Toro 07297 Manuel utilisateur

Printed in the USA

2001 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Canopy Kit

Workman1100/2100 and TwisterUtility Vehicle

Model No. 07297

Model No. 07297R

Form No. 3326-769 Rev B

Installation Instructions

Safety and Instruction Decals

Safety decals and instructions are easily

visible to the operator and are located near

any area of potential danger. Replace any

decal that is damaged or lost.

104-6731

Assembly

1. Position the machine on a level surface. Set the parking

brake, turn the ignition off, and remove the key.

If you leave the key in the ignition switch, someone

could accidently start the engine and seriously

injure you or other bystanders.

Remove the key from the ignition switch before

you do any maintenance.

Caution

2. If your vehicle has a Roll Over Protection System

(ROPS), proceed to step 3. If your vehicle does not

have a ROPS, proceed as follows:

A. Loosely attach the support brackets to the rear

support tube with 8 screws, 4 (5/16 x 2-3/4 in.) and

4 (5/16 x 1-3/4 in.); 16 flat washers (5/16 in.); and 8

flange nuts (5/16 in.) (Fig. 1).

B. Loosely attach the support brackets to the vehicle

with 8 screws (5/16 x 1 in.), 16 flat washers

(5/16 in.), and 8 flange nuts (5/16 in.) (Fig. 1).

3. Remove the rear bolt that holds the front fender to the

dash and front frame support on each side of the

vehicle. Do not remove the fenders from the vehicle

(Fig. 1).

Figure 1

1. Rear support tube

2. Left-hand support bracket

3. Screw, 5/16 x 2-3/4 in.,

and washer, 5/16 in.

4. Screw, 5/16 x 1-3/4 in.,

and washer, 5/16 in.

5. Flange nut and washer,

5/16 in.

6. Screw, 5/16 x 1 in,. and

washer, 5/16 in.

7. Left-hand front fender

8. Right-hand front support

9. Left-hand front support

4. Slide the slotted bracket on the front support between

the fender and vehicle. Loosely attach the front supports

to the floor of the vehicle using the existing hardware

on the vehicle (Fig. 1).

5. Secure the fenders with the bolts removed in step 3.

6. Loosely attach the canopy to the front supports using 4

long screws (5/16 x 2-3/4 in.), 8 flat washers (5/16 in.),

and 4 flange nuts (5/16 in.) (Fig. 2).

Note: The canopy support is already loosely attached to the

canopy (Fig. 2).

Figure 2

1. Canopy

2. Right-hand front support

3. Left-hand front support

4. Screw, 5/16 x 2-3/4 in.,

and washer, 5/16 in.

5. Flange nut and washer,

5/16 in.

6. Canopy support

7. If your vehicle has a ROPS, insert the clinch nuts into

the holes in the ROPS (Fig. 3). Lift the canopy and

attach it to the ROPS with 2 screws (3/8 x 1 in.) and 2

flat washers (3/8 in.) (Fig. 3). If your vehicle does not

have a ROPS, lift the canopy assembly and attach it to

the rear support tube with 2 screws (5/16 x 2 in.), 4

washers (5/16 in.), and 2 flange nuts (5/16 in.) (Fig. 4).

Figure 3

Vehicle with ROPS

1. ROPS

2. Clinch nut

3. Canopy

4. Screw, 3/8 x 1 in., and

washer 3/8 in.

Figure 4

Vehicle without ROPS

1. Rear support tube

2. Canopy

3. Screw, 5/16 x 2 in., and

washer, 5/16 in.

4. Flange nut and washer,

5/16 in.

8. Starting at the bottom of the vehicle and working your

way to the top, tighten all of the fasteners.

9. Adjust the front suspension; refer to Adjusting the Front

Suspension in the vehicle Operator’s Manual.

Ce manuel convient aux modèles suivants

Autres manuels Toro Véhicule utilitaire

Toro

Toro Workman MDX-D Manuel utilisateur

Toro

Toro Workman HDX Auto Manuel utilisateur

Toro

Toro 07390H Workman HDX-Auto Manuel utilisateur

Toro

Toro 7220 Manuel utilisateur

Toro

Toro 07277 Workman 2110 Manuel utilisateur

Toro

Toro Workman GTX Series Manuel utilisateur

Toro

Toro 7359 Manuel utilisateur

Toro

Toro 127-7377 Manuel utilisateur

Toro

Toro Workman GTX Manuel utilisateur

Toro

Toro Workman 07040 Manuel utilisateur

Toro

Toro Workman 07369 Manuel utilisateur

Toro

Toro Workman 07235 Manuel utilisateur

Toro

Toro Workman 07143 Manuel utilisateur

Toro

Toro 7253 Manuel utilisateur

Toro

Toro 07390 Workman HDX-Auto Manuel utilisateur

Toro

Toro 07385 Workman HDX-D Manuel utilisateur

Toro

Toro 133-7128 Manuel utilisateur

Toro

Toro Trans Pro 100 Manuel utilisateur

Toro

Toro 7253 Manuel utilisateur

Toro

Toro 12004 Manuel utilisateur

Toro

Toro 07253TC Manuel utilisateur

Toro

Toro 7287 Manuel utilisateur

Toro

Toro Groundsmaster 360 Manuel utilisateur

Toro

Toro 07252TC Workman 1100 Manuel utilisateur

Manuels Véhicule utilitaire populaires d'autres marques

Polaris

Polaris ACE 900 SP Manuel utilisateur

TrailMax

TrailMax T-12-UR Manuel utilisateur

Floe

Floe Cargo Max 9.5-73 Manuel utilisateur

Taylor-Dunn

Taylor-Dunn B0-050-00 Manuel

Taylor-Dunn

Taylor-Dunn ET 3000 Manuel utilisateur

Kayo

Kayo S70 Manuel utilisateur

Range Road

Range Road RR608 Manuel utilisateur

Landoll

Landoll 900D Series Manuel utilisateur

pronovost

pronovost PUMA-10000 Manuel utilisateur

SSI SCHAEFER

SSI SCHAEFER WEASEL LITE Manuel utilisateur

Club Car

Club Car TURF 272 2005 Manuel

Cushman

Cushman Turf Truckster 84069 Manuel utilisateur

BERG

BERG Large Trailer Manuel utilisateur

Cub Cadet

Cub Cadet Big Country 641 Manuel utilisateur

Westward

Westward Go-4 XTR Manuel utilisateur

Club Car

Club Car Carryall I 1999 Manuel utilisateur

Etnyre

Etnyre Street Flusher Mode d’emploi

Landoll

Landoll 340 Manuel utilisateur