Toshiba E-STUDIO900 Guide d'installation

TECHNICAL TRAINING

PROGRAM

- PRE-STUDY MANUAL -

e-STUDIO900/1050

Toshiba America Business Solutions

It is the reader's responsibility when discussing the information contained within this

document to maintain a level of confidentiality that'sin the best interest of Toshiba

Corporation and its member companies.

NO PART OF THIS DOCUMENT MAY BE REPRODUCED IN ANY

FASHION AND DISTRIBUTED WITHOUT THE PRIOR

PERMISSION OF TOSHIBA CORPORATION.

ll product names, domain names or product illustrations, including desktop images, used in this

document are trademarks, registered trademarks or the property of their respective companies.

They are used throughout this book in an informational or editorial fashion only and for the benefit o

such companies. No such use, or the use of any trade name, or web site is intended to convey

endorsement or other affiliation with Toshiba products.

The Pre-Training Manual contains information

regarding service techniques, procedures, processe

and spare parts of office equipment distributed b

Toshiba Corporation. Users of this manual should be

either service trained or certified by successfull

completing a Toshiba Technical Training Program.

Untrained and uncertified users utilizing information

contained in this pre-training manual to repair or modif

Toshiba equipment risk personal injury, damage to

roperty or loss of warranty protection.

Toshiba Corporation

WARNING

LEGEND

PRODUCT CODE COMPANY

Toshiba

B070 900

B071 1050

LCT B511 MP-4501L(RT46 Large Capacity Tray)

Finisher B478 MJ-1026(SR840 3,000-SHEET FINISHER)

Cover Int. B470 MJ-7002(Cover Interposer Tray Type 1075)

Bypass Tray B512 MY-1024(Multi Bypass Tray Type 2105)

INTRODUCTION

The Pre-Training Manual for the 900/1050 has been designed to give the Service

Technician an overview of these products prior to attending the training program. This

manual starts with the basic fundamentals utilized in the machine and reviews the entire

copy process and accessories.

It is the aim of the Service Education and Development Division to give the Service

Technician as much hands-on experience as possible while attending training. In order to

accomplish this, a relatively small amount of time will be spent on the basic fundamentals

in class. For these reasons a thorough understanding of this document is necessary.

At the end of this Pre-Training Manual it is necessary to complete a Pre-Training Test

found on the Toshiba FYI Website.

This test is provided to ensure that the Service Technician has an understanding

of the electronics, the copy process and the machine operations. When this pre training

been completed and passed the technician is approved for the 5-day classroom course.

Should you have any questions, please contact the Service Training

Division.

Service Manager gives Technician

Pre-Training Manual. (download)

Technician completes pre-training.

Once completing the training, the

student completes the on-line exam.

After the exam is passed the student

receives immediate results.

Service manager receives results.

Student reviews the material and

does further preparation.

Technician is scheduled for school.

Student attends instructor led 5-day

training program.

FLOWCHART FOR PRE-TRAINING MANUAL

The Service Manager enrolls technican

for the class and pre-requisite exam.

This is done on-line at the FYI website.

The technician reviewsthe pre training

material.

CONTENTS

SECTION 1

OVERALL INFORMATION

SECTION 2

DETAILED DESCRIPTIONS

SECTION 3

SERVICE TABLES

SECTION 4

INSTALLATION

SECTION 5

LARGE CAPACITY TRAY

SECTION 6

SR860 BOOKLET FINISHER

with PUNCH UNIT

SECTION 7

SR840 3,000-SHEET FINISHER

with PUNCH UNIT

SECTION 8

COVER INTERPOSER TRAY TYPE 1075

SECTION 9

MULTI BYPASS TRAY TYPE 2105

IMPORTANT SAFETY NOTICES

PREVENTION OF PHYSICAL INJURY

1. Before disassembling or assembling parts of the copier and peripherals,

make sure that the copier power cord is unplugged.

2. The wall outlet should be near the copier and easily accessible.

3. Note that some components of the copier and the paper tray unit are

supplied with electrical voltage even if the main power switch is turned off.

4. If any adjustment or operation check has to be made with exterior covers off

or open while the main switch is turned on, keep hands away from electrified

or mechanically driven components.

5. If the Start key is pressed before the copier completes the warm-up period

(the Start key starts blinking red and green alternatively), keep hands away

from the mechanical and the electrical components as the copier starts

making copies as soon as the warm-up period is completed.

6. The inside and the metal parts of the fusing unit become extremely hot while

the copier is operating. Be careful to avoid touching those components with

your bare hands.

HEALTH SAFETY CONDITIONS

1. Never operate the copier without the ozone filters installed.

2. Always replace the ozone filters with the specified ones at the specified

intervals.

3. Toner and developer are non-toxic, but if you get either of them in your eyes

by accident, it may cause temporary eye discomfort. Try to remove with eye

drops or flush with cold water as first aid. If unsuccessful, get medical

attention.

OBSERVANCE OF ELECTRICAL SAFETY STANDARDS

1. The copier and its peripherals must be installed and maintained by a

customer service representative who has completed the training course on

those models.

2. The NVRAM on the controller board has a lithium battery which can explode

if replaced incorrectly. Replace the NVRAM only with an identical type.

However, the manufacturer recommends replacing the entire NVRAM, not

just the battery. Never recharge or incinerate a used NVRAM battery.

Dispose of a used NVRAM or NVRAM battery in accordance with local

regulations.

3. The danger of explosion exists if the battery on the controller board is

incorrectly replaced. Replace the battery only with the equivalent type

recommended by the manufacturer. Discard the used controller board

battery in accordance with the manufacturer’s instructions and local

regulations.

SAFETY AND ECOLOGICAL NOTES FOR DISPOSAL

1. Do not incinerate toner bottles or used toner. Toner dust may ignite suddenly

when exposed to an open flame.

2. Dispose of used toner, developer, and organic photoconductors in

accordance with local regulations. (These are non-toxic supplies.)

3. Dispose of replaced parts in accordance with local regulations.

4. When keeping used lithium batteries in order to dispose of them later, do not

put more than 100 batteries per sealed box. Storing larger numbers or not

sealing them apart may lead to chemical reactions and heat build-up.

LASER SAFETY

The Center for Devices and Radiological Health (CDRH) prohibits the repair of laser-

based optical units in the field. The optical housing unit can only be repaired in a factory or

at a location with the requisite equipment. The laser subsystem is replaceable in the field

by a qualified Customer Engineer. The laser chassis is not repairable in the field.

Customer engineers are therefore directed to return all chassis and laser subsystems to

the factory or service depot when replacement of the optical subsystem is required.

WARNING

Use of controls, or adjustment, or performance of procedures other than

those specified in this manual may result in hazardous radiation exposure.

WARNING

WARNING: Turn off the main switch before attempting any of the

procedures in the Laser Unit section. Laser beams can

seriously damage your eyes.

CAUTION MARKING:

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Toshiba Imprimante tout-en-un

Toshiba

Toshiba e-studio 2000ac Instructions originales

Toshiba

Toshiba e-studio202L Manuel utilisateur

Toshiba

Toshiba e-Studio 350 Manuel utilisateur

Toshiba

Toshiba e-BRIDGE Re-Rite Manuel utilisateur

Toshiba

Toshiba e-Studio 350 Manuel utilisateur

Toshiba

Toshiba E-STUDIO2000AC Manuel utilisateur

Toshiba

Toshiba e-STUDIO352 Instructions d'installation et d'entretien

Toshiba

Toshiba e-STUDIO2500c Manuel utilisateur

Toshiba

Toshiba E-STUDIO E-Studio 3511 Manuel utilisateur

Toshiba

Toshiba E-STUDIO 5518A Manuel utilisateur

Toshiba

Toshiba e-STUDIO161 Manuel utilisateur

Toshiba

Toshiba E-studio5540c Manuel utilisateur

Toshiba

Toshiba GA-1190 Manuel utilisateur

Toshiba

Toshiba E-STUDIO202S Guide de configuration

Toshiba

Toshiba e-studio 2006 Manuel utilisateur

Toshiba

Toshiba e-STUDIO GL-1010 Manuel

Toshiba

Toshiba e-studio 151 Manuel utilisateur

Toshiba

Toshiba GD-1370 Instructions d'installation et d'entretien

Toshiba

Toshiba e-STUDIO355 Manuel utilisateur

Toshiba

Toshiba e-STUDIO330AC Manuel utilisateur

Toshiba

Toshiba E-studio 281c Manuel utilisateur

Toshiba

Toshiba GA-1191 Manuel utilisateur

Toshiba

Toshiba e-STUDIO 600 Manuel utilisateur

Toshiba

Toshiba e-STUDIO 600 Manuel utilisateur

Manuels Imprimante tout-en-un populaires d'autres marques

Triumph Adler

Triumph Adler DC 2016 Manuel

Epson

Epson WorkForce WF-2510 Guide de l'utilisateur

Epson

Epson Stylus Scan 2000 Manuel d'installation et d'exploitation

Epson

Epson PictureMate Snap PM 240 Mode d’emploi

Konica Minolta

Konica Minolta bizhub C35 Manuel utilisateur

Brother

Brother MFC-J430w Manuel utilisateur

Konica Minolta

Konica Minolta BIZHUB 558 Manuel utilisateur

Lexmark

Lexmark MX710 Series Manuel

Brother

Brother MFC-9760 Manuel utilisateur

Lexmark

Lexmark XC8155 Manuel utilisateur

Lexmark

Lexmark X642E Manuel utilisateur

Sharp

Sharp MX-2310U Mode d’emploi

Aficio

Aficio 200 Manuel utilisateur

Canon

Canon ImageCLASS 2300 Manuel

Ricoh

Ricoh Pro C900 Manuel utilisateur

Lexmark

Lexmark X925 Manuel utilisateur

Brother

Brother Business Smart MFC-J4510dw Manuel utilisateur

Epson

Epson Stylus CX8400 Series Manuel utilisateur