TORP TC1000 Manuel utilisateur
TORP TC1000
CONTROLLER.
User Manual for Surron Light Bee
IMPORTANT.
Please read and carefully follow the instructions in this manual. The TC1000 controller must always
be used with a stock SurRon/Segway circuit breaker (fuse)! Not using the circuit breaker with the
TC1000 controller is dangerous and can cause serious damage!
Use only tools and screws that came with the controller. Using the tools and screws that were not
included in the parcel, not following these instructions, or not using the circuit breaker, can cause
serious damage to you and your bike.
INTRODUCTION.
TC1000 controller is compatible with:
-SurRon Light Bee/Segway X260
-Torp Motor TM25
-SurRon Ultra Bee.
TC1000 is not compatible with Segway X160. TC1000 controller is also not compatible with motor
model number P/N: 11100-YQ2A-0100. Please check your motor model number before installing
the TC1000 controller. In general, all SurRon/Segway X260 motors, manufactured after 2018 are
compatible with the TC1000 controller.
TC1000 controller is compatible with both versions of the stock display (L1 E & the off-road version).
Both speed and the distance are displayed on it. For the additional options, like battery monitoring
and settings, you will have to use your smartphone or buy a Torp Display, that is sold separately.
This is a plug&play controller that needs no previous knowledge of electronics and programming for
installation and setup. Everything needed for successful installation is included in the box.
WWW.TORPMOTORS.COM
1
2
THE BOX CONSIST OF:
- TC1000 controller
- Wiring harness
- 5 phase screws with washers
- 2 hex keys and 4 bolts
- 4 stickers
- Heat sink
- Short instructions
All the settings and diagnostics are managed through an
intuitive and easy-to use smartphone app for Android and
IOS. The users can use their smart-phone as a display
during the rides and to set up all the controller`s features
through the app.
WWW.TORPMOTORS.COM
WWW.TORPMOTORS.COM
INSTALLATION.
Before starting with the installation, drain the bike`s capacitors.
Switch off the fuse1.
Switch on the bike and wait for the capacitors to drain. 2.
1.
3
2.
Now you can start removing the stock SurRon controller and the battery from the frame, and lower
the skid-plate that covers the wiring.
USE THESE HOLES TO MOUNT
THE CONTROLLER ON THE BIKE.
STEP 1:
Place the controller in a way that the holes on its back align
with the upper holes on the bottom front of the frame.
STEP 2:
Insert each screw in one hole and fasten them by using a
smaller hex key.
1.
2.
USE SMALLER BOLTS TO FASTEN
THE CONTROLLER TO THE BIKE.
DON`T MESS THIS ONE UP!
STEP 5:
Connect the power and phase motor wires as shown on
the picture using the screws with washers that you have
removed from the controller in the previous step:
Power Wires:
-The red battery wire to the positive (+) electrode
-The black battery wire to the negative (-) electrode
Phase Motor Wires:
-The Blue motor wire to the letter B
-The Green motor wire to the letter G
-The Yellow motor wire to the letter Y
WWW.TORPMOTORS.COM
4
STEP 3:
There are 5 screws with washers already on the
controller. Remove them from the controller and
start connecting the controller to the phase
motor wires.
STEP 6:
Use a larger hex key to gently fasten the
screws with washers. Max Torque that should
be used is 3.5 Nm!
3.
5.
6.
5
WWW.TORPMOTORS.COM
STEP 7:
Use the wire harness that came with the
controller to connect the controller to the
bike. Connect the largest connector to the
controller and the three smaller connectors to
the bike`s wiring, in the same way the stock
controller has been connected.
There are also 2 more connectors with a cap
on it. To which the Torp Display and Thumb
throttle are connected. See page 20.
7.
WWW.TORPMOTORS.COM
6
9.
STEP 9:
Use the longer M6 screws
and a larger hex key to
fasten the shield to the frame.
8.
STEP 8:
Take the plastic shield that came with the
controller and mount it by placing its lower
part into the skid plate.
A USEFUL TIP.
Apply silicone grease to
the controller and the
main connector for
additional protection
from dirt and moisture.
WWW.TORPMOTORS.COM
7
STEP 12:
Turn the fuse back on. Always use the
Controller with the stock SurRon/Segway
fuse!
12.
STEP 11:
Connect the battery to the battery power
connector and to the 6-pin connector.
11.
10.
STEP 10:
Put the battery back to the frame.
WWW.TORPMOTORS.COM
8
CONNECT THE CONTROLLER
TO THE APP
for further setup.
HOW TO CONNECT?
To connect the TC1000 controller with the
Torp Controller App, first go to the Google
Play Store (Android) or AppStore (IOS) and
download the App to your smartphone.
-Allow the App to access the phone's
location, photos and media and accept the
Terms & Conditions.
-Put the key into the ignition and turn on
your bike.
-The App will automatically detect your
controller.
-Choose your controller from the list. The
Bluetooth ID can be found on the label on
the side of the controller.
-Now you are connected and can start
setting up your controller.
We suggest you always ride with the app set to the 1s screen. This is how the Torp Controller
App will be able to recognize potential errors which will help our support team with detecting
and solving any problems that might occur with the controller.
IMPORTANT: After the installation make sure to calibrate the throttle and Hall sensors! Go to the
5th screen of the Torp App and click the CALLIBRATION button. Then follow the setup Wizard.
CALLIBRATION must be repeated after each firmware update!
1
2
3
4
5
6
7
8
WWW.TORPMOTORS.COM
9
1st Screen: GAUGE
The TC1000 controller is compatible with the stock SurRon display, where
you will be able to track your speed and distance. However, we
recommend using your smartphone as the display during the rides.
The first screen serves as a gauge, showing all your riding information in
real time. Here are also displayed all the potential errors and warnings.
THE APP OVERVIEW.
1-Motor Temperature: Monitor the Motor
Temperature in real-time.
2-Battery Temperature: Monitor the battery
temperature in real-time.
3-Controller Temperature: Monitor the
battery temperature in real-time.
4-Power Gauge: Displays the power.
5-Warnings & Errors: All Warnings and
Errors are displayed here. More details on
their meaning can be found in a table below.
6-Battery Info: State of charge (SOC),
battery voltage, and battery current.
7-Motor Info: Motor RPMs, Motor Power and
Motor Current.
8-Predict your Trip: Check the distance you
have passed, the amount of regenerated
energy, and the consumption of the battery.
You can plan your trip based on this
information.
9-BMS!: There is a problem with BMS
communication. Please check the wiring!
9
Table des matières
Autres manuels TORP Contrôleurs
