5
Table 1
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
AC Input Rating Amperes AWG Size of Cord
Equal to or but less than Length of Cord, Feet (Meter)
greater than 2.5(7.5) 50(15) 100(30) 150(45)
0 2 18 18 18 16
2 3 18 18 16 14
3 4 18 18 16 14
If the input rating of a battery charger is given in
watts rather than in amperes, the corresponding
ampere rating is to be determined by dividing the
wattage rating by the voltage rating-for example:
1,200 watts/120volt=10 Amperes
9. Do not operate battery charger with damaged
cord or plug，should replace them immediately.
10. Do not operate battery charger if it has received
a sharp blow, been dropped, or otherwise damaged
in any way; take it to a qualified serviceman.
11. Do not disassemble battery charger; take it to a
qualified serviceman when service or repair is
required.
Incorrect reassembly may result in a risk of
electric shock or fire.
12. To reduce risk of electric shock, unplug charger
from receptacle before attempting any maintenance
or cleaning. Removing the battery will not reduce
this risk.
13. Please read this Manual before using the battery
charger.
IMPORTANT SAFETY INSTRUCTIONS FOR USE
OF THE BATTERY AND BATTERY CHARGER
You must charge the battery before you use the
Nailer. Before using the model 504.4.04.013.01
battery charger, be sure to read all instructions and
cautionary statements on the battery and in this
manual.
REMEMBER : ONLY USE TOUA BATTERY
TYPE 504.4.04.011.01.
OTHER TYPES OF BATTERIES MAY BURST
AND CAUSE INJURY!
Follow these instructions to avoid the risk of injury:
WARNING
Improper use of the battery or battery charger
can lead to serious injury. Toavoid these injuries:
1. DO NOT disassemble the battery.
2. DO NOT incinerate the battery, even if it is
damaged or is completely worn out.
The battery can explode in a fire.
3. DO NOT short-circuit the battery.
4. DO NOT insert any objects into the battery
charger's air vents. Electric shock or
damage to the battery charger may result.
5. DO NOT charge outdoors. Keep the battery away
from direct sunlight and use only where
there is low humidity and good ventilation.
6. DO NOT charge when the temperature is below
50°F (10°C) or above 104°F (40°C).
7. DO NOT connect two battery chargers together.
8. DO NOT insert foreign objects into the hole for
the battery or the battery charger.
9. DO NOT use a booster transformer when charging.
10.DO NOT use an engine generator or DC power
to charge.
11. DO NOT store the battery or battery charger in
places where the temperature may
reach or exceed 104°F (40°C).
12. MUST TO DO operate charger on standard
household electrical power (120 volts).
Using the charger on any other voltage
may overheat and damage the charger.
13. MUST TO DO wait at least 15 minutes between
charges to avoid overheating the
charger.
14. MUST TO DO disconnect the power cord from
its receptacle and cut off the charger
power when the charger is not in use.
DISPOSAL OF THE EXHAUSTED BATTERY
WARNING
Do not dispose of the exhausted battery. The
battery must explode if it is incinerated. The
product that you have purchased contains a
rechargeable battery. The battery is recyclable.
At the end of it's useful life, under various state
and local laws, it may be illegal to dispose of
this battery into the municipal waste stream.
Check with your local solid waste officials for
details in your area for recycling options or proper
disposal.
EMPLOYER'S RESPONSIBILITIES
1. Ensure that this MANUAL is available to operators
and personnel performing maintenance.
2. Ensure that Nailers are used only when operators
and others in work area are wearing EYE PROTECTOR.
3. Enforce the use of EYE PROTECTOR by operators
and others in work area.
4. Keep Nailers in safe working order.
5. Maintain Nailers properly.
6. Ensure that Nailers which require repair are not
further used before repair.
SAVE THESE MANUAL AND MAKE THEM
AVAILABLE TO OTHER USERS AND OWNERS
OF THIS TOOL! 5
16
■ When not in use, the Nailer, fuel cell and battery
should be stored in a warm and dry place.
■Keep it out of reach of children.
4. WARNING LABEL
Change the WARNING LABEL if missing or damaged.
A new WARNING LABEL is available from a TOUA
authorized service center.
5. Maintenance chart
ACTION WHY HOW
Keep nailer mouth Promote operator Daily cleaning.
working properly. safety and efficient
Nailer operation.
Make sue all screw Avoid the nailer been Periodical
are tightening. damaged, make inspection.
sure the safety.
6. Operator troubleshooting
See page 18.
CAUTION
Repair, modification and inspection of TOUA
Power Tools must be carried out together with the
replacement parts list by an TOUA Authorized
Service Center.
In the operation and maintenance of power tools,
the safety regulations and standards prescribed
in each country must be observed.
MODIFICATIONS:
TOUA Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
SERVICE AND REPAIRS
WARNING
■ Only service personnel trained by TOUA,
distributor or employer shall repair the Nailer.
■ Use only parts supplied or recommended by
TOUA for repair.
All quality Nailers will eventually require servicing
or replacement of parts because of wear from normal
use.
NOTE
Specifications are subject to change without any
obligation on the part of TOUA.
