Toshiba Strata DK Backup Manuel de service

Strata® DK

Technical Bulletin

Toshiba America Information Systems, Inc.

Telecommunication Systems Division

9740 Irvine Blvd., Irvine, CA 92618-1697 (949) 583-3700

http://telecom.toshiba.com

726+,%$

4031068

DK424 to DK424i Upgrade

Procedure Using DKi Admin

This bulletin describes how to upgrade the DK424 to a DK424i system. It also lists the upgrade paths for

various DK424 processors, provides system capacity and line considerations, along with reconfiguration

examples and blank configuration worksheets.

Upgrade Considerations

Upgrade Paths – The following is a list of possible DK424 to DK424i upgrade paths:

♦RCTU A processors (R1~4.x) >> B1, B2, B3, B5 processors

♦RCTU B processors (R1~4.x) >> B2, B3, B5 processors

♦RCTUC/D processors (R1~4.x) >> B3 & B5 processors

♦RCTU E/F processors (R3~4.x) >> B5 processors

Note For a specific list of all processors, see Page 6 of this bulletin.

System Capacity Verification – Make sure the DK424i system you are upgrading to provides enough

PCB slots, station ports, and CO lines to match the existing DK424 system (see tables below).

DK424i Maximum System Capacities with only Digital T1/PRI Line PCBs

B1CU B2CAU/B2CBU B3CAU/B3CBU B5CAU/B5CBU

1 Cabinet

8 Universal slots

56 Stations Max.

32 T1/PRI lines Max.

64 Stations & Digital lines

2 Cabinets

14 Universal slots

112 Stations Max.

120 T1/PRI lines Max.

128 Stations & Digital lines

3 Cabinets

28 Universal slots

192 Stations Max.

120 T1/PRI lines Max.

248 Stations & Digital lines

5 Cabinets

48 Universal slots

336 Stations Max.

196 T1/PRI lines Max.

432 Stations & Digital lines

DK424i Maximum System Capacities with only Analog Line PCBs

B1CU B2CAU/B2CBU B3CAU/B3CBU B5CAU/B5CBU

TBDK-0042

November 2000

November 2000 Configuring DK424i Cabinets with DK424 PCBs

DK424 to DK424i Upgrade Procedure Using DKi Admin

2 of 7

Configuring DK424i Cabinets with DK424 PCBs

RCTU, R1~R3 Software with Tie and/or DID Lines

♦When installing PCBs in the DK424i cabinets, all PCBs must be installed in the same order in relation

to each other as they were in the DK424 cabinets. You may have to skip slots in the new cabinets to

place RDTU PCBs into the allowed slots.

♦Only install the PCBs that currently exist in the DK424 cabinets into the DK424i cabinets –do not add

more line or station PCBs during the upgrade. The only exception to this rule is that you can add an

RSIU, PIOU, PIOUS, RSSU.

RCTU, R1~R3 Software Without Tie/DID, or any R4.x Software With or

Without Tie/DID Lines

♦Only install the PCBs that currently exist in the DK424 cabinets into the DK424i cabinets –do not add

more line or station PCBs during the upgrade. The only exception to this rule is that you can add an

RSIU, PIOU, PIOUS, RSSU.

♦When installing PCBs in the DK424i cabinets, all station PCBs and the RATU must be installed in the

same order in relation to other station PCBs as they were in the DK424 cabinets.

♦When installing PCBs in the DK424i cabinets, all CO line PCBs must be installed in the same order in

relation to other CO line PCBs as they were in the DK424 cabinets.

♦When moving station PCBs from DK424 to DK424i cabinets, you do not have to installed them in the

same order in relation to CO line PCBs, and vice-versa .

♦Do not skip slots except when necessary for RDTU, RPTU, and RWIU. Make sure these PCBs are

installed in the correct cabinet slot per Worksheet 6 of the Strata DK I&M Manual, Chapter 6 –

DK424i Configuration.

♦PIOU, PIOUS, RSSU, etc., can be installed in any DK424i slot that does not conflict with RDTU,

RPTU or RWIU vacant slots. These PCBs do not have to be installed in any order corresponding to

where they were installed in DK424 cabinets. The RSIU must be installed in slot S101.

1 Cabinet

8 Universal slots

56 Stations Max.

32 CO lines Max.

64 Stations & Analog lines

2 Cabinets

14 Universal slots

104 Stations Max.

120 CO lines Max.

112 Stations & Analog lines

3 Cabinets

28 Universal slots

192 Stations Max.

120 CO lines Max.

248 Stations & Analog lines

5 Cabinets

48 Universal slots

336 Stations Max.

200 CO lines Max.

376 Stations & Analog lines

November 2000 Configuring DK424i Cabinets with DK424 PCBs

DK424 to DK424i Upgrade Procedure Using DKi Admin

Preliminary andConfidential

3 of 7

Reconfiguration Example: The following tables show two examples of how to load DK424i cabinet slots from

the same DK424, RCTU E/F R4, system.

T=Telephone type PCB

L=CO Line type PCB

Existing DK424 Cabinets Example 1, DK424i Cabinets Example 2, DK424i Cabinets

Slot PCB T/L No. Slot PCB T/L No. Slot PCB T/L No.

R11 RCTUE B101 B5CAU B101 B5CAU

RCTU RCTUF B102 B5CBU B102 B5CBU

S11 RSIU S101 RSIU S101 RSIU

S12 PDKU T1 S102 PDKU T1 S102 PDKU T1

S13 RSTU T2 S103 RDTU L1 S103 RSTU T2

S14 PEKU T3 S104 VACANT L1 S104 PEKU T3

S15 RDTU L1 S105 RCOU L2 S105 RDTU L1

S16 VACANT L1 S106 RSTU T2 S106 VACANT L1

S21 RCOU L2 S107 RPTU L3 S107 RCOU L2

S22 PEKU T4 S108 VACANT L3 S108 PEKU T4

S23 RPTU L3 S201 PEKU T3 S201 PDKU T5

S24 VACANT L3 S202 PEKU T4 S202 PDKU T6

S25 PDKU T5 S203 RCOU L4 S203 RPTU L3

S26 PDKU T6 S204 RCOU L5 S204 VACANT L3

S27 RCOU L4 S205 REMU L6 S205 RCOU L4

S28 RCOU L5 S206 PDKU T5 S206 PDKU T7

S31 REMU L6 S207 PDKU T6 S207 RCOU L5

S32 PDKU T7 S208 PDKU T7 S208 RSTU T8

S33 RSTU T8 S209 RSTU T8 S209 PEK T9

S34 PEKU T9 S210 PEKU T9 S210 PDKU T10

S35 PDKU T10 S301 RDTU L7 S301 RDSU T11

S36 RDSU T11 S302 VACANT S302 REMU L6

S37 PDKU T12 S303 PDKU T10 S303 RDTU L7

S38 PDKU T13 S304 RDSU T11 S304 VACANT L7

S41 RDTU L7 S305 PDKU T12 S305 PDKU T12

S42 VACANT L7 S306 PDKU T13 S306 PDKU T13

S43 PDKU T14 S307 PDKU T14 S307 PDKU T14

S44 RDDU L8 S308 PESU T15 S308 RDDU L8

S45 PESU T15 S309 PDKU T16 S309 RESU T15

S46 PDKU T16 S310 RDDU L8 S310 RCOU L9

S47 RSTU T17 S401 RCOU L9 S401 PDKU T16

S48 RCOU L9 S402 RSTU T17 S402 RSTU T17

S51 PDKU T18 S403 PDKU T18 S403 PDKU T18

S52 S404 S404

S53 S405 S405

November 2000 DKi Admin Upgrade Procedure (DK424 to DK424i)

DK424 to DK424i Upgrade Procedure Using DKi Admin

4 of 7

DKi Admin Upgrade Procedure (DK424 to DK424i)

1. When upgrading from a DK424 (RCTU) to DK424i (BxCU), use DKi Admin to download the

complete RCTU database (F2 then F3 from Backup/Restore Data).

Note After the download, use the DKi Admin “Transfer DK Data”function to transfer this data to a

floppy in case you need to restore the data back to the RCTU processor.

2. Before proceeding with DKi Admin, complete either the On-site Upgrade or Off-site Upgrade:

Important! Make sure all PCBs are installed and/or programmed correctly with Program 03 in the

DK424i before uploading data to the DK424i processor.

3. Connect the DKi Admin PC to the TTY port in the DK424i base cabinet and then set up the TTY

port/communications parameters using the programming telephone.

4. Go to the Select Customer menu and select the RCTU data that was downloaded in Step 1 above. (The

data you want to upload to the new DK424i processor).

5. Go to the Backup/Restore menu and type the DK Code 0000.

6. When you see the “DK System Program File screen”press F5 and follow the Processor Conversion

prompts to upgrade and send data to the DK424i processor.

7. Step 6 prompts you to send the RCTU data to the BxCU processor and then pull it back. Once the data

is pulled back, go back to the “Select Customer”menu and reselect the customer database; then check

the cabinet diagram.

Important! After the upgrade is complete, you must use DKi Admin to re-set Program 12-9

(recommended value is 04 sec.) and all slot related programs (Prg. 19, *42-1~2, and *60).

On-site

Upgrade

1. Install the new BxCU processor and all other PCBs from the DK424 cabinets

into the DK424i cabinets and then initialize the BxCU from the programming

telephone (follow the PCB configuration rules shown on the previous page).

2. After initialization, use the programming telephone to check/enter Program 03

PCB codes for each cabinet slot.

Off-site

Upgrade

1. Install the programming telephone and TTY port PCB into a DK424i base

cabinet. Install the new BxC processor into the DK424i base cabinet and

initialize it from the programming telephone.

2. After initialization, use the programming telephone to enter Program 03 PCB

codes for each cabinet slot (follow the PCB configuration rules shown on the

previous page).

November 2000 DKi Admin Upgrade Procedure (DK424 to DK424i)

DK424 to DK424i Upgrade Procedure Using DKi Admin

Preliminary andConfidential

5 of 7

Upgrade Configuration Worksheet (copy additional sheets as necessary)

DK424 Cabinets DK424i Cabinets

Cab 1 Slots PCB T/L Cab 4 Slots PCB T/L Cab 1 Slots PCB T/L Cab 4 Slots PCB T/L

R11 S51 B101 S401*

RCTU S52 B102 S402

S11 S53 S101 S403*

S12 S54 S102 S404

S13 S55 S103* S405*

S14 S56 S104 S406

S15 S57 S105* S407

S16 S58 S106 S408

S107* S409

Cab 2 Slots PCB T/L Cab 6 Slots PCB T/L

S21 S61 Cab 2 Slots PCB T/L Cab 5 Slots PCB T/L

S22 S62 S201* S501*

S23 S63 S202 S502

S24 S64 S203* S503*

S25 S65 S204 S504

S26 S66 S205* S505*

S27 S67 S206 S506

S28 S68 S207 S507

S208 S508

Cab 3 Slots PCB T/L Cab 7 Slots PCB T/L S209 S509

S21 S71 S210 S510

S22 S72

S23 S73 Cab 3 Slots PCB T/L

S24 S74 S301*

S25 S75 S302

S26 S76 S303*

S27 S77 S304

S28 S78 S305*

S306

Cab 4 Slots PCB T/L S307

S41 S308

S42 S309

S43 S310

S44

S45

S46

S47

S48

Notes:

T=Telephone type PCB

L=CO line type PCB

*= Allowed T1/PRI slots

The Base cabinet allows Spkr

OCA and DIU data with PDKU

in all slots; expansion cabinets

provide these features in slots

S_01~S_06 only.

Last available slot: B1C=S108,

B2C=206, B3C=310, and

B5C=510.

November 2000 Strata DK Processor Upgrade Paths

DK424 to DK424i Upgrade Procedure Using DKi Admin

6 of 7

Strata DK Processor Upgrade Paths

DK14 (contains DK Release 3.1 software)

♦Upgrade DK14 to: DK16e or DK40 or DK40i or RCTUA3 or RCTUBA3/RCTUBB3 or RCTUC3/

D3 or RCTUC3/D4 or RCTUE3/F3 or RCTUE3/F4 or B1CU or B2CAU/B2CBU or B3CAU/B3CBU

or B5CAU/B5CBU.

DK16e (contains DK Release 3.1 software)

♦Upgrade DK16e to: DK40 or DK40i or RCTUA3 or RCTUBA3/RCTUBB3 or RCTUC3/D3 or

RCTUC3/D4 or RCTUE3/F3 or RCTUE3/F4 or B1CU or B2CAU/B2CBU or B3CAU/B3CBU or

B5CAU/B5CBU.

DK40 (contains DK Release 3.1 software)

♦Upgrade DK40 to: DK40i or RCTUA3 or RCTUBA3/RCTUBB3 or RCTUC3/D3 or RCTUC3/D4

or RCTUE3/F3 or RCTUE3/F4 or B1CU or B2CAU/B2CBU or B3CAU/B3CBU or B5CAU/B5CBU.

DK40i (contains DK424 Release 4.3 software)

♦Upgrade DK40i to: RCTUA4 or RCTUBA3/RCTUBB4 or RCTUC3/D4 or RCTUE3/F4 or B1CU or

B2CAU/B2CBU or B3CAU/B3CBU or B5CAU/B5CBU.

DK280, RCTU R1/R2 (contains DK Release 1.0 or Release

2.0 software)

♦Upgrade RCTUA1 to: RCTUB2 or RCTUBA3/RCTUBB3 or RCTUBA3/RCTUBB4 or RCTUC1/

D2 or RCTUC3/D3 or RCTUC3/D4 or RCTUE3/F3 or RCTUE3/F4 or B1CU or B2CAU/B2CBU or

B3CAU/B3CBU or B5CAU/B5CBU.

♦Upgrade RCTUB2 to: RCTUBA3/RCTUBB3 or RCTUBA3/RCTUBB4 or RCTUC1/D2 or or

RCTUC3/D3 or RCTUC3/D4 or RCTUE3/F3 or RCTUE3/F4 or B2CAU/B2CBU or B3CAU/B3CBU

or B5CAU/B5CBU.

♦Upgrade RCTUC1/D2 to: RCTUC3/D3 or RCTUC3/D4 or RCTUE3/F3 or RCTUE3/F4 or B3CAU/

B3CBU or B5CAU/B5CBU.

DK424, RCTU R3.x (contains DK Release 3.0 or Release 3.2

software)

♦Upgrade RCTUA3 to: RCTUBA3/RCTUBB3 or RCTUC3/D3 or RCTUC3/D4 or RCTUE3/F3 or

RCTUE3/F4 or B1CU or B2CAU/B2CBU or B3CAU/B3CBU or B5CAU/B5CBU.

♦Upgrade RCTUBA3/RCTUBB3 to: RCTUC3/D3 or RCTUC3/D4 or RCTUE3/F3 or RCTUE3/F4

or B2CAU/B2CBU or B3CAU/B3CBU or B5CAU/B5CBU.

♦Upgrade RCTUC3/D3 to: RCTUC3/D4 or RCTUE3/F3 or RCTUE3/F4 or B3CAU/B3CBU or

B5CAU/B5CBU.

♦Upgrade RCTUE3/F3 to: RCTUE3/F4 or B5CAU/B5CBU.

November 2000 DK424, RCTU R4.x (contains DK Release 4.0, Release 4.15 or Release 4.3 software)

DK424 to DK424i Upgrade Procedure Using DKi Admin

Preliminary andConfidential

7 of 7

DK424, RCTU R4.x (contains DK Release 4.0, Release 4.15

or Release 4.3 software)

♦Upgrade RCTUA4 to: RCTUBA3/RCTUBB4 or RCTUC3/D4 or RCTUE3/F4 or B1CU or B2CAU/

B2CBU or B3CAU/B3CBU or B5CAU/B5CBU.

♦Upgrade RCTUBA3/RCTUBB4 to: RCTUC3/D4 or RCTUE3/F4 or B2CAU/B2CBU or B3CAU/

B3CBU or B5CAU/B5CBU.

♦Upgrade RCTUC3/D4 to: RCTUE3/F4 or B3CAU/B3CBU or B5CAU/B5CBU.

♦Upgrade RCTUE3/F4 to: B5CAU/B5CBU.

DK424i, BxC (contains DK Release 4.3 software)

♦Upgrade B1CU to: B2CAU/B2CBU or B3CAU/B3CBU or B5CAU/B5CBU.

♦Upgrade B2CAU/B2CBU to: B3CAU/B3CBU or B5CAU/B5CBU.

♦Upgrade B3CAU/B3CBU to: B5CAU/B5CBU.

Autres manuels pour Strata DK Backup

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Toshiba Logiciel

Toshiba

Toshiba PFW008U-1ABW Manuel utilisateur

Toshiba

Toshiba Strata CIX SIP Trunking Manuel utilisateur

Toshiba

Toshiba Strata CIX SoftIPT 2.1.2 Manuel utilisateur

Toshiba

Toshiba Strata CS Release 7.0 Manuel

Toshiba

Toshiba STRATA CIX Manuel du propriétaire

Toshiba

Toshiba RSM 100 Manuel utilisateur

Toshiba

Toshiba Strata CTX SoftIPT Manuel de service

Toshiba

Toshiba Strata CIX Database Assistant Manuel de service

Toshiba

Toshiba MEG50AS Manuel utilisateur

Toshiba

Toshiba STRATA CIX Net Server Manuel de service

Toshiba

Toshiba VIPedge Manuel utilisateur

Toshiba

Toshiba e-STUDIO Printer/Fax/Scanner/Copier Manuel utilisateur

Toshiba

Toshiba Strata CTX Insight CTX Manuel utilisateur

Toshiba

Toshiba T-PSV Manuel utilisateur

Toshiba

Toshiba TDP-TW350U Manuel utilisateur

Toshiba

Toshiba AF 512E Mode d’emploi

Toshiba

Toshiba STRATA CIX Remote Call Control Manuel de service

Toshiba

Toshiba STRATA CIX Manuel de service

Toshiba

Toshiba Strata CS Manuel utilisateur

Toshiba

Toshiba Strata AirLink DK424 Manuel utilisateur

Toshiba

Toshiba Strata CTX ACD Application Manuel utilisateur

Toshiba

Toshiba IPedge Software Release R1.5 Manuel utilisateur

Toshiba

Toshiba Strata CIX WinCIX Manuel de service

Toshiba

Toshiba STRATA CIX Remote Call Control Manuel utilisateur

Manuels Logiciel populaires d'autres marques

COMPRO

COMPRO COMPROFM Manuel utilisateur

Muratec

Muratec OFFICEBRIDGE ONLINE Manuel utilisateur

Oracle

Oracle Contact Center Anywhere 8.1 Manuel utilisateur

Adobe

Adobe 65007312 - Photoshop Lightroom Manuel

Avaya

Avaya NULL One-X for RIM Blackberry Manuel utilisateur

HP ProLiant BL420c Manuel utilisateur

PS Audio

PS Audio PowerPlay Manuel du propriétaire

Brady

Brady LOCKOUT PRO 3.0 Manuel de service

Avaya

Avaya Interaction Center Manuel utilisateur

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manuel

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manuel utilisateur

Oracle

Oracle Application 9i Manuel utilisateur

Acer

Acer RDM Manuel utilisateur

Canon

Canon Vixia HF21 Manuel utilisateur

Canon

Canon ZR950 Manuel utilisateur

Samsung

Samsung Auto Backup Manuel utilisateur

Polycom

Polycom Vortex EF2201 Instructions d'installation et d'utilisation

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manuel utilisateur