Toro TimeCutter 74502 Manuel

Printed in the USA

2001 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

TimeCutterZ Riding Mowers

Model No. 74502—Serial No. 220000001 and Up

Model No. 74601—Serial No. 220000001 and Up

Model No. 74701—Serial No. 220000001 and Up

Model No. 74801—Serial No. 220000001 and Up

Form No. 3327-133 Rev A

Setup Instructions

Loose Parts

Note: Use the chart below to verify that all parts have been shipped.

Description Qty. Use

Bolt, 1/4 x 3/4 in.

Washer, 1/4 in.

Nut, 1/4 in.

2Installing the battery

Seat

Knob

Flat washer, 5/16 in.

2Installing the seat

Left-hand control lever

Right-hand control lever

Bolt, 3/8 x 1 in.

Curved washer, 3/8 in.

Installing the motion control levers

Hose coupling 1Washing the underside of the mower

Key 1

Operator’s Manual

Engine Operator’s Manual 1

1Read before operating the machine.

Registration card 1Fill out and return to Toro.

Activating the Battery

Bulk electrolyte with 1.260 specific gravity must be

purchased from a local battery supply outlet.

Danger

Battery electrolyte contains sulfuric acid which is

a deadly poison and causes severe burns.

•Do not drink electrolyte and avoid contact with

skin, eyes or clothing. Wear safety glasses to

shield your eyes and robber gloves to protect

your hands.

•Fill the battery where clean water is always

available for flushing the skin.

•Follow all instructions and comply with all

safety messages on the electrolyte container.

1. Remove the battery from the machine and place it on a

level surface; refer to the Operator’s Manual,

Removing the Battery.

Important Never fill the battery with electrolyte while

the battery is installed in the tractor. Electrolyte could be

spilled on other parts and cause corrosion.

2. Clean the top of the battery with a paper towel.

3. Remove the vent caps from the battery (Fig. 1). Slowly

pour electrolyte into each battery cell until the

electrolyte level is up to the Upper line on the battery

case (Fig. 1).

Important Do not overfill the battery because

electrolyte (sulfuric acid) can cause severe corrosion and

damage to the chassis.

m-5004

Figure 1

1. Vent caps

2. Upper line 3. Lower line

4. Wait five to ten minutes after filling the battery cells.

Add electrolyte, if necessary, until the electrolyte level

is up to the Upper line (Fig. 1) on the battery case.

5. Install the battery vent caps.

6. Charge the battery for 1 hour at 25 to 30 amps or

6 hours at 4 to 6 amps (Fig. 2). Do not overcharge the

battery.

Charging the battery produces gasses that can

explode.

Never smoke near the battery and keep sparks

and flames away from battery.

Warning

7. When the battery is fully charged, unplug the charger

from the electrical outlet, then disconnect the charger

leads from the battery posts (Fig. 2).

8. Install the battery in the tractor and connect the battery

cables; refer to the Operator’s Manual, Installing the

Battery.

Figure 2

1. Positive post

2. Negative post 3. Charger red (+) wire

4. Charger black (–) wire

Installing the Motion Control

Levers

1. Remove the 4 bolts (3/8 x 1 in.) and 4 curved washers

(3/8 in.) which attach the motion control levers to the

control arm shafts for shipping (Fig. 3).

2. Place the levers (with the mounting plates toward the

rear of the machine) on the outside of the control arm

shaft and loosely secure them with the 4 bolts and

curved washers removed in step 1 (Fig. 3).

m–5215

Figure 3

1. Controlarm

2. Bolt, 3/8 x 1 in. 3. Curved washer, 3/8 in.

4. Control arm shaft

3. Position the levers so that the bolts are in the center of

the slots on the lever mounting plate and tighten the

bolts until they are snug.

4. Align the front/rear position of the levers with each

other while in the neutral position. Loosen the bolts

and adjust the levers by sliding and/or tilting the

lever(s) forward or backward until they are properly

aligned.

5. If the ends of the motion control levers hit against each

other while they are in the drive position (Fig. 4) (the

levers are rotated in as far as possible), make

adjustments by moving the levers outward to the

neutral lock position and carefully bend them outward.

Move them back to the drive position and check for

clearance. Repeat if necessary.

Figure 4

Installing the Seat

1. Cut the plastic ties securing the seat to the machine for

shipping. Remove the seat.

2. Remove the knobs and flat washers (5/16 in.) from the

bottom of the seat.

3. Raise the seat support on the machine (Fig. 5).

4. Slide the shoulder bolts on the bottom of the seat into

the slots on the seat support (Fig. 5). Secure the seat to

the seat support with the flat washers and knobs

removed in step 2 (Fig. 5).

m–5579

Figure 5

1. Seat support

2. Shoulder bolt 3. Knob

5. Lower the seat and adjust it if necessary; refer to

Positioning the Seat in the Operator’s Manual.

Checking the Mower

Adjustment

The mower deck was leveled at the factory. If the mower

is not cutting level, adjust the side-to-side level and the

front-to-rear blade slope. See the Operator’s Manual for

the proper procedure.

Checking the Side Discharge

Chute

Remove the plastic tie holding the side discharge chute

up, and lower the chute into place.

Checking the Engine Oil Level

Before you start the engine and use the machine, check

the oil level in the engine crankcase; refer to Checking the

Oil Level in the Operator’s Manual.

Checking the Tire Pressure

Check the front and rear tires for proper inflation. Refer to

Tire Pressure in the Operator’s Manual for the

recommended inflation pressure.

Autres manuels pour TimeCutter 74502

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Toro Tondeuse à gazon

Toro

Toro 3200 Manuel utilisateur

Toro

Toro 71428 Manuel utilisateur

Toro

Toro Recycler 20954 Manuel utilisateur

Toro

Toro Groundsmaster 4500-D Manuel utilisateur

Toro

Toro 78477 Manuel utilisateur

Toro

Toro ProLine 30165 Manuel utilisateur

Toro

Toro 30074 Manuel utilisateur

Toro

Toro Recycler 21131 Manuel utilisateur

Toro

Toro Groundsmaster 1200 Manuel utilisateur

Toro

Toro Diesel Z Master Manuel utilisateur

Toro

Toro 20351-Serial Manuel utilisateur

Toro

Toro 74960 Manuel utilisateur

Toro

Toro TITAN 79348 Manuel utilisateur

Toro

Toro Groundsmaster 30689 Manuel utilisateur

Toro

Toro Z Master 74958 Manuel utilisateur

Toro

Toro 30722 Groundsmaster 300 Manuel utilisateur

Toro

Toro Flex-Force Power System 21356 Manuel utilisateur

Toro

Toro TimeCutter SS 4235 Manuel utilisateur

Toro

Toro Reelmaster 3550-D Manuel utilisateur

Toro

Toro 75501 Manuel utilisateur

Toro

Toro Z334 Z Master Manuel

Toro

Toro 02611 HoverPro 550 Manuel utilisateur

Toro

Toro SUPER RECYCLER 20055 Manuel utilisateur

Toro

Toro Recycler 20958 Manuel utilisateur

Manuels Tondeuse à gazon populaires d'autres marques

RHINO

RHINO 1958 Manuel utilisateur

Wolf Garten

Wolf Garten Compact plus 40 B Manuel utilisateur

Cub Cadet

Cub Cadet LTX 1045 Manuel utilisateur

Craftsman

Craftsman 917.378461 Manuel utilisateur

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuel utilisateur

Challenge

Challenge CH18V2 Instructions de fonctionnement

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuel utilisateur

DEWEZE

DEWEZE ATM-725 Manuel d'utilisation

Weed Eater

Weed Eater 180083 Manuel utilisateur

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuel utilisateur

Better Outdoor Products

Better Outdoor Products Quick Series Manuel utilisateur

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuel d'utilisation

MTD

MTD 795, 792, 791, 790 Manuel utilisateur

Dennis

Dennis FT 610 Manuel utilisateur

AIRFORCE

AIRFORCE F-15 Gen 3 Manuel utilisateur

MTD

MTD 126-220-000 Manuel utilisateur

Stihl

Stihl RMA 443 PV Manuel utilisateur

Yard-Man

Yard-Man 3700-0 Manuel utilisateur