Toshiba 2060 Comment utiliser

SERVICE HANDBOOK

PLAIN PAPER COPIER

2060/2860/70

Click the Page Only button to close the overview area of the window.

Click the Bookmarks and Page button to open the Contents and

display bookmarks created for the document. Click a bookmark’s name

to go to the Page marked by that bookmark.

Click the Thumbnails and Page button to open the overview area and

display thumbnail images of each document page. Click a thumbnail to

go to the page marked by that thumbnail.

AUTOMATIC DUPLEXING UNIT

MD-5002

GENERAL PRECAUTIONS REGARDINGTHE INSTALLATION

AND SERVICE FOR THE COPIER 2060, 2860/70 AND THE AU-

TOMATIC DUPLEXING UNIT MD-5002

1. Transportation/Installation

• When transporting/installing the copier, use two persons and be sure to use the positions as indi-

cated below.

The copier is fairly heavy and weighs approximately 73 kg (161 lb), therefore pay full attention

when handling it. (2870: 84 kg)

4 portions

2. Installation

• Be sure to use a dedicated outlet with AC 115V/15A (220V, 240V/10A) or more for its power

source.

• The copier must be grounded for safety.

Never ground it to a gas pipe or a water pipe.

• Select a suitable place for installation.

Avoid excessive heat, high humidity, dust, vibration and direct sunlight.

• Also provide proper ventilation as the copier emits a slight amount of ozone.

• To insure adequate working space for the copying operation, keep a minimum clearance of 80 cm

(32”) on the left, 80 cm (32”) on the right and 10 cm (4”) in the rear.

3. Service of Machines

• Basically, be sure to turn the main switch off and unplug the power cord during service.

• Be sure not to touch high-temperature sections such as the exposure lamp, the fuser unit, the

damp heater and their periphery.

• Be sure not to touch high-voltage sections such as the chargers and the high-voltage transformer.

• Be sure not to touch rotating/operating sections such as gears, belts, pulleys, etc.

• When servicing the machines with the main switch turned on, be sure not to touch live sections

such as the lamp terminal, etc.

• Use suitable measuring instruments and tools.

4. Main Service Parts for Safety

• The breaker, door switch, fuse, thermostat, thermofuse, thermistor, etc. are particularly important

for safety. Be sure to handle/install them properly.

5. Notice Labels

• Be sure to check the rating plate and the cautionary labels such as “Unplug the power cord during

service”, “Hot area” etc. to see if there is any dirt on their surface or if they are properly stuck to the

copier during servicing.

6. Disposition of Consumable Parts/Packing Materials

• Regarding the recovery and disposal of the copier, supplies, consumable parts and packing mate-

rials, it is recommended to follow the relevant local regulations or rules.

7. When parts are disassembled, reassembly is basically the reverse of disassembly unless

otherwise noted in this manual or other related documents. Be careful not to reassemble

small parts such as screws, washers, pins, E-rings, toothed washers in the wrong places.

8. Basically, the machine should not be operated with any parts removed or disassembled.

9. Precautions Against Static Electricity

• The PC board must be stored in an anti-electrostatic bag and handled carefully using a wristband,

because the ICs on it may become damaged due to static electricity.

Dec. 1996 © TOSHIBA CORP. 1 - 1 2060, 2860/70 ADJUSTMENT

1. ADJUSTMENT ITEMS

1.1 Error Codes

WheneithertheCLEARPAPER ( ) orCALL SERVICE( ) symbol appears,press theCLEAR/

STOP and “8” keys simultaneously and the corresponding error code will be displayed. To clear the

error code, turn off the machine.

Group

Error code

Machine status

Transporting jam at the copier

Paper feeding jam

Paper transporting jam at the

feeding units

Original transporting jam at the

ADF

Paper transporting jam at the

sorter

Service call by the drive system

Paper jam inside the copier

Paper jam near the fuser unit

Paper remaining inside the machine when power on

The front cover is opened during copying

Paper jam near the aligning roller

Paper jam at the stacking area inside the ADU

Paper feeding jam at the ADU

Manual feeding jam

Cassette feeding or transporting jam (1st cassette)

Cassette feeding or transporting jam (2nd cassette)

Cassette feeding or transporting jam (3rd cassette)

Cassette feeding or transporting jam (4th cassette)

Cassette feeding or transporting jam (5th cassette)

Paper feeding or transporting jam at the LCF

Paper jam at the transport route 1 (LCF)

Paper jam at the transport route 2 (Copier)

Paper jam at the transport route 3 (Aligning)

Paper jam at the transport route 4 (PFP)

Original feeding jam

Original transporting jam

Original exiting jam

2nd original feeding jam (2 in 1)

Copy paper arrival time is over

Copy paper staying time is over

Sorter early arrival jam

Paper remaining inside the sorter when power on

Joint open jam while copying

Staple jam

Abnormal operation of the copier main motor

Abnormal operation of the PFP main motor

Abnormal operation of the ADU main motor

E01

E02

E03

E04

E05

E08

E11

E12

E13

E14

E15

E16

E17

E19

E21

E22

E23

E25

E71

E72

E73

E75

E81

E82

E83

E84

E85

E88

C01

C04

C05

2060, 2860/70 ADJUSTMENT 1 - 2 Dec. 1996 © TOSHIBA CORP.

Group

Error code

Machine status

Service call by the paper feeding

system

Service call by the optical system

Service call by the process system

Fuser unit area

Service call by communication

Service call by ADF

Service call by sorter

Service call by the other

C11

C12

C13

C14

C15

C16

C17

C18

C21

C22

C23

C26

C33

C35

C41

C43

C44

C45

C54

C55

C56

C72

C73

C74

C81

C82

C83

C84

C85

C86

C87

C88

C93

Abnormal operation of the ADU side motor

Abnormal operation of the ADU end motor

Abnormal operation of the upper cassette tray

Abnormal operation of the lower cassette tray

Abnormal operation of the PFP upper cassette tray

Abnormal operation of the PFP middle cassette tray

Abnormal operation of the PFP lower cassette tray

Abnormal operation of the LCF tray

Carriage initialize error

Lens initialize error

Mirror initialize error

Exposure lamp burn out detected

Easy set-up is failed

Developer material exist at the transfer/separation adjustment

Abnormal thermistor or heater disconnection when power is on

Warming up mode after disconnection judgement, or abnor-

mal thermistor after ready

Warming up mode after disconnection judgement, or heater

disconnection after ready

Sub thermistor is open-circuited

Sorter — Main CPU communication error

ADF — Main CPU communication error

PFC — Main CPU communication error

Poor adjustment by the aligning sensor detected

EEROM poor initialized

Poor adjustment by the exit/reserve sensor detected

Paper transport motor abnormal

Bin shifting motor abnormal

Upper limit error

Lower limit error

Home sensor error

Staple guide bar drive motor abnormal

Staple drive motor abnormal

Copy removal sensor error

ADF original stop signal not received

Note: If there is a possibility of the heater malfunctioning as a consequence of the short-circuiting of the triac, the

microcomputer will check for abnormal temperature and send out error code “C44” and turn off the main

switch of the copier.

Dec. 1996 © TOSHIBA CORP. 1 - 3 2060, 2860/70 ADJUSTMENT

1.2 Self-Diagnosis Modes

Mode Input Definition Cleaning Display after selection

code method

All-LEDs-lit

Aging mode

Test mode

Adjustment

mode

Forced ready

mode

Aging mode

Setting mode

“01”

“02”

“03”

“04”

“05”

“06”

“07”

“08”

All LEDs on the control panel are lit.

Aging (RADF does not operate)

Motor test and input/output check

Adjustment of items

Forced entry of ready mode

Aging (includes RADF)

System switch over and setting of each

priority mode, PM counter, etc.

C/S

“09”

–

“09”

AGING 100%

TEST MODE 100%

AGING 100%

TEST MODE 100%

Note: To access the desired diagnostic mode, turn on the power switch while pressing the appropriate keys.

• All-LEDs-lit mode (01):

• Aging mode (02 or 07):

• Test mode (03 or 04):

For these test modes, refer to 1.2.1 and 1.2.2.

• Adjustment mode (05):

For this mode, refer to “1.2.3 Adjustment mode”.

• Forced ready mode (06):

Note: This mode is for checking the paper feeding operation only.

• Setting mode (08):

For this mode, refer to “1.2.4 Setting mode”.

Notes: C/S: Press the CLEAR/STOP key

PWR: Turn on the power switch

INT: Press the INTERRUPT key

E/S: Press the ENERGY SAVER key

0 1 C/S

0 2 0 9

0 7

C/S

0 6

All LEDs light

Aging

PWR Exit

Exit

PWR

PWR Forced ready

2060, 2860/70 ADJUSTMENT 1 - 4 Dec. 1996 © TOSHIBA CORP.

Quick reference chart for self-diagnostic mode

Normal

“09” “09”

* “P”: PRINT key on.

“C”: CLEAR/STOP key on.

Warming up

Standby

“06”

“C”

“01”

*2 “02”

All the displays on

the control panel lit Aging

“07”

(With ADF)

“P” “C”

Stops momentarily

“09”

“03/04” “05” “08”

“05”

“09”

Setting mode

Adjustment mode

Test mode

*1 When the copier is in the adjustment mode which you entered by turning on the power switch while

pressing keys “0” and “5” simultaneously, pressing keys “0” and “9” simultaneously will make the

copier exit into the stand-by mode. In this stand-by mode only, you can access the adjustment

mode repeatedly by simply entering “0” and “5”.

*2 While all the displays on the control panel are lit (“01” mode), copying is disenabled.

When the copier enters the standby status by pressing the CLEAR/STOP key, copying is enabled.

Power ON

Dec. 1996 © TOSHIBA CORP. 1 - 5 2060, 2860/70 ADJUSTMENT

1.2.1 Input signal check (Test mode 03/04)

In the “03” or “04” test mode, the following input signal conditions can be checked by pressing the

appropriate keys.

[A] When automatic exposure is selected

A4/LD

A3/LG

B4/LT

A5/ST

UNIVERSAL/OTHER

ORGINAL COPY

PLTNSW

Closed

–

HOMESW

Carriage

home position

–

PLL-OK

Main motor

rotation NG

–

MRRSW

Mirror home

position

–

HTRDY

Heater

Size width

sensor 2

Copy removal

sensor

PSTPSW

Paper found

PCCNT

SCNT

Sorter

not loaded

–

Empty

sensor

Bin home

sensor

–

APSR

Rear sensor not

found original

DEVSW

Dev unit

not loaded

APS2

Original

not found

Open

sensor

One rotation

detect sensor

–

APSC

Center sensor not

found original

TFULSW

Not toner

full

APS1

Original

not found

Exit

sensor

Tray paper

detect sensor

–

APSF

Front sensor not

found original

–

APS0

Original

not found

Aligning

sensor

Entrance

sensor

Original size LED Copy size LED

A4/LD A3/LG B4/LT A5/ST A4/LD A3/LG B4/LT A5/ST

[1] Key

[2] Key

[3] Key

[4] Key

[5] Key

[6] Key

Sorter

Copier

Unit

ADF

Indicator

LED

Key

operation

LED lit in above condition (Signal level : H)

LNZSW

Lens home

position

EXITSW

Paper found

DFCNT

not loaded

–

Size width

sensor 1

Limit

sensor

2060, 2860/70 ADJUSTMENT 1 - 6 Dec. 1996 © TOSHIBA CORP.

[B] When manual exposure is selected

A4/LD

A3/LG

B4/LT

A5/ST

UNIVERSAL/OTHER

ORGINAL COPY

UCVDOR

U-turn cover

opened

LCDOR

LCF

door opened

–

ENDSW

ADU end

guide home

SW ON

SIZCL3

Copier

lower cassette

SIZE SW OFF

SIZPF23

Pedestal

middle cassette

SIZE SW OFF

–

TUPCU

Copier

lower cassette

tray top position

TDWNLC

LCF tray

bottom SW ON

TUPPF1

Pedestal

upper cassette

tray top position

TUPPF3

Pedestal

lower cassette

tray top position

PJAM1AD

ADU JAM SW

Paper present

SIZCL2

Copier

lower cassette

SIZE SW OFF

SIZPF22

Pedestal

middle cassette

SIZE SW OFF

–

PEMPCU

Copier

lower cassette

paper empty

TUPLC

LCF tray

top SW ON

PEMPPF1

Pedestal

upper cassette

paper empty

PEMPPF3

Pedestal

lower cassette

paper empty

–

SIZCL1

Copier

lower cassette

SIZE SW OFF

SIZPF21

Pedestal

middle cassette

SIZE SW OFF

–

PSTPCU

Copier

lower cassette

PSTP-SW ON

PEMPLC

LCF

paper empty

PSTPPF1

Pedestal

upper cassette

PSTP-SW ON

PSTPPF3

Pedestal

lower cassette

PSTP-SW ON

PEMPAD

ADU inside

Paper present

SIZCL0

Copier

lower cassette

SIZE SW OFF

SIZPF20

Pedestal

middle cassette

SIZE SW OFF

–

TUPCL

Copier

upper cassette

tray top position

–

TUPPF2

Pedestal

middle cassette

tray top position

PPLL-OK

Pedestal motor

rotating NG

AD-CNT

ADU not

installed

SIZCU2

Copier

upper cassette

SIZE SW OFF

SIZPF32

Pedestal

upper cassette

SIZE SW OFF

SIZPF12

Pedestal

lower cassette

SIZE SW OFF

PSTPCL

Copier

upper cassette

PSTP-SW ON

LC-CNT

LCF not

installed

PSTPPF2

Pedestal

middle cassette

PSTP-SW ON

PFDOR

PFP side

door opened

SIDSW

ADU side

guide home

SW ON

SIZCU0

Copier

upper cassette

SIZE SW OFF

SIZPF30

Pedestal

upper cassette

SIZE SW OFF

SIZPF10

Pedestal

lower cassette

SIZE SW OFF

Indicator

LED

Key

operation

–

SBFSW

Manual feed

paper empty

–

SIZCU3

Copier

upper cassette

SIZE SW OFF

SIZPF33

Pedestal

upper cassette

SIZE SW OFF

SIZPF13

Pedestal

lower cassette

SIZE SW OFF

PEMPCL

Copier

upper cassette

paper empty

LC-KEY

LCF tray

down key OFF

PEMPPF2

Pedestal

middle cassette

paper empty

PF-CNT

Pedestal

not installed

APLL-OK

ADU motor

rotating NG

SIZCU1

Copier

upper cassette

SIZE SW OFF

SIZPF31

Pedestal

upper cassette

SIZE SW OFF

SIZPF11

Pedestal

lower cassette

SIZE SW OFF

Unit

PFP

ADU

PFP

Copier

LED lit in above condition (Signal level : H)

Copier

LCF

Original size LED Copy size LED

A4/LD A3/LG B4/LT A5/ST A4/LD A3/LG B4/LT A5/ST

[1] Key

[2] Key

[3] Key

[4] Key

[5] Key

[6] Key

[7] Key

[8] Key

Note: 03 →With initialization before test mode is entered

04 →Without initialization

PWR PRINT Digital key LED ON (To clear)

0 3 0 9

AUTO-EXP

EXP

Autres manuels pour 2060

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Toshiba Photocopieuse

Toshiba

Toshiba 8070 Manuel utilisateur

Toshiba

Toshiba e-Studio 223CS Guide d'installation

Toshiba

Toshiba e-STUDIO 55 Manuel utilisateur

Toshiba

Toshiba 2460 Comment utiliser

Toshiba

Toshiba 1550 Comment utiliser

Toshiba

Toshiba e-STUDIO 550 Manuel utilisateur

Toshiba

Toshiba e-STUDIO203S Manuel utilisateur

Toshiba

Toshiba e-studio550 Manuel utilisateur

Toshiba

Toshiba 60th Series Manuel utilisateur

Toshiba

Toshiba MY-1015 Manuel utilisateur

Toshiba

Toshiba GA-1040 Manuel utilisateur

Toshiba

Toshiba 4550 Manuel utilisateur

Toshiba

Toshiba GA-1120 Manuel utilisateur

Toshiba

Toshiba e-studio120 Manuel utilisateur

Toshiba

Toshiba 1360 Manuel utilisateur

Toshiba

Toshiba e-STUDIO 55 Manuel utilisateur

Toshiba

Toshiba 3560 Comment utiliser

Toshiba

Toshiba e-studio 210c Manuel utilisateur

Toshiba

Toshiba FC15 Manuel utilisateur

Toshiba

Toshiba e-studio 120 Manuel utilisateur

Toshiba

Toshiba 2550 Manuel utilisateur

Toshiba

Toshiba MR-2017 Manuel utilisateur

Toshiba

Toshiba 65/5560 Comment utiliser

Toshiba

Toshiba SmartLink e-STUDIO16 Manuel d'utilisation et d'entretien

Manuels Photocopieuse populaires d'autres marques

Canon

Canon iR1210 Manuel de référence

Ricoh

Ricoh FW740 Manuel utilisateur

Minolta

Minolta CF910 Manuel utilisateur

Ricoh

Ricoh B003 Manuel utilisateur

Xerox

Xerox EC70 Manuel utilisateur

Oce

Oce 9800 Manuel utilisateur

Olivetti

Olivetti d-Copia 1800 Manuel utilisateur

Minolta

Minolta Di181 Manuel utilisateur

Canon

Canon iR5000i Manuel utilisateur

Telecrane

Telecrane F25 Manuel utilisateur

Xerox

Xerox WorkCentre Pro 40 Manuel utilisateur

Canon

Canon NP6317 Comment utiliser

Sharp

Sharp AR-5015 N Manuel utilisateur

Ricoh

Ricoh Di-C1 Manuel utilisateur

Mita

Mita MIP-2400 Manuel

Sharp

Sharp AL-2061 Manuel utilisateur

Muratec

Muratec MFX-C2280 Manuel utilisateur

Ricoh

Ricoh FT5034C Manuel utilisateur