead wires or screws fall into the driver.

Otherwise which may cause damage to the driver!

★Keep the driver installed in the place where less

vibration, avoid direct sunlight.

★When two or more converters are installed in a cabinet,

please pay attention to the installation location, ensure the

good heat dissipation effect.

When wiring

Danger

★Must comply with this manual's guidance,any

construction shall be performed by a professional

electrician, otherwise there would be the unexpected risk !

★A circuit breaker must be set between the inverter and

the power supply to separate them, otherwise it may cause a

fire!

★Verify if power is a zero-energy status before wiring,

otherwise there is a risk of electric shock!

★The inverter shall be grounded correctly according to

standard specifications, otherwise there is a danger of

electrical shock!

★Never connect the input power to the inverter output

terminals (U, V, W) . Note that the mark of the terminals,

Chapter 1 Inspection and safety precautions

Process Type Explanation

do not incorrectly connect wires! Otherwise which may

cause damage to the driver!

★Ensure that the distribution line meets the regional safety

standards of EMC requirements. The diameter of used

wire shall refer to the recommendations of this manual.

Otherwise it may cause an accident!

★When connecting to braking resistor,the braking resistor

must be connected to position between terminals (P, RB) of

the inverter

Note

★Please confirm whether the input power voltage is same

as the inverter rated voltage; wiring positions of power

input terminals (R,S,T) and output terminals (U,V,W) are

correct or not; and note that if there is a short circuit in the

peripheral circuit connected to driver,if the connected

lines are tight, otherwise it may cause damage to the

driver!

★Do not need to perform withstand voltage test for any

part of the inverter,this product has been tested before

leaving factory. Otherwise it may cause an accident!

Before

energizing

Danger

★The inverter's cover plate must close before power on.

Otherwise it may cause an electric shock!

★Wiring of all external accessories must comply with the

guidance of this manual,please correctly wiring in

accordance with the circuit connection methods described

in this manual. Otherwise it may cause an accident!

After

energizing Danger

★Do not open cover plate after energizing. Otherwise

there is a risk of electric shock!

★Do not touch the driver and peripheral circuits with wet

hands. Otherwise there is a risk of electric shock!

★Do not touch any input and output terminals of the

inverter. Otherwise there is a risk of electric shock!

★The inverter automatically perform the safety testing for

the external strong electrical circuit in the early stages of

energizing, therefore never touch the driver terminals (U,

V, W) or motor terminals, otherwise there is a risk of

electric shock!

★If you need to identify the parameters, please pay

attention to the danger of injury during motor rotation.

Otherwise it may cause an accident!

★Please do not change the inverter manufacturer

parameters. Otherwise it may cause damage to this unit!

During

operation Danger

★Do not touch the cooling fan and the discharge resistor

to feel the temperature. Otherwise it may cause burns!

★Non-professional personnel is not allowed to detect

signal when operating. Doing so may cause personal

injury or damage to this unit!

Chapter 1 Inspection and safety precautions

Process Type Explanation

Note

★When the inverter is operating, you should avoid that

objects fall into this unit.Otherwise cause damage to this unit!

★Do not start/stop the driver by switching on/off

contactor. Otherwise cause damage to this unit!

When

maintaining Danger

★Do not perform repairs and maintenance for the live

electrical equipment. Otherwise there is a risk of electric

shock!

★The repairs and maintenance task can be performed only

when the inverter voltage is lower than AC36V,generally

that is two minutes after powering off. Otherwise, the

residual charge from capacitor would cause personal

injury!

★Non-well-trained professional personnel is not allowed

to perform repairs and maintenance of inverter. Doing so

may cause personal injury or damage to this unit!

★After replacing the inverter,parameter settings must be

redone, all pluggable plugs can be operated only in the

case of powering off!

1-3.Precautions

No. Type Explanation

1 Motor insulation

inspection

Please perform motor insulation inspection for the first

time use, re-use after leaving unused for a long time as

well as regular check, in order to prevent damage to the

inverter because of the motor's winding insulation failure.

Wiring between motor and inverter shall be disconnected,

it is recommended that the 500V voltage type megger

should be adopted and insulation resistance shall be not

less than 5MΩ.

2 Motor thermal

protection

If the rated capacity of the selected motor does not match

the inverter, especially when the inverter rated power is

greater than the motor rated power,be sure to adjust the

motor protection parameter values inside inverter or install

thermal relay in the front of motor for motor protection.

3 Run over power

frequency

This inverter can provide (0Hz to 400Hz）output

frequency If the user is required to run at 50Hz or more,

please consider the endurance of your mechanical devices.

4 Vibrations of

mechanical device

Inverter output frequency may be encountered mechanical

resonance point of the load device, you can set jump

frequency parameter inside inverter to avoid the case.

5 Motor heat and

noise

The inverter output voltage is PWM wave that contains a

certain amount of harmonics, so the temperature rise,noise

and vibration of motor show a slight higher than frequency

power frequency operation.

Chapter 1 Inspection and safety precautions

No. Type Explanation

Output side with

piezoresistor or

capacitor for

improving power

factor

The inverter output is PWM wave, if the piezoresistor for

lightning protection or the capacitor for improving power

factor is installed in the output side, which easily cause the

inverter instantaneous overcurrent or even cause damage

to the inverter. Please do not use.

Contactor or

switch used in the

inverter

input/output

terminals

If contactor is installed between power supply and

inverter,the contactor is not allowed to start/stop the

inverter. Necessarily need to use the contactor to control

the inverter start/stop, the interval should not be less than

one hour. Frequent charging and discharging may reduce

the service life of the inverter capacitor. If the contactor or

switch is equipped between output terminals and motor,

the inverter should be turned on/off without output status,

otherwise which easily lead to damage to the inverter

module.

8 Use other than the

rated voltage

CA Series inverter is not suitable for use beyond the

allowable operating voltage described in this

manual,which easily cause damage to the parts inside

inverter. If necessary, please use the corresponding

transformer to change voltage.

Never change 3-

phase input to 2-

phase input

Never change CA Series 3-phase inverter to 2-phase one

for application. Otherwise it will lead to malfunction or

damage to the inverter.

10 Lightning surge

protection

The series inverter is equipped with lightning overcurrent

protection device, so it has the ability of self-protection to

lightning induction. For the area where lightning is

frequent, user should also install the extra protection in the

front of the inverter.

High altitude and

derating

application

When the inverter is used in areas over 1000m altitude,it is

required to reduce frequency because the thin air will

decrease the cooling effect of inverter. Please consult our

technician for details on the application.

12 Special use

If the user need to use methods other than the suggested

wiring diagram provided in this manual, such as common

DC bus, please consult our technician.

Precautions for

scrap disposal of

the inverter

It may explode when electrolytic capacitors on the main

circuit and printed circuit board are burned. When burning

plastic parts, it may produce toxic gases.Please disposing as

industrial waste.

14 About

adaptive motor

1) Standard adaptive motor shall be four-pole

asynchronous squirrel-cage induction motor. Apart

from the said motors, please select the inverter

according to the motor rated current.

2) The cooling fan and the rotor shaft for non-inverter

motor are coaxially connected, the fan cooling effect is

reduced when the rotational speed is reduced, therefore,

Chapter 1 Inspection and safety precautions

No. Type Explanation

when the motor works in overheating occasions,a strong

exhaust fan should be retrofitted or replace non-inverter

motor with the inverter motor;

3) The inverter has built-in the adaptive motor standard

parameters, according to the actual situation, please

identify motor parameters or accordingly modify the

default values to try to meet the actual value,otherwise it

will operation affect and protection performance;

4) When short-circuit of cable or motor internal will

activate the inverter alarm, even bombing. Therefore,

firstly perform insulation short-circuit test for the initial

installation of the motor and cable, routine maintenance

often also need to perform such test. Note that the parts

to be tested and the inverter shall be disconnected

completely when testing.

15 Others

1) Never connect the AC power to the inverter output

terminals (U, V, W) .

2) Properly fix and lock the panel before powering on, so

as to avoid hurting the personal safety due to internal

poor capacitors.

3) Never perform wiring, checking and other operations

after power is turned on.

4) Do not touch the internal circuit board and its

components in order to avoid the risk of electric shock

after this unit is powered,

5) Do not touch internal circuit board and any parts after

powering off and within five minutes after keyboard

indicator lamp goes out,you must use the instrument to

confirm that internal capacitor has been discharged

fully,otherwise there is a danger of electric shock.

6) Body static electricity will seriously damage the internal

MOS field-effect transistors, etc.,if there are not anti-

static measures, do not touch the printed circuit board

and IGBT internal device with hand, otherwise it may

cause a malfunction.

7) The ground terminal of the inverter (E or ）shall be

earthed firmly according to the provisions of the

National Electrical Safety and other relevant standards.

Do not shut down (power off) by pulling switch,and

only cut off the power until the motor stopping

operation.

8) It is required to add the optional input filter attachment

so as to meet CE standards

Chapter 1 Inspection and safety precautions

1-4.Scope of applications

※ This inverter only applies to typical industrial three-phase AC asynchronous motor.

※ This inverter can only be used in those occasions recognized by this company, an

unapproved use may result in fire, electric shock, explosion and other accidents.

※ If the inverter is used in such equipments (e.g: equipments for lifting

persons,aviation systems, safety equipment, etc.) and its malfunction may result in

personal injury or even death. In this case,please consult the manufacturer for your

application.

Only the well-trained personnel can be allowed to operate this unit,

please carefully read the instructions on safety, installation, operation and

maintenance before use. The safe operation of this unit depends on proper

transport, installation, operation and maintenance!

Chapter 2 Standard specifications

2-1.Technical specifications

Inverter model Rated output

Power KW)

Rated input

Current(A)

Rated output

current (A)

Adaptive motor

Power (KW)

Single phase 220V ±10%

CA-203A 0.4 5.4 2.5 0.4

CA-204A 0.75 8.2 4.0 0.75

CA-207A 1.5 14.0 7.0 1.5

CA-210A 2.2 23 10 2.2

Three-phase 220V ±10%

CA-203S 0.4 4.1 2.5 0.4

CA-204S 0.75 5.3 4.0 0.75

CA-207S 1.5 8.0 7.0 1.5

Three-phase 380V ±10%

CA-401S 0.4 2.0 1.2 0.4

CA-403S 0.75 4.3 2.5 0.75

CA-404S 1.5 5.0 3.8 1.5

CA-405S 2.2 5.8 5.1 2.2

CA-409S 3.7 10 8.5 3.7

Note: the 220V voltage level can be used as a brake unit selection; 380V voltage

brake unit as the standard, can not do for selection.

Chapter 2 Standard specifications

2-2.Technical specifications

Items Specifications

Voltage and frequency

levels

Single phase 220V, 50/60Hz

Three-phase 220V, 50/60Hz

Three-phase 380V,50/60Hz

Power

Allowable fluctuation

Voltage: ± 10% ;Frequency: ± 5%

The voltage unbalance rate is less than 3% and the

distortion rate meets the IEC61800-2 standard.

Control system High performance vector control inverter based on

DSP

Output frequency 0.00 to 400.0Hz

Control method V/F control

Open-loop flux vector control

Automatic torque

boost function

Realize low frequency (1Hz) and large output

torque control under the V/F control mode.

Frequency setting

resolution

Digital: 0.01Hz

Analog: highest frequency × 0.2%

V/F curve mode Linear,square root/m-th power,custom V/F curve

Over load capability Rated Current 150% - 60 seconds, Rated Current

200% - 1 seconds

Slip compensation Slip compensation available

Carrier Frequency 1kHz to 15kHz

Start torque 0.5Hz/150% (Open-loop flux vector control)

Speed range 1:100 (Open-loop flux vector control)

Steady-speed precision

(Speed control accuracy)

Open-loop flux vector control: ≤± 0.5% (rated

synchronous speed)

Torque response ≤40ms (Open-loop flux vector control)

Torque boost Automatic torque boost; manual torque boost (0.1%

to 30.0%)

Linear ac/deceleration

Linear acceleration and deceleration mode; two

kinds of acceleration and deceleration time; time

range 0.1s to 3600.0s.

DC braking

DC braking frequency: 0.00Hz to max.output

frequency;

Braking time: 0.0 to 50.0 seconds

Braking current value: 0.0% to 150.0%

Jogging control

Jog Frequency Range: 0.00Hz to max.output

frequency;

Jog Ac/deceleration time: 0.1s to 3600.0s

Multi-speed operation Achieve up to 16-speed operation through the

control terminal

Control system

Built-in PID Easy to realize closed-loop control system for the

process control.

Chapter 2 Standard specifications

Items Specifications

Automatic voltage

regulation (AVR)

Automatically maintain a constant output voltage

when the voltage of electricity grid changes

Running method Keyboard/terminal/communication

Frequency

setting

Total 8 frequency stetting modes: digital,analog

voltage/current, multi-speed and serial port.

Start signal Forward run

Reverse run

Multi-speed At most 16-speed can be set (run by using the

multi-function terminals )

Multi-stage

acceleration

At most 2-stage acceleration can be set (run by

using the multi-function terminals)

Emergency stop Interrupt controller output

Wobbulate run Process control run

Jog running Slow speed running

Fault reset When the protection function is active, you can

automatically or manually reset the fault condition.

Input signal

PID feedback

signal Including DC 0 to 10V/0 to 20mA

Running status Motor status display, forward, reverse, program

running status.

Fault output Relay contact capacity AC 250V/7A

Analog output

1-way analog output, 9 signals can be selected such

as frequency,current,voltage and other, output

signal range (DC 0 to 10V/0 to 20mA) .

Output signal

Output signal 2-way output,there are 8 signals each way

Run function

Limit frequency,jump frequency,slip

compensation,reversal protection, auto-tuning, PID

control

DC current braking

Built-in PID regulates braking current to ensure

sufficient braking torque under no overcurrent

condition.

Running command

channel

Three channels: operation panel,control terminals

and serial communication port. They can be

switched through a variety of ways.

Frequency source

Total 8 frequency sources: digital,analog

voltage,analog current, multi-speed and serial port.

They can be switched through a variety of ways.

Input terminals 5 digital input terminals, compatible with the active

PNP or NPN input. 2 Analog input terminals

Running

Output terminals

One digital output terminals (bipolar output) ; one

relay output terminal; 2 analog output terminals

respectively for optional range (0 to 20mA or 0 to

10V),they can be used to set frequency, output

Chapter 2 Standard specifications

Items Specifications

frequency, speed and other physical parameters.

Support 0.1-10kHz square signal output.

Inverter protection

Overvoltage protection, undervoltage protection,

overcurrent protection, overload protection,

overheat protection, overcurrent stall protection,

overvoltage stall protection, external fault,

communication error, PID feedback signal

abnormalities.

IGBT temperature

display Displays current temperature IGBT

Instantaneous power-

down restart

Less than 15 milliseconds: continuous operation.

More than 15 milliseconds: automatic detection of

motor speed, instantaneous power-down restart.

Speed start tracking

method

The inverter automatically tracks motor speed after

it starts

Protection function

Parameter protection

function

Protect inverter parameters by setting administrator

password and decoding

Running

message

Monitoring objects including: running frequency,

set frequency, output current, DC bus voltage,

output voltage, actual motor speed, PID setting

value, PID feedback value, input terminal status,

output terminal status, analog AI1 value, analog

AI2 value,current stage of multi-speed, torque set

value, etc.

LED

Keyboard

Error

message

At most save 3 error messages,and the

time,type,voltage,current,frequency and terminal

status can be queried when the failure is occurred.

LED display Display parameters

Display

Key lock It can lock all keys in order to prevent misuse.

Communica

-tion

RS485 Completely isolated RS485 communication module

can communicate with the host computer.

Environment

temperature

-10 ℃to 40 ℃(temperature at 40 ℃to 50 ℃,

please derating for use)

Storage temperature -20 ℃to 65 ℃

Environment humidity Less than 90% RH, non-condensing water droplets

Height and vibration Below 1000m, below 5.9m/s² (= 0.6g)

Environment

Application sites

Indoor where no sunlight or corrosive, explosive

gas and water vapor, dust, flammable gas, oil mist,

water vapor, drip or salt, etc.

Chapter 2 Standard specifications

Items Specifications

Altitude Below 1000m

Pollution degree 2

Product adopts safety

standards. IEC61800-5-1:2007

Product

Standard

Product adopts EMC

standards. IEC61800-3:2005

Cooling method Forced air cooling

Chapter 3 Keyboard

3-1.Keyboard description

Keyboard is used to operate CA SERIES frequency inverters, read status data and

adjust parameters.

Keyboard Schematic Diagram

3-2.Keyboard indicators

Indicator flag Name Meaning

FWD Forward running lamp ON means that the inverter is forward operating.

REV Reverse running lamp ON means that the inverter is reverse operating.

Hz Frequency Indicator Frequency unit of the inverter

Status Indicator

A Current Indicator Current unit of the inverter

Correspondence that LED displays symbols and characters/digits is as follows:

Display

letters

Corresponding

letters

Display

letters

Corresponding

letters

Display

letters

Corresponding

letters

0 1 2

3 4 5

6 7 8

9 A B

Digital

display

area

C d E

Chapter 3 Keyboard

F H I

L N n

o P r

S t U

T . -

3-3.Description of operation panel keys

Sign Name Function

Parameter

Setting/Exit Key

* Enter top menu parameter change status

* Exit from function option change

* Return to status display menu from sub-menu or

function option menu

Shift Key

* Select circularly parameters under run or stop

interface; select parameters when modifying the

parameters.

Ascending Key * Data or function code ascending

Decending Key * Data or function code decending

Run Key Used for running operation in the keyboard mode.

Stop/Reset Key

* Press the key to stop running in running status;

press the key to reset in fault alarm status, can be

used to reset the operation, the key is subject to

function code F6.00.

Enter Key * Enter into levels of menu screen,confirm

settings.

Keyboard

potentiometer

* F0.02 is set to 3,keyboard potentiometer is used

to set the running frequency.

Simultaneously press two keys to lock or unlock

the keypad.

3-4.Examples of parameter settings

Instructions on viewing and modifying function code

CA SERIES inverter operation panel has three levels of menu structure for

parameter settings and other operations. Three levels of menu is as follows: function

parameter group (first level menu) →function code (second level menu) →function

code settings (third level menu) . The operation flow is shown in the figure.

Chapter 3 Keyboard

Description: return to the second-level menu from the third-level menu by pressing

PRG key or ENTER key. The difference between the two keys : press ENTER to return

the second-level menu and save parameters setting before returning, and automatically

transfer to the next function code; press PRG to return directly to the second-level menu,

do not save parameters setting,and return to current function code .

Example 1 :restore factory default

G▲ENTER ENTER Flicker

▲

ENTER

Example 2 :change function code F0.01 from 50.00Hz to 40.00Hz

Ce manuel convient aux modèles suivants

Table des matières

Manuels Onduleur populaires d'autres marques

Fourgroup

Fourgroup Easy Manuel utilisateur

Velleman

Velleman PI300M Manuel utilisateur

Sungrow

Sungrow SG350HX-US Manuel utilisateur

WilTec

WilTec 61897 Manuel utilisateur

SMA

SMA SUNNY BOY STORAGE 2.5 Manuel utilisateur

Simplicity

Simplicity LANDLORD 316 Manuel utilisateur

Santak

Santak SMAX 3000 Manuel utilisateur

ATON

ATON RA.Store-3 Manuel utilisateur

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manuel utilisateur

Tektronix

Tektronix CFG250 Manuel utilisateur

Champion

Champion 200989 Manuel utilisateur

Vanner

Vanner 20-500 Series Manuel utilisateur

GE GEP Manuel utilisateur

Astrel Group

Astrel Group Power Reducer Guide rapide

MULTIQUIP

MULTIQUIP GDP-5H Mode d’emploi

GoWISE

GoWISE PS1007 Manuel utilisateur

Promate

Promate PM13500D ES Manuel utilisateur

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manuel utilisateur