Total Protection Solutions LoadTrack LTE AC Series Manuel utilisateur

WARRANTY STATEMENT

During the applicable warranty period, any Total Protection Solutions™ surge protector

device which fails due to defect in materials, workmanship, or any electrical anomaly, in-

cluding lightning, shall be repaired or replaced at TPS’s discretion without charge. The ap-

plicable warranty period for the TPS surge protective device is outlined below in the War-

ranty Period section. The warranty period for any repaired devices or replacement devices

will be only the remaining portions of the original limited warranty.

Within a reasonable time, but in no case to exceed forty-five (45) days, user shall contact

Company's customer service department and obtain a Return Material Authorization (RMA)

before returning any products. User shall ship the product(s), with proof of purchase, to

Company freight prepaid.

The Company shall have no liability under this warranty for problems or defects directly or

indirectly caused by misuse of the Product, alteration of the Product (including removal of

any warning labels), accidents, improper installation, application, operation or improper

repair of the Product.

THIS WARRANTY REPRESENTS THE ENTIRE WARRANTY OF THE COMPANY.

ALL OTHER WARRANTIES EXPRESS OR IMPLIED, ORAL OR WRITTEN, INCLUD-

ING, BUT NOT LIMITED TO, THE WARRANTIES OF MERCHANT ABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.

The liability of the Company, at its sole option, under this warranty is expressly limited to

the replacement or repair of the defective part thereof. IN NO EVENT SHALL THE COM-

PANY BE LIABLE OR RESPONSIBLE FOR SPECIAL, INCIDENTAL, OR CONSE-

QUENTIAL DAMAGES OF ANY KIND OR CHARACTER, NOR SHALL ITS LIABIL-

ITY EVER EXCEED THE PURCHASE PRICE PAID TO COMPANY FOR SUCH DE-

FECTIVE PRODUCT.

This warranty is not transferable and may only be enforced by the original purchaser.

Claims under this warranty must be submitted to Total Protections Solutions, LLC. within

thirty (30) days of discovery of any suspected product defect.

Warranty Period

TK-LTExxx-yyA-DIN2, Fifteen Years Unlimited Free Replacement

(xxx is the voltage, yy is the amperage)

SAVE THESE INSTRUCTIONS

Note: If devices are received damaged, notify the shipping company immediately.

Retain containers and packing materials for inspection.

LoadTrack™ LTE Models

AC & DC Series/Parallel

Power Applications

LOADTRACK™ INSTALLATION, OPERATION AND MAINTENANCE MANUAL LOADTRACK™ INSTALLATION, OPERATION AND MAINTENANCE MANUAL

oad

rack

™

Surge

Protection

Device

Installation

Operation and

Maintenance

Manual

Total Protection Solutions, LLC.

TEL: 800.647.1911 www.TPSsurge.com

P.O. Box 3760 Winter Park, FL 32790

NOTICE: All instructions and measurements must be completed by a qualified electrician in

accordance with the National Electric Code and/or other applicable state and local codes. The U.S.

National Electric Code and/or applicable state/local requirements supersede these instructions.

IMPORTANT SAFETY INSTRUCTIONS

Page: 3

CAUTION: HAZARDOUS VOLTAGES PRESENT

Improper installation or misapplication of these devices may result in serious injury to the installer

and/or damage to electrical system(s) or related equipment. Read and understand all instructions

before commencing with the installation. Protective eyewear should be worn during the installa-

tion process.

Page: 2

Units must be connected to the electrical service with appropriate ampacity Class T Fuse,

rated 300 V, or with a breaker with appropriate ampacity for the specific unit.

Equipment Safety Grounds MUST be run separately - not through the traces of the Surge

Protection Device.

INSTALLATION

1) This document provides detailed information on how to install and operate the LoadTrack of

Surge Protective Devices (SPDs).

2) Units should be installed per the information and illustrations provided herein. See above

WARNING.

3) The LoadTrack Series of Surge Protective Devices are installed/connected in either series or

parallel with the line and the equipment to be protected.

4) Identified or indicated Leads/Wires must be connected exactly with respect to the power

feeding/supplying the SPD and equipment. Failure to do so may result in damage to the SPD,

the equipment/system or pose a danger to personnel.

5) Incorrect installation may significantly impair the performance of the SPD. It is particularly

important that all installation procedures and guidelines be followed exactly.

6) Before starting any installation procedures, verify service voltages (AC or DC) with a volt

meter to ensure that the correct model has been selected for the supply voltage.

7) DO NOT INSTALL THE SPD IF MEASURED VOLTAGE EXCEEDS UNIT RATINGS.

8) The SPD MUST BE mounted in an enclosure to assure personnel safety from exposed

terminals.

9) REMOVE POWER FROM ELECTRICAL SYSTEM PRIOR TO INSTALLATION.

10) The SPD should be positioned as the last device in the circuit prior to protected

equipment.

11) The SPD Line/Load designations are for orientation purposes only and do not effect the

install.

ANY ALTERATIONS, TAMPERING, MISUSE OR UNAUTHORIZED REPAIRS OF THIS PRODUCT

WILL VOID ITS ORIGINAL FACTORY WARRANTY.

WARNING

WIRING DIAGRAMS

NOTE: Circuit Protection NOT required for neutral application.

If two (2) hots are used a second interrupt device is required.

Load out

Line in

Load out

Line2 / N in

Line2 / N out

Ground out

Not a safety

Ground

Not a safety

Ground

Series

Parallel

(Fuse incoming lines)

(Fuse incoming

lines) Line in

Line2 / N in

(Fuse incoming lines)

Line

Line2 / N

(Fuse incoming lines)

Line

Line2 / N

12) Mechanically mount the SPD utilizing the mounting tabs or attach to din rail.

13) For Series (AC) Applications

a) Connect "LINE" Side:

∗System Ground to the terminal labeled "G".

* Neutral or Line 2 wire to the terminal labeled "L2" .

* HOT wire to the terminal labeled "L1".

b) Connect "LOAD" Side:

* System Ground to the terminal labeled “G" (connect safety ground directly to enclosure

ground).

* Neutral or Line 2 wire to the terminal labeled "L2".

* HOT wire to the terminal labeled “L1".

14) For parallel (AC) Applications, keeping leads as short as possible -

∗System Ground, to the terminal labeled "G".

* Neutral or Line 2 wire to the terminal labeled "L2".

* HOT wire to the terminal labeled "L1".

Note: In parallel applications, units are not current limited as they are in series applications.

For parallel applications, unused output terminals are left empty, no plugs are provided.

15) ENSURE THAT ALL CONNECTIONS ARE CORRECT BEFORE ENERGIZING.

16) Apply power (energize). LED indicator should illuminate. If light fails to illuminate contact

supplier. If LED is out, unit requires service.

17) Keep this MANUAL in a safe dry place for future reference.

Ce manuel convient aux modèles suivants

Autres manuels Total Protection Solutions Parafoudre

Total Protection Solutions

Total Protection Solutions TK-CT2-190TLP1-TB Manuel utilisateur

Total Protection Solutions

Total Protection Solutions ComTrack TK-CT2-PHONE-RJ Manuel

Total Protection Solutions

Total Protection Solutions LoadTrack TK-LTL120P-30A Manuel utilisateur

Total Protection Solutions

Total Protection Solutions ServiceTrack ST 080 Manuel utilisateur

Total Protection Solutions

Total Protection Solutions 80 Manuel utilisateur

Total Protection Solutions

Total Protection Solutions ComTrack TK-CT2-190TLP4-RJ-T1/E1-C Manuel utilisateur

Total Protection Solutions

Total Protection Solutions 80 Manuel utilisateur

Total Protection Solutions

Total Protection Solutions 160 Manuel utilisateur

Total Protection Solutions

Total Protection Solutions 200 Manuel utilisateur

Total Protection Solutions

Total Protection Solutions ComTrack TK-CT2-DB9 Manuel utilisateur

Manuels Parafoudre populaires d'autres marques

ELAC

ELAC ProteK PR91-W Manuel utilisateur

Tsubaki

Tsubaki TSM4000M1 Manuel utilisateur

QVS

QVS PP134C Manuel utilisateur

CyberPower

CyberPower CSP604T Manuel utilisateur

Davis Instruments

Davis Instruments Radio Surge Protector Manuel utilisateur

M-system

M-system MGA-100 Manuel utilisateur

CyberPower

CyberPower CSP706T Manuel utilisateur

CyberPower

CyberPower B300WRC1 Manuel utilisateur

M-system

M-system MGD-24 Manuel utilisateur

Leviton

Leviton 51120-3R Manuel utilisateur

Panamax

Panamax MAX 5400-EX Manuel utilisateur

CyberPower

CyberPower B1006T Manuel utilisateur

OBO Bettermann

OBO Bettermann ÜSM-20-230I1PE65 Manuel utilisateur

Minuteman

Minuteman MMS7120RCT Manuel utilisateur

Leviton

Leviton 52412-DS3 Manuel utilisateur

Savio

Savio LZ-07 Manuel utilisateur

Siemens

Siemens HNM3M120 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric LITOL LTM-125RF Manuel utilisateur