Toshiba RD-XS35SU Manuel utilisateur
HDD/DVD VIDEO RECORDER
SERVICE MANUAL
Mar., 2006 GREEN
FILE NO. 810-200622GR
RD-XS35SU
RD-XS35SC
DIGITAL VIDEO
The above models are classified as green products (*1), as indicated by the underlined serial numbers.
This Service Manual describes replacement parts for the green products. When repairing these green
product(s), use the part(s) described in this manual and lead-free solder (*2).
For (*1) and (*2), see the next page.
(*1) GREEN PRODUCT PROCUREMENT
The EC is actively promoting the WEEE & RoHS Directives that define standards for recycling
and reuse of Waste Electrical and Electronic Equipment and for the Restriction of the use of
certain Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing
of new products containing the restricted substances.
Increasing attention is given to issues related to the global environmental.Toshiba Corporation
recognizes environmental protection as a key management tasks, and is doing its utmost to
enhance and improve the quality and scope of its environmental activities. In line with this,
Toshiba proactively promotes Green Procurement, and seeks to purchase and use products,
parts and materials that have low environmental impacts.
Green procurement of parts is not only confined to manufacture.The same green parts used in
manufacture must also be used as replacement parts.
(*2) LEAD-FREE SOLDER
This product is manufactured using lead-free solder as a part of a movement within the consumer
products industry at large to be environmentally responsible. Lead-free solder must be used in the
servicing and repair of this product.
WARNING
This product is manufactured using lead free solder.
DO NOT USE LEAD BASED SOLDER TO REPAIR THIS PRODUCT !
The melting temperature of lead-free solder is higher than that of leaded solder by 86°F to 104°F
(30°C to 40°C). Use of a soldering iron designed for lead-based solders to repair product made
with lead-free solder may result in damage to the component and or PCB being soldered. Great
care should be made to ensure high-quality soldering when servicing this product especially when
soldering large components, through-hole pins, and on PCBs as the level of heat required to melt
lead-free solder is high.
PREPARATION OF SERVICING
Pickup Head consists of a laser diode that is very susceptible to external static electricity.
Although it operates properly after replacement, if it was subject to electrostatic discharge during replacement, its
life might be shortened. When replacing, use a conductive mat, soldering iron with ground wire, etc. to protect the
laser diode from damage by static electricity.
And also, the LSI and IC are same as above.
1M
W
Ground conductive
wrist strap for body.
Soldering iron
with ground wire
or ceramic type
Conductive mat The ground resistance
between the ground line
and the ground is less than 10
W
.
LASER BEAM CAUTION LABEL
When the power supply is being turned on, you may not remove this laser cautions label. If it removes, radiation of a laser
may be received.
·Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
·“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
·Manufactured under license from QSound Labs, Inc. U.S. patent Nos. 5,105,462, 5,208,860 and 5,440,638 and various foreign counterpart. Copyright
QSound Labs, Inc. 1998-2002. QXpanderTM is a trademark of QSound Labs, Inc. All rights reserved.
·In the United States, TV GUIDE and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or of its affiliates. In
Canada, TV GUIDE is a registered mark of Transcontinental Inc., and is used under license by Gemstar-TV Guide International, Inc.
·The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its affiliates.
·The TV Guide On Screen system is protected by one or more of the following issued United States patents 6,498,895, 6,418,556, 6,331,877, 6,239,794;
6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121.
SAFETY NOTICE
SAFETY PRECAUTIONS
LEAKAGE CURRENT CHECK
Plug the AC line cord directly into a 120V AC outlet (do
not use an isolation transformer for this check). Use an
AC voltmeter, having 5000 Ωper volt or more sensitivity.
Connect a 1500 Ω10 W resistor, paralleled by a 0.15 µF
150V AC capacitor between a known good earth ground
(water pipe, conduit, etc.) and all exposed metal parts of
cabinet (antennas, handle bracket, metal cabinet
screwheads, metal overlays, control shafts, etc.).
Measure the AC voltage across the 1500 Ωresistor.
The test must be conducted with the AC switch on and
then repeated with the AC switch off. The AC voltage
indicated by the meter may not exceed 0.3 V. A reading
exceeding 0.3 V indicates that a dangerous potential
exists, the fault must be located and corrected.
Repeat the above test with the DVD VIDEO RECORDER
power plug reversed.
NEVER RETURN A DVD VIDEO RECORDER TO
THE CUSTOMER WITHOUT TAKING NECESSARY
CORRECTIVE ACTION.
READING SHOULD NOT EXCEED 0.3V
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
DVD VIDEO RECORDER AC VOLTMETER
(5000 Ωper volt
or more sensitivity)
Good earth ground
such as a water pipe,
conduit, etc.
1500 Ω
10 W
0.15 µF 150V AC
AC OUTLET
Test all exposed metal.
Voltmeter Hook-up for Leakage Current Check
SECTION 2
PART REPLACEMENT AND ADJUSTMENT PROCEDURES
SECTION 3
SERVICING DIAGRAMS
1. CIRCUIT SYMBOLS AND
SUPPLEMENTARY EXPLANATION
1-1. Precautions for Part Replacement
1-2. Solid Resistor Indication
1-3. Capacitance Indication
1-4. Inductor Indication
1-5. Waveform and Voltage Measurement
1-6. Others
2. PRINTED WIRING BOARD AND
SCHEMATIC DIAGRAM
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram
4. CIRCUIT DIAGRAMS
4-1. Power Supply Circuit Diagram
4-2. Front Circuit Diagram
4-2-1. Front Circuit Diagram (L/R)
4-2-2. Front Jack Circuit Diagram
4-3. Digital Circuit Diagram
4-3-1. Digital 1 Circuit Diagram
4-3-2. Digital 2 Circuit Diagram
4-4. Mother Circuit Diagram
4-4-1. Tuner Circuit Diagram
4-4-2. Audio Circuit Diagram
4-4-3. Timer Circuit Diagram
4-4-4. Video Circuit Diagram
4-5. Tuner Unit Circuit Diagram
5. PC BOARDS
5-1. Front Jack PC Board
5-2. Front (L) PC Board
5-3. Front (R) PC Board
5-4. Tuner Unit PC Board
5-5. Digital PC Board
5-6. Mother PC Board
CONTENTS
SECTION 1
GENERAL DESCRIPTIONS
1. OPERATING INSTRUCTIONS
1. REPLACEMENT OF MECHANICAL PARTS
1-1. Cabinet Replacement
1-1-1. Top Cover
1-1-2. HDD
1-1-3. Front Panel
1-1-4. RAM Dive
1-1-5. Rear Panel
1-1-6. Fan
1-2. PC Board Replacement
1-2-1. Tuner Unit PC Board
1-2-2. Digital PC Board
1-2-3. Mother PC Board
1-2-4. Power PC Board
1-2-5. Front (R), Front (L), and Front (Jack) PC Board
2. WIRING CONNECTION DIAGRAM
2. LOCATION OF MAIN PARTS
2-1. Location of Main Parts
2-2. Location of PC Boards
SECTION 4
PARTS LIST
SAFETY PRECAUTION
NOTICE
ABBREVIATIONS
1. Integrated Circuit (IC)
2. Capacitor (Cap)
3. Resistor (Res)
4. EXPLODED VIEWS
4-1. Packing Assembly
4-2. Chassis Assembly
5. PARTS LIST
SECTION 1
GENERAL DESCRIPTIONS
1. OPERATING INSTRUCTIONS
Please refer to the owner's manual about the contents.
SECTION 1
GENERAL DESCRIPTIONS
2. LOCATION OF MAIN PARTS
2-1. Location of Main Parts
Fig. 1-2-1
2-2. Location of PC Boards
Fig. 1-2-2
ZG45 FAN
RAM1 RAM DRIVE
HDD1 HDD UNIT
E
U05
Mother P
C
Boar
d
E
U0
2 Power P
C
Boar
d
EU01 Digital PC Board
Board
E
U8
2 Tuner
U
nit P
C
Boar
d
EU03A Front
(
R
)
PC Boar
d
EU03B Front (L)
F
PC Board
ar
EU55 Front
(
Jack
)
P
C
Boar
d
SECTION 2
PART REPLACEMENT AND
ADJUSTMENT PROCEDURES
SECTION 2
PART REPLACEMENT AND
ADJUSTMENT PROCEDURES
CAUTIONS BEFORE STARTING PART REPLACEMENT
Electronic parts are susceptible to static electricity and may easily damaged, so do not forget to ground as required.
Many screws are used inside the unit. To prevent the screws from missing or dropping, etc. always use a magnetized
screwdriver in servicing. Several kinds of screws are used and some of them need special cautions. That is, take care of
the tapping screws securing molded parts and fine pitch screws used to secure metal parts. If they are used improperly,
the screw holes will be easily damaged and the parts can not be fixed.
1. REPLACEMENT OF MECHANICAL PARTS
1-1. Cabinet Replacement
1-1-1. Top Cover
1. Remove seven screws (1), then remove the top cover (2).
Fig. 2-1-1
Screws (1)
Screws (1)
Screws (1)
Top cover (2)
1-1-2. HDD
1. Remove the top cover. (Refer to item 1-1-1.)
2. Remove two tapes (1).
3. Remove four screws (2).
4. Disconnect the flexible cable (3) and the connector (4).
5. Remove four screws (5), then remove the damper (7) and HDD (8) from the bracket (6).
Note:
• Attach the tapes (1) as they were after the HDD is replaced.
Fig. 2-1-2
Connector (4)
Screws (5)
Screws (5)
Bracket (6)
Damper (7)
HDD (8)
Flexible
cable (3)
Damper (7)
Screws (2)
Tape (1)
Tape (1)
Connector
Claw
Flexible
cable (3)
Damper (7)
Damper (7)
1-1-3. Front Panel
1. Remove the top cover. (Refer to item 1-1-1.)
2. Remove the tape (1).
3. Disconnect two connectors (2) and two flexible cables (3).
4. Remove two screws (4), four claws, then remove the front panel (5).
Note:
• Attach the tape (1) as it was after the front panel is replaced.
Fig. 2-1-3
Connector (2)
Connector (2)
Flexible cables (3)
Front panel (5)
Claws
Claw
Claw
Screws (4)
Tape (1)
Autres manuels pour RD-XS35SU
3
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Toshiba DVR
Toshiba
Toshiba DR430KU Manuel utilisateur
Toshiba
Toshiba D-KVR20KU Manuel utilisateur
Toshiba
Toshiba RD-KX50SU Manuel utilisateur
Toshiba
Toshiba D-KR4 Manuel utilisateur
Toshiba
Toshiba D-RW2 - DVD Recorder With TV Tuner Manuel utilisateur
Toshiba
Toshiba Symbio 160HD4 Manuel utilisateur
Toshiba
Toshiba NVSe Manuel utilisateur
Toshiba
Toshiba RD-85DTSB Manuel utilisateur
Toshiba
Toshiba SD-1600 Manuel utilisateur
Toshiba
Toshiba D-R1SU Manuel utilisateur
Toshiba
Toshiba NVR16-X Manuel utilisateur
Toshiba
Toshiba D-RW2SU Manuel utilisateur
Toshiba
Toshiba RD-XS24SG Manuel utilisateur
Toshiba
Toshiba D-R4SU Manuel utilisateur
Toshiba
Toshiba D-R420KU Manuel utilisateur
Toshiba
Toshiba RD-X2 Manuel utilisateur
Toshiba
Toshiba D-R550KU Manuel utilisateur
Toshiba
Toshiba D-VR41KF Manuel utilisateur
Toshiba
Toshiba SD46VSR Manuel utilisateur
Toshiba
Toshiba RD-XS32SB Manuel utilisateur
