Toshiba TE2000 Manuel utilisateur

TOSHIBA TE2000

Portable Personal Computer

User’s Manual

this manual cannot be reproduced in any form without the prior written permission

of TOSHIBA. No patent liability is assumed, with respect to the use of the informa-

tion contained herein.

TOSHIBA TE2000 Portable Personal Computer User’s Manual

First edition January 2002

Disclaimer

This manual has been validated and reviewed for accuracy. The instructions and

descriptions it contains are accurate for the TOSHIBA TE2000 Portable Personal

Computer at the time of this manual’s production. However, succeeding computers

and manuals are subject to change without notice. TOSHIBA assumes no liability

for damages incurred directly or indirectly from errors, omissions or discrepancies

between the computer and the manual.

Trademarks

IBM PC and PS/2 are trademarks of International Business Machines Corporation.

Intel and Pentium are registered trademarks, and Celeron and Intel SpeedStep are

trademarks of Intel Corporation.

Windows and Microsoft are registered trademarks of Microsoft Corporation.

Sound Blaster and Pro are trademarks of Creative Technology Ltd.

Photo CD is a trademark of Eastman Kodak.

Centronics is a registered trademark of Centronics Data Computer Corporation.

i.LINK is a trademark of Sony Corporation.

Other trademarks and registered trademarks not listed above may be used in this

manual.

EU Declaration of Conformity

TOSHIBA declares, that the product: PS600* conforms to the following Standards:

Supplementary Information: “The product complies with the requirements

of the Low Voltage Directive 73/23/EEC, the

EMC Directive 89/336/EEC and/or the

R&TTE Directive 1999/05/EEC.”

This product is carrying the CE-Mark in accordance with the related European

Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8,

41460 Neuss, Germany.

VCCI Class B Information

Modem warning notice

Conformity Statement

The equipment has been approved to [Commission Decision “CTR21”] for pan-

European single terminal connection to the Public Switched Telephone Network

(PSTN).

However, due to differences between the individual PSTNs provided in different

countries/regions the approval does not, of itself, give an unconditional assurance of

successful operation on every PSTN network termination point.

In the event of problems, you should contact your equipment supplier in the first

instance.

Network Compatibility Statement

This product is designed to work with, and is compatible with the following

networks. It has been tested to and found to conform with the additional require-

ments conditional in EG 201 121.

Germany ATAAB AN005,AN006,AN007,AN009,AN010 and

DE03,04,05,08,09,12,14,17

Greece ATAAB AN005,AN006 and GR01,02,03,04

Portugal ATAAB AN001,005,006,007,011 and P03,04,08,10

Spain ATAAB AN005,007,012, and ES01

Switzerland ATAAB AN002

All other countries/regions ATAAB AN003,004

Specific switch settings or software setup are required for each network, please refer

to the relevant sections of the user guide for more details.

The hookflash (timed break register recall) function is subject to separate national

type approvals. It has not been tested for conformity to national type regulations,

and no guarantee of successful operation of that specific function on specific

national networks can be given.

Japan regulations

Region selection

If you are using the computer in Japan, technical regulations described in the

Telecommunications Business Law require that you select the Japan region mode. It

is illegal to use the modem in Japan with any other selection.

Redial

Up to two redial attempts can be made. If more than two redial attempts are made,

the modem will return Black Listed. If you are experiencing problems with the

Black Listed code, set the interval between redials at one minute or longer.

Japan’s Telecommunications Business Law permits up to two redials on analogue

telephones, but the redials must be made within a total of three minutes.

The internal modem is approved by Japan Approvals Institute for Telecommunications

Equipment.

A00-0940JP

Pursuant to FCC CFR 47, Part 68:

When you are ready to install or use the modem, call your local telephone company

and give them the following information:

❑The telephone number of the line to which you will connect the modem

❑The registration number that is located on the device

The FCC registration number of the modem will be found on either the device

which is to be installed, or, if already installed, on the bottom of the computer

outside of the main system label.

❑The Ringer Equivalence Number (REN) of the modem, which can vary. For

the REN of your modem, refer to your modem’s label.

The modem connects to the telephone line by means of a standard jack called the

USOC RJ11C.

Type of service

Your modem is designed to be used on standard-device telephone lines. Connec-

tion to telephone company-provided coin service (central office implemented

systems) is prohibited. Connection to party lines service is subject to state tariffs. If

you have any questions about your telephone line, such as how many pieces of

equipment you can connect to it, the telephone company will provide this informa-

tion upon request.

Telephone company procedures

The goal of the telephone company is to provide you with the best service it can. In

order to do this, it may occasionally be necessary for them to make changes in their

equipment, operations, or procedures. If these changes might affect your service or

the operation of your equipment, the telephone company will give you notice in

writing to allow you to make any changes necessary to maintain uninterrupted

service.

If problems arise

If any of your telephone equipment is not operating properly, you should immedi-

ately remove it from your telephone line, as it may cause harm to the telephone

network. If the telephone company notes a problem, they may temporarily discon-

tinue service. When practical, they will notify you in advance of this disconnection.

If advance notice is not feasible, you will be notified as soon as possible. When you

are notified, you will be given the opportunity to correct the problem and informed

of your right to file a complaint with the FCC. In the event repairs are ever needed

on your modem, they should be performed by TOSHIBA Corporation or an

authorized representative of TOSHIBA Corporation.

Disconnection

If you should ever decide to permanently disconnect your modem from its present

line, please call the telephone company and let them know of this change.

Fax branding

The Telephone Consumer Protection Act of 1991 makes it unlawful for any person

to use a computer or other electronic device to send any message via a telephone

fax machine unless such message clearly contains in a margin at the top or bottom

of each transmitted page or on the first page of the transmission, the date and time it

is sent and an identification of the business, other entity or individual sending the

message and the telephone number of the sending machine or such business, other

entity or individual. In order to program this information into your fax modem, you

should complete the setup of your fax software before sending messages.

Instructions for IC CS-03 certified equipment

1The Industry Canada label identifies certified equipment. This certification

means that the equipment meets certain telecommunications network protective,

operational and safety requirements as prescribed in the appropriate Terminal

Equipment Technical Requirements document(s). The Department does not

guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be

connected to the facilities of the local telecommunications company. The

equipment must also be installed using an acceptable method of connection.

The customer should be aware that compliance with the above conditions may

not prevent degradation of service in some situations. Repairs to certified

equipment should be coordinated by a representative designated by the supplier.

Any repairs or alterations made by the user to this equipment, or equipment

malfunctions, may give the telecommunications company cause to request the

user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connec-

tions of the power utility, telephone lines and internal metallic water pipe system,

if present, are connected together. This precaution may be particularly important

in rural areas.

CAUTION: Users should not attempt to make such connections

themselves, but should contact the appropriate electric inspection

authority, or electrician, as appropriate.

2The user manual of analog equipment must contain the equipment’s Ringer

Equivalence Number (REN) and an explanation notice similar to the following:

The Ringer Equivalence Number (REN) of the modem, which can vary. For the

REN of your modem, refer to your modem’s label.

NOTICE: The Ringer Equivalence Number (REN) assigned to each

terminal device provides an indication of the maximum number of

terminals allowed to be connected to a telephone interface. The termina-

tion on an interface may consist of any combination of devices subject

only to the requirement that the sum of the Ringer Equivalence Numbers

of all the devices does not exceed 5.

3The standard connecting arrangement (telephone jack type) for this equipment is

jack type(s): USOC RJ11C.

The IC registration number of the modem is shown below.

Canada: 1353 11026A

Notes for Users in Australia and New Zealand

Modem warning notice for Australia

Modems connected to the Australian telecoms network must have a valid Austel

permit. This modem has been designed to specifically configure to ensure compli-

ance with Austel standards when the country/region selection is set to Australia. The

use of other country/region setting while the modem is attached to the Australian

PSTN would result in you modem being operated in a non-compliant manner. To

verify that the country/region is correctly set, enter the command ATI which

displays the currently active setting.

To set the country/region permanently to Australia, enter the following command

sequence:

AT%TE=1

ATS133=1

AT&F

AT&W

AT%TE=0

ATZ

Failure to set the modem to the Australia country/region setting as shown above will

result in the modem being operated in a non-compliant manner. Consequently, there

would be no permit in force for this equipment and the Telecoms Act 1991

prescribes a penalty of $12,000 for the connection of non-permitted equipment.

Notes for use of this device in New Zealand

❑The grant of a Telepermit for a device in no way indicates Telecom acceptance

of responsibility for the correct operation of that device under all operating

conditions. In particular the higher speeds at which this modem is capable of

operating depend on a specific network implementation which is only one of

many ways of delivering high quality voice telephony to customers. Failure to

operate should not be reported as a fault to Telecom.

❑In addition to satisfactory line conditions a modem can only work properly if:

a/ it is compatible with the modem at the other end of the call and

b/ the application using the modem is compatible with the application at the

other end of the call - e.g., accessing the Internet requires suitable software

in addition to a modem.

❑This equipment shall not be used in any manner which could constitute a

nuisance to other Telecom customers.

❑Some parameters required for compliance with Telecom’s PTC Specifications

are dependent on the equipment (PC) associated with this modem. The

associated equipment shall be set to operate within the following limits for

compliance with Telecom Specifications:

a/ There shall be no more than 10 call attempts to the same number within

any 30 minute period for any single manual call initiation, and

b/ The equipment shall go on-hook for a period of not less than 30 seconds

between the end of one attempt and the beginning of the next.

c/ Automatic calls to different numbers shall be not less than 5 seconds

apart.

❑Immediately disconnect this equipment should it become physically damaged,

and arrange for its disposal or repair.

❑The correct settings for use with this modem in New Zealand are as follows:

ATB0 (CCITT operation)

AT&G2 (1800 Hz guard tone)

AT&P1 (Decadic dialing make-break ratio =33%/67%)

ATS0=0 (not auto answer)

ATS10=less than 150 (loss of carrier to hangup delay, factory default of 15

recommended)

ATS11=90 (DTMF dialing on/off duration=90 ms)

ATX2 (Dial tone detect, but not (U.S.A.) call progress detect)

❑When used in the Auto Answer mode, the S0 register must be set with a value

of 3 or 4. This ensures:

(a) a person calling your modem will hear a short burst of ringing before the

modem answers. This confirms that the call has been successfully

switched through the network.

(b) caller identification information (which occurs between the first and

second ring cadences) is not destroyed.

❑The preferred method of dialing is to use DTMF tones (ATDT...) as this is

faster and more reliable than pulse (decadic) dialing. If for some reason you

must use decadic dialing, your communications program must be set up to

record numbers using the following translation table as this modem does not

implement the New Zealand “Reverse Dialing” standard.

Number to be dialed: 0 1 2 3 4 5 6 7 8 9

Number to program into computer: 0 9 8 7 6 5 4 3 2 1

Note that where DTMF dialing is used, the numbers should be entered

normally.

❑The transmit level from this device is set at a fixed level and because of this

there may be circumstances where the performance is less than optimal. Before

reporting such occurrences as faults, please check the line with a standard

Telepermitted telephone, and only report a fault if the phone performance is

impaired.

❑It is recommended that this equipment be disconnected from the Telecom line

during electrical storms.

❑When relocating the equipment, always disconnect the Telecom line connec-

tion before the power connection, and reconnect the power first.

❑This equipment may not be compatible with Telecom Distinctive Alert

cadences and services such as FaxAbility.

NOTE THAT FAULT CALLOUTS CAUSED BY ANY OF THE

ABOVE CAUSES MAY INCUR A CHARGE FROM TELECOM

General conditions

As required by PTC 100, please ensure that this office is advised of any changes to

the specifications of these products which might affect compliance with the relevant

PTC Specifications.

The grant of this Telepermit is specific to the above products with the marketing

description as stated on the Telepermit label artwork. The Telepermit may not be

assigned to other parties or other products without Telecom approval.

A Telepermit artwork for each device is included from which you may prepare any

number of Telepermit labels subject to the general instructions on format, size and

colour on the attached sheet.

The Telepermit label must be displayed on the product at all times as proof to

purchasers and service personnel that the product is able to be legitimately con-

nected to the Telecom network.

The Telepermit label may also be shown on the packaging of the product and in the

sales literature, as required in PTC 100.

The charge for a Telepermit assessment is $337.50. An additional charge of $337.

50 is payable where an assessment is based on reports against non-Telecom New

Zealand Specifications. $112.50 is charged for each variation when submitted at

the same time as the original.

An invoice for $NZ1237.50 will be sent under separate cover.

Autres manuels pour TE2000

Table des matières

Autres manuels Toshiba Ordinateur portable

Toshiba

Toshiba M750 - Portege - Core 2 Duo 2.53 GHz Manuel utilisateur

Toshiba

Toshiba L505D-ES5025 Manuel utilisateur

Toshiba

Toshiba 520 series Manuel utilisateur

Toshiba

Toshiba Satellite 2775XDVD Instructions d'installation

Toshiba

Toshiba Satellite Pro L70-B Series Manuel utilisateur

Toshiba

Toshiba R850-S8522 Manuel utilisateur

Toshiba

Toshiba A665-3DV7 Manuel utilisateur

Toshiba

Toshiba R850-Landis Manuel utilisateur

Toshiba

Toshiba R840-S8412 Manuel utilisateur

Toshiba

Toshiba A55-S326 Manuel utilisateur

Toshiba

Toshiba Tecra S4 Manuel utilisateur

Toshiba

Toshiba Portege R400 Series Manuel utilisateur

Toshiba

Toshiba Satellite A200 Series Manuel utilisateur

Toshiba

Toshiba L300-EZ1522 Manuel utilisateur

Toshiba

Toshiba Satellite P50W-B Series Manuel utilisateur

Toshiba

Toshiba L675D-S7107 Manuel utilisateur

Toshiba

Toshiba Satellite U200-ST3311 Series Manuel utilisateur

Toshiba

Toshiba Satellite M305-S4820 Manuel utilisateur

Toshiba

Toshiba P755-S5390 Manuel utilisateur

Toshiba

Toshiba Satellite C670 Manuel utilisateur

Toshiba

Toshiba Satellite M45-S169 Manuel utilisateur

Toshiba

Toshiba M10-S405 Manuel utilisateur

Toshiba

Toshiba L505D S5986 - Satellite - Athlon II 2 GHz Manuel utilisateur

Toshiba

Toshiba Satellite E105-S1802 Manuel utilisateur

Manuels Ordinateur portable populaires d'autres marques

HP ze2401xt - Pavilion Notebook PC Manuel utilisateur

Velocity

Velocity NoteMagix M10 Manuel utilisateur

Dell

Dell Alienware 17 R2 Manuel utilisateur

HP ENVY 17 Manuel

Winbook

Winbook LM Manuel utilisateur

Dell

Dell Inspiron 1464 Manuel utilisateur

Dell

Dell Inspiron 15R 5537 Manuel utilisateur

HP PROBOOK 4520S Manuel

Dell

Dell Latitude ATG D620 Manuel utilisateur

Sony

Sony VAIO PCG-FX270 Manuel utilisateur

Dell

Dell Latitude 7310 Manuel utilisateur

Dell

Dell Precision GU806 Manuel utilisateur

Sony

Sony VAIO PCG-R505JLK Manuel utilisateur

Lenovo

Lenovo THINKPAD X32 Manuel utilisateur

HP Compaq tc4200 Guide de démarrage rapide

Lenovo

Lenovo ThinkPad X201 Tablet Manuel

Lenovo

Lenovo THINKPAD X31 Manuel

Sony

Sony VGN-T240P VAIO Manuel utilisateur