Toyomi SJ 9000 Manuel utilisateur

COLD PRESS MASTICATING

SLOW JUICER

Model: SJ 9000

220–240V~ 50/60Hz•200W

Capacity: 500ml

Instruction Manual

IMPORTANT:

1. The Unit is designed for household use only.

2. Commercial users will not obtain the regular warranty as stated in the terms of the warranty card.

3. This is not a toy. Please do not let children play with it or use it.

IMPORTANT SAFEGUARDS

1. Make sure the electricity supply is suitable for this unit.

2. This unit is intended for household use only. Do not use the unit at outdoors or for other

purpose than intended.

3. Use the unit only as described in this manual.

4. To prevent electrical shock, do not immerse the unit, cord set and plug into water.

5. This is not a toy and not to be used by children. Close supervision is required when the unit is

used near children.

6. Ensure to unplug the unit when not in use, assembling or disassembling, and before cleaning.

7. The continuous operation time of this product should be within 20 minutes.

8. No-load or overloaded operation of machine is prohibited.

9. Do not touch or move any moving parts during operation of machine.

10. Do not use nger, spoon or chopsticks to push fruits or vegetables into the chute

of machine. Please only use the provided push rod.

11. Do not open the unit when it is operating.

12. Do not place the unit near any explosives, heated oven or hot surfaces.

13. Operate the unit only on at surfaces.

14. Do not let the cords hang over the edge of table or any other surfaces.

15. Please hold the plug to disconnect from the power socket, not by the wire.

16. If parts of product structure is found to be damaged (especially the safety device and

power cord), please stop using and send it to service centre to be repaired by

our qualied technician.

17. This product is not intended to be operated by persons (including children) with weak

physical condition, slow reaction, intellectual disability, and lack of experience, unless

they are under supervision or instruction by the person who is responsible for their safety.

NOTE:

To avoid hazard of electric shock, unplug the unit from power oulet when not in use or before

cleaning. If the supply cord is damaged, stop using immediately and bring it back to service centre

for repair.

PARTS DIAGRAM

567

Feeding Chute

Screw Shaft

Juicing Bowl

Power Base

Juice Container

Pulp Container

Push Rod

Cleaning Brush

USING FOR THE FIRST TIME

ASSEMBLING METHOD

1. Remove all packaging materials, plastic bags and labels.

2. Make sure the electricity supply is 220-240V~ 50/60Hz.

3. Clean the Containers / Feeding Chute / Screw Shaft / Juicing Bowl / Push Rod with

Soapy water. Then rinse and dry thoroughly.

NOTE : DO NOT IMMERSE THE POWER BASE UNIT IN WATER.

4. Assemble the parts per the instruction in the assembling method section.

5. Connect the power cord to the power source.

The unit is ready to use now.

Please make sure the unit is not plugged and the switch is turned to “O” setting prior to

assembling the machine.

1. Position the Juicing bowl on the Power base by aligning the position of the spouts to

the power base openings. (Fig 1)

2. Push the screw shaft rmly into the center of the bowl, making sure that it touches

down the bottom, or else the cover cannot be closed. (Fig 2)

3. Position the chute on the bowl to align the ▲ to the “ ” and twist it clockwise until it

clicks the safety lock. Please make sure that the arrow ▲ on the

cover aligns with the Lock graphic “ ” on the Bowl. (Fig 3)

4. Place the juice container and the pulp container under the relevant spouts. (Fig 4)

Fig 1 Fig 2 Fig 3 Fig 4

OPERATION INSTRUCTION

NOTE:

Please do not use the juicer longer than 20 minutes continuously.

1. Connect the unit with Power.

2. Check and make sure all parts are well assembled in correct position.

3. Make sure the machine is at o “O” position.

4. Make sure the juice and pulp containers are in position.

5. Make sure the juice spout cover is closed.

6. Prepare the fruits or vegetables and cut them into pieces max 3cm x 7cm strips or

7cm x 7cm cubes.

7. Put fruit strips/cubes into the chute.

8. Press the switch to Setting “– ” to start the juicing operation.

9. Push the food down with the pusher only.

10. In case of food stuck inside the Bowl, please switch to “R” reverse function instantly.

During the juicing process, you could keep the Leak-Proof Plug closed before the juice is full

in the juicing bowl. (Fig 5)

BENEFITS OF DRIP-STOP COVER :

1. To stop dripping at the end of juicing.

2. To mix the juice with dierent fruits and veggies.

USAGE TIPS :

1. Remove hard pits or seeds prior to pressing to prevent possible damage to the

squeezing screw.

2. If mixed juices are to be made, please begin with harder fruit, and followed by the

softer fruits.

3. Please let the juicer to run for 30 seconds after the last ingredient was fed.

ATTENTION :

The juicer is not suitable for juicing overly hard or brous and starchy fruits or vegetables

such as Sugar Cane. There are some fruits which contain too much starch to juice. Some

examples are Avocado, Bananas, gs, Mango, Papaya, Dragon Fruit, Strawberry, Grape

without seeds etc. They will clog up the stainless steel sieve.

Open & Close Of Juice Spout Cover

Fig 5

Juicer spout

is opened

Juicer spout

is closed

IMPORTANT:

Please wash the juicing parts every time immediately after each used, otherwise the pulp might

stick tightly in Juicing Bowl & Screw Shaft which will then aect the disassembly, cleaning and

juicing performance.

DISASSEMBLING METHOD

CLEANING & MAINTENANCE

NOTE:

If the juicer gets overheated, it will turn o automatically to protect the machine. In this case, please

turn the juicer o “O”. Wait 10 minutes to let the juicer cool down and then turn it on again.

To disassemble the unit after use and before cleaning. Please turn the juicer to “O” position

and disconnect the juicer from power source.

Then, please follow the steps below:

1. Remove the Juice and Pulp containers. (Fig 6)

2. Remove the Chute. Turn the chute anti-clockwise until the ▲ aligns with the “ ”

sign. (Fig 7)

3. Remove the Screw Shaft by pulling it out upward. If it is very hard, swing gently

and pull. (Fig 8)

4. Remove the Juicing Bowl by lifting it upward vertically. (Fig 9)

Fig 6 Fig 7 Fig 8 Fig 9

CLEANING & MAINTENANCE

1. Switch o and unplug the juicer.

Wash the disassembled parts (Fig 10) with water. If the meshes are clogged with pulp,

please use the provided cleaning brush to remove the excess ber.

Attention:

• Do not use iron wire brush, abrasive or sharp object tool to clean the unit.

• Please do not use water above 40°C.

3. In case there are any residues remained in the mouth of the pulp spout, please pull out the

silicone valve as shown in (Fig 11) below and clean under running water.

7. 6. 5. 4.

Fig 10

Fig 11

3. 2. 1.

Silicone Valve Pull to open

Press the silicone valve to close it property and tightly after cleaning.

4. To clean the seal ring in the center of the juicing bowl, please follow the steps as below :

a. Turn the Squeezing Bowl upside down for easier handling, Push the seal ring out

with your thumb (Fig 12a) and clean it with water.

b. After Cleaning, please put it back to the center hole. The small ribbed surface should

be should face upward (Fig.12b) Make sure the groove of the seal ring well t in

the squeezing bowl.

c. The big at size of the seal ring will be inside while the small and ribbed side is

outside the Squeezing Bowl. (Fig 12c)

5. Do not put the Power Base into water for cleaning. Wipe it with damp cloth only.

6. After cleaning, please dry the parts thoroughly and store them in a dry, cool place.

Fig 12a Fig 12b Fig 12c

STORAGE

USEFUL TIPS

NOTE:

Please make sure the unit and parts are dry before storing them.

1. Follow cleaning instructions to well maintain the unit before storage.

2. Tidy up the power cord set.

3. Keep the unit away from children’s easy access.

4. Store the unit and the accessories at a dry, cool place.

Not for Ice cubes.

The ingredient with long ber needs to

be cut down to 3 × 7 cm thin strips or 7 x

7 cm cubes.

The peel and pits/seeds must be

removed from oranges, lemons,

grapefruit and melons before use.

Do not use other accessory as a pusher.

Each juicing cycle must not longer than

20 minutes.

Never put the spoon, chopsticks into

the opening of the Chute, the juice

and pulp spouts.

Ice cubes are too hard. It may

damage the parts.

Long ber foods may easily block

the spout.

The hard pit or seeds may damage the

squeezing parts. The peel may block

the spout of pulp.

It may damage the juicer and

cause injury.

Working over time may cause damage to

the motor.

It may damage the juicer.

Item Warning Reason

TROUBLE SHOOTING

• If the supply cord is damaged, it must be replaced by the manufacturer or its service

agent or a similarity qualified person in order to avoid a hazard.

• WARNING: This appliance is not intended for use by persons (including children) with

reduce physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use of the appliance

by a person responsible for their safety.

Trouble Cause Solutions

The juicer

stops running

suddenly.

The juice yield

is low or juice

ows out of the

main housing.

Abnormal noise.

The Feeding

Chute cannot

be opened.

The container &

accessories are

dyed after use.

Too many

ingredients put

into the juicer.

Hard fruits or vegetables have

not been cut in small pieces.

The Bowl and the silicone valve

are not installed properly.

Parts cause extrusion sound

during squeezing.

There is too much pulp inside

the bowl.

There are hard foods

stuck inside.

The pulp mess is stuck.

Dyed parts are due to

natural color of specic

fruits/veggies.

Switch to “R” position instantly to make

the ingredients return upwards. If the

machine still stops running, please clean

the machine before using again.

Hard fruits and vegetables

(such as carrot) should be cut into

thin strips or small cubes before

putting into chute.

Please re-install the Bowl silicone

valve by referring to the installation

method.

The sound is caused by extrusion of

fruits and vegetables, which is normal.

Press switch to “R” setting to eject the

pulps backward.

Press switch to “R” to eject the

object backward.

Pour water into the Chute to soften

the stuck pulp mess overnight.

This is caused by natural coloring

and unavoidable.

SERVICE & IMPORTANT NOTICE

IMPORTED BY NATIONAL ELECTRICAL TRADERS

Table des matières

Manuels presse-agrumes populaires d'autres marques

GE 169201 Manuel utilisateur

Exquisit

Exquisit ZP 3001 WET Manuel utilisateur

Philips

Philips HR1851 Manuel utilisateur

Sam Cook

Sam Cook MASTERCHEF EXECUTIVE PSC-50 Manuel utilisateur

Termozeta

Termozeta spremiagrumi Manuel utilisateur

ElectrIQ

ElectrIQ WF1000 Manuel utilisateur

Bella

Bella WHOLE FRUIT JUICER Manuel utilisateur

HAEGER

HAEGER Little Juice CJ-025 006A Manuel utilisateur

Havells

Havells Fusion Manuel utilisateur

Siemens

Siemens MK554 SERIES Manuel utilisateur

Beper

Beper 90.302B Guide rapide

NATURSAFT

NATURSAFT 015.401.3 Manuel utilisateur

Moulinex

Moulinex BKB 2 Manuel utilisateur

Royal Catering

Royal Catering RCJU-01 Manuel utilisateur

camry

camry CR 4002 Manuel utilisateur

AIGOSTAR

AIGOSTAR 30HIM Manuel utilisateur

ZUMEX

ZUMEX MINEX Manuel utilisateur

Skymsen

Skymsen EX Manuel utilisateur