Toshiba IK-HD1 Manuel utilisateur

2007.05.30

RS-232C communication specifications for IK-HD1C



1．Communication data specifications



Synchronization system Asynchronous

Baud rate 9600 bps / 19200 bps

Data length 8 bits

Parity None

Start bit 1 bit

Stop bit 1 bit

Direction of transmission LSB first

Handshake function None



2．Terminal names ( camera side )



Name Direction of signal

TXD Camera to PC

RXD PC to camera

GND −



3．Method of connection

Camera PC（RS-232C）

TXD RXD

RXD TXD

GND GND

4-3. Do not transmit a next command from the time you transmit a command code to the camera until you finish receiving a return code.

Allow for at least 50mS from the time you receive a return code until you transmit a next command.

4-2. If the product fails to receive up to the 4th byte of data within about two seconds after receiving the 1st byte of command code from

the PC, the product will judge the status as a communication error about the reception, and transmit a return code (15 01FF FF).





Camera to PC













PC to camera



 1st byte 2nd byte 3rd byte 4th byte



 100µS or more

Command



4-1. Camera communications consist of receiving a four-byte command code from the PC and then

4.Communication procedure

communicating a four-byte return code from the camera.

* The same is true in the case of an overrun error or framing error. About two seconds after such an error occurs, the product will

transmit a return code (15 01 FF FF).

* Transmitting any of the following commands before a return code transmission will cause that command to be ignored

(unidentified)..

 1st byte 2nd byte 3rd byte 4th byte



Approx.100μS to 50mS

Return

Max 2 sec



5. Command code (PC to camera)

Transmitted dataItem

1st byte 2nd byte 3rd Byte 4th byte

Actions

SWITCH 4BH 01H FFH FFH DISP Functions in the same way as the front switches.

4BH 02H FFH FFH PAGE Note 1: The same as when the DATA UP is pressed for one

second.

4BH 03H FFH FFH MENU UP Note 2: The same as when the DATA DOWN is pressed for

one second.

4BH 04H FFH FFH MENU DOWN Note 3: The same as when the MENU UP is pressed for one

second.

4BH 05H FFH FFH DATA UP

4BH 06H FFH FFH DATA DOWN

4BH 07H FFH FFH AWB START(Note 1)

4BH 08H FFH FFH ABB START(Note 2)

4BH 09H FFH FFH ASHD START(Note 3)

4BH 0AH FFH FFH DATA PRESET(Note 4)

4BH 0BH FFH FFH FILE

Note 4: Remote presetting does not change the baud rate

setting. All other items function in the same wayas

the presetting actions made by pressing the MENU

DOWN and DATA DOWN simultaneously. This

returns the product to its initial settings.

4BH 0DH FFH FFH KEY LOCK ON Functions in the same way as the KEY LOCK switch on the

rear panel.

4BH 0EH FFH FFH KEY LOCK OFF

4BH

１１ H FFH FFH GAIN Functions in the same way as the front switches.

05H ADDRESS

FFH FFH MEMORY DATA READ REQUEST

For ADDRESS, see 11.”ADDRESS&DATA (1st byte=05H, 53H).”

53H ADDRESS

DATA(L) DATA(H) MEMORY DATA WRITE REQUEST

For ADDRESS and DATA, see 11.”ADDRESS&DATA (1st byte=05H, 53H).”

MEMORY

FFH ADDRESS FFH FFH CAMERA STATUS READ REQUEST

For ADDRESS, see 13.”ADDRESS&DATA (1st byte=FFH).”

zThe tables in 10 and 11 (on page 7 and later) notate the data H first, then L. You should however transmit the data L first, then H.

5-1.OperatingKEYLOCK

IfyoutransmittheKEYLOCKcommand(4B0DFFFFor4B0EFFFF),youcannotoperatebyKEYLOCKswitch

ontherearpaneluntilthefollowingactionsareperformed.

・DisconnectacableofRS-232C.

・Turnoffthecomputer.

・Afterturningoffthecamera,turnitonagain.



5-2.MEMORYDATAREAD／WRITE

１）MEMORYDATAREADREQUEST（05ADDRESSFFFF）

-ThisfunctionisusedtoreaditemsthatcanbeconfiguredbyOSD（two-bytedata）.

-ForthecontentsofADDRESSandDATA,see11.”ADDRESS&DATA(1 ｓｔbyte=05H,53H).”

-Thisfunctionreadsthecontentsofthespecifieditem.



２）MEMORYDATAWRITEREQUEST（53ADDRESSDATA(L)DATA(H)）

-ThisfunctionisusedtorewritethecontentsofitemsthatcanbeconfiguredbyOSD（two-bytedata）.

-ForthecontentsofADDRESSandDATA,see11.”ADDRESS&DATA(1 ｓｔbyte=05H,53H).”

-Thisfunctionrewritesthecontentsofthespecifieditem.

- During AWB(while the data in AUTO READ is 01H)，the product will not accept the MEMORY DATA WRITE

REQUESTcommand.(Theproductwillreturnthereturncodeduetothecameramodeerror.

See6.”Returncode.”)



３）MEMORYDATAREADREQUEST（FFADDRESSFFFF）

-Thisfunctionisusedtoreadthestatusdataofthecamera(two-bytedata).

-ForthecontentsofADDRESSandDATA,seethecontentsof12.”ADDRESS&DATA(1stbyte＝FFH).”

6．Returncode（CameratoPC）

Returncode

Item

1stbyte 2ndbyte 3rdbyte 4thbyte

Meaning

06H Transmitted

data

2ndbyte

Transmitted

data

3rdbyte

Transmitted

data

4thbyte

Transmitteddata,1stbyte

≠05H，≠FFH

06H ADDRESS DATA(L) DATA(H) Transmitteddata,1stbyte

＝05H

NORMAL

FFH ADDRESS DATA(L) FFH Transmitted data  1st byte＝

FFH

ERROR 15H 01H FFH FFH Invaliddata(1st,2ndbyte)

 15H 02H FFH FFH Invaliddata(3rd,4thbyte)

 15H 03H FFH FFH Cameramodeerror

Youhavespecifiedacommand

which cannot be executed in

the current camera mode or

whichcannotproduceanything

significant.

 15H 04H FFH FFH A communication error has

occurred (an overrun error or

framingerror).

 15H 05H FFH FFH Time-out

Acameramodeerror(15H03HFFHFFH)canbecausedbyanyofthefollowing:

Command

category Commanditem Camerastatusthatcausesamodeerror

Operation

switchsystem DISP -AWB,ABB,ASHDbeingexecuted.

 PAGE -AWB,ABB,ASHDbeingexecuted.

 MENUUP -Colorbarscreenon -Camerascreenon 

-AWB,ABB,ASHDbeingexecuted.

 MENUDOWN ditto

 DATAUP - Color bar screen on - Camera screen on - AWB, ABB, ASHD being

executed.

 DATADOWN ditto

 FILE -Colorbarscreenon-AWB,ABB,ASHDbeingexecuted.

 AWBSTART -TheWBmodeisinamodeotherthanAWB.-Colorbarscreenon-Menu

screenon-AWB,ABB,ASHDbeingexecuted.

 ABBSTART - Color bar screen on - Camera screen on - AWB, ABB, ASHD being

executed.

 ASHDSTART -SHADINGmodeisinamodeotherthanSET.-Colorbarscreenon-Menu

screenon-AWB,ABB,ASHDbeingexecuted.

 DATAPRESET - Color bar screen on - Menu screen on - AWB, ABB,ASHDbeing

executed.

MEMORY

DATAWRITE Other than SCENE

FILE -AWB,ABB,ASHDbeingexecuted.

MEMORY

DATAWRITE SCENEFILE -Colorbarscreenon-AWB,ABB,ASHDbeingexecuted.



7．AWB

１） Tostart AWB,takeanimage ofawhitesubject andtransmit anAWBSARTcommandunderthefollowing

conditions:

●TheWBmodeshouldbeAWB.

●Thecamerascreen(aliveimage)shouldbeon.（TheOSDPAGEdatashouldbe00H.）

●AWB，ABB，SHDshouldnotbeunderexecution.（AUTOREADdatashouldnotbe01H，0BH，0FH）



２）FortheAWBstatus(whetherinprogressorcomplete)andthefinalresult,readthecontentsofAUTOREADby

usingtheMEMORYDATAREADREQUEST(FF03FFFF)command.Forthecausesoferrors,refertothefollowing:

NG  :AWBwillnotbecompletedwithinaspecifiedtime.

CTEMPHIGH :Colortemperatureistoohigh.

CTEMPLOW :Colortemperatureistoolow.

LEVELHIGH :Theleveloftheimageintheareaistoohigh.

LEVELLOW :Theleveloftheimageintheareaistoolow.

NOTAVAILABLE:AWBSTARTcommandhasbeentransmittedwhentheconditionsspecifiedin1)areunmet.



8．ABB

1)TostartABB,transmitanABBSTARTcommandunderthefollowingconditions:

●Thecamerascreen(aliveimage)shouldbeon.（TheOSDPAGEdatashouldbe00H.）

●AWB，ABB，SHDshouldnotbeunderexecution.（AUTOREADdatashouldnotbe01H，0BH，0FH.）



2)FortheABBstatus(whetherinprogressorcomplete)andthefinalresult,readthecontentsofAUTOREADby

usingtheABBMEMORYDATAREADREQUEST（FF03FFFF）command.Forthecauseoferrors,refertothe

following:

NG  :ABBwillnotbecompletedwithinaspecifiedtime.

CLOSELENS :Thelensirisisopen.Closethelensiris.



9．ASHD(AUTOSHADING)

1)TostartAUTOSHADING,transmitanASHDSTARTcommandunderthefollowingconditions:

●SHADINGsettingofOPTIONshouldbeSET.(OPTIONSHADINGMODEdatashouldbe00H.)

●Thecamerascreen(aliveimage)shouldbeon.（OSDPAGEdatashouldbe00H.）

●AWB，ABB，SHDshouldnotbeunderexecution.(AUTOREADdatashouldnotbe01H，0BH，0FH.）



2)FortheSHDstatus(whetherinprogressorcomplete)andthefinalresult,readthecontentsofAUTO

READbyusingtheMEMORYDATAREADREQUEST（FF03FFFF）command.Forthecausesoferrors,refertothe

following:

SHDLIMIT:Automaticshadingcorrectionoperationfinished,however,thecorrectionnecessaryexceeds

thecameraʼsrangesothemaximumpossiblevalueisapplied.

LEVELHIGH  :Theleveloftheimageintheareaistoohigh.

LEVELLOW :Theleveloftheimageintheareaistoolow.

SHDNG  :AUTOSHADINGwillnotbecompletedwithinaspecifiednumberoftimes.

NOTAVALABLE :ASHDSTARTcommandhasbeentransmittedwhentheconditionsspecified  

in1)areunmet.



10．Other

TheproductwillstorethedataevenifthedatachangesmadeinMEMORYDATAWRITEREQUEST（53ADDRESS

DATA(L)DATA(H)）isnotenabledinthecameramodeatthetime ofthechange.Thenexttimetheproduct

switchestothemodeinwhichthedataisenabled,thedatawillbereflectedonthecamerastatus.

Example:SettingMANUALSHUTTERto1/10000S,settingwhentheSHUTTERMODEisAUTO.

=>Theproductwillonlyswitchto1/10000SwhentheSHUTTERMODEswitchestoMANUAL.



11．ADDRESS＆DATA(1stbyte＝05H，53H) ＊:donʼtcare

DataItem

Address H L Action

00H AUTO

01H MANU

MODE 01H ＊＊H

02H SS

SetstheSHUTTERMODEandEXTTRIGmode.

AUTO：Autoshutter

MANU：Manualmode

SS：Synchronousscanmode

LEVEL 03H ＊＊H 9CH

↓

00H

↓

64H

-100

↓

00

↓

100

Adjuststheautomaticshutterlevel.

LevelLow

↑Ifthehighlevelisselected,thevalueincreases.

↓Ifthelowlevelisselected,thevaluedecreases.

LevelHigh

PEAK/AVE 04H ＊＊H 00H

↓

0AH

00：10

↓

10：00

Adjuststheratiobetweenpeakandaveragevalueintheautomaticshuttermode.

00：Averageonly(01to09):Thebiggerthevalueis,thehighertheratiois.

10：Peakonly

SPEED 05H ＊＊H 00H

↓

13H

1

↓

20

Adjuststheautomaticshutterresponsespeed.

Thebiggerthevalueis,thefastertheresponseis.

00H PRESETA

01H PRESETB

02H PRESETC

03H PRESETD

AREA 06H ＊＊H

04H PRESETE

Selectstheavailablepictureareaintheautomaticshuttermode..

PRESETA,B,C,D,E:Specifiedrange

USER：Usersettingrange(Settingareaisavailable)

00H OFF

01H 1/100S

02H 1/125S

03H 1/250S

04H 1/500S

05H 1/1000S

06H 1/3000S

07H 1/5000S

08H 1/10000S

09H 1/30000S

MANUAL 0DH ＊＊H

0AH 1/50000S

Setsashutterspeedinmanualmode.

SHUTTER

SYNCHRO

SCAN 0EH 0001H

↓

0230H

001／1125H

↓

560／1125H

Setsashuttertimeeverytimeasynchronizationscanisturnedofforeveryhourof

datasetting.

001H/1125H〜560/1125H：Theshutterspeedcanbesetbythe1H.

(1H)(560H)

0231H OFF Shutterspeed1/60

Data

Item Address H L Action

00H AUTO

01H MANUAL

MODE 20H ＊＊H

02H OFF

Setsthemastergainmode.

AUTOMAX 21H ＊＊H 00H

↓

12H

00dB

↓

18dB

SetsthemaximumgainwhenthemastergainisAUTOmode.

GAIN

MANU 22H ＊＊H 00H

↓

12H

00dB

↓

18dB

Setsthegainwhenthemastergainismanual.

00H AWB

01H ATW

MODE 30H ＊＊H

02H MANUAL

Setsthewhitebalancemode.

00H 3200KC.TEMP 31H ＊＊H 01H 5600K Setsacolortemperature.

RPAINT 32H ＊＊H F6H

↓

00H

↓

0AH

-10

↓

00

↓

10

SetstheREDsettinginAWBmode.

BPAINT 33H ＊＊H F6H

↓

00H

↓

0AH

-10

↓

00

↓

10

SetstheBLUEsettinginAWBmode.

00H PRESETA

01H PRESETB

02H PRESETC

03H PRESETD

WHITE

BALANCE

AREA 34H ＊＊H

04H PRESETE

SetsinAWBmode.

PRESETA,B,C,D,E:inthespecifiedrange

Autres manuels pour IK-HD1

Ce manuel convient aux modèles suivants

Autres manuels Toshiba Caméra de sécurité

Toshiba

Toshiba IK-WR12A Manuel utilisateur

Toshiba

Toshiba IK-WB16A-W Manuel utilisateur

Toshiba

Toshiba IK-WB30A Manuel utilisateur

Toshiba

Toshiba IK-VR01A Manuel utilisateur

Toshiba

Toshiba IK-WB02A - PoE Network Camera Manuel utilisateur

Toshiba

Toshiba IK-WR01A Manuel utilisateur

Toshiba

Toshiba IK-HD1 Manuel utilisateur

Toshiba

Toshiba IK-WD14A Manuel utilisateur

Toshiba

Toshiba IK-WB21A - IP Network PTZ Camera Manuel utilisateur

Toshiba

Toshiba CS3330Bi Manuel utilisateur

Toshiba

Toshiba IK-WB01A Manuel utilisateur

Toshiba

Toshiba DF03A - IK CCTV Camera Manuel utilisateur

Toshiba

Toshiba WR01A - PoE Vandal Resistant Network Dome... Manuel utilisateur

Toshiba

Toshiba IK-WB11A Manuel d'utilisation et d'entretien

Toshiba

Toshiba IK-DF03A Manuel utilisateur

Toshiba

Toshiba IK-WB15A - IP Network Camera Instructions d'installation

Toshiba

Toshiba IK-TF5 Manuel utilisateur

Toshiba

Toshiba IK-527A Manuel utilisateur

Toshiba

Toshiba IK - TF1 Manuel utilisateur

Toshiba

Toshiba IK-DP01A Manuel utilisateur

Toshiba

Toshiba IK-WD05A Manuel utilisateur

Toshiba

Toshiba TQUICK START Manuel utilisateur

Toshiba

Toshiba 27A43 Manuel utilisateur

Toshiba

Toshiba IK-7100A Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur