Topcon 3D-MC Manuel d'utilisation et d'entretien
Wheel Loader
3D-MC
Installation and Calibration Manual
For more information contact Synergy Positioning Systems or
visit the Synergy Positioning Systems website at www.synergypositioning.co.nz
Wheel Loader
3D-MC
Installation and Calibration Manual
Part Number 7010-1006
Revision B
©Copyright Topcon Positioning Systems, Inc.
August, 2018
Topcon Positioning Systems, Inc. All rights reserved. The information contained herein may not be used, accessed, copied, stored,
displayed, sold, modified, published or distributed, or otherwise reproduced without express written consent for Topcon.
Table of Contents
ii
P/N: 7010-1006
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Introduction
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
System Components—Hardware and Software . . . . . . . . . . . . . . . . . . . . . . . 1-1
Sensor Angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Basic Cable Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Tilt Sensor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
TS-i3 Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
TS-i3 Sensor Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Attachment/Bucket Sensor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Non Quick Release Attachment/Bucket Sensor Installation. . . . . . . . . . . . . . . . . 2-3
Quick Release Attachment/Bucket Sensor Installation . . . . . . . . . . . . . . . . . . . . 2-4
Boom Sensor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Body Sensor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
GNSS Antenna, Mount, and Mast Installation . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Machine Setup and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Entering Sensor Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Taking Machine Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Entering Sensor Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Light Bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Machine Configuration Complete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Body Sensor Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Boom Sensor Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Attachment/Bucket Sensor Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Attachment/Bucket Edge Sensor Calibration . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Sensor Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
General Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Radio Usage Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Usage Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Preface
iii
P/N: 7010-1006
Preface
Thank you for purchasing this Topcon product. The materials available in this Manual (the “Manual”)
have been prepared by Topcon Positioning Systems, Inc. (“TPS”) for owners of Topcon products, and
are designed to assist owners with the use of the receiver and its use is subject to these terms and
conditions (the “Terms and Conditions”).
Terms and Conditions
Use
This product is designed to be used by a professional. The user should have a good knowledge of the
safe use of the product and implement the types of safety procedures recommended by the local
government protection agency for both private use and commercial job sites.
Copyrights
All information contained in this Manual is the intellectual property of, and copyrighted material of
Topcon Positioning Systems (TPS). All rights are reserved. Do not use, access, copy, store, display,
create derivative works of, sell, modify, publish, distribute, or allow any third party access to, any
graphics, content, information or data in this Manual without TPS’ express written consent and may only
use such information for the care and operation of the receiver. The information and data in this Manual
are a valuable asset of TPS and are developed by the expenditure of considerable work, time and
money, and are the result of original selection, coordination and arrangement by TPS.
Trademarks
Topcon®, Topcon Positioning Systems™, 3D-MC® are trademarks or registered trademarks of TPS.
GX-55, GX-75, MC-i4, TS-i3 are trademarks of TPS. Windows® is a registered trademark of Microsoft
Corporation. The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of
such marks by Topcon Positioning Systems, Inc. is used under license. Other product and company
names mentioned herein may be trademarks of their respective owners.
Disclaimer of Warranty
EXCEPT FOR ANY WARRANTIES IN AN APPENDIX OR A WARRANTY CARD ACCOMPANYING THE
PRODUCT, THIS MANUAL AND THE RECEIVER ARE PROVIDED “AS-IS.” THERE ARE NO OTHER
WARRANTIES. TPS DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR USE OR PURPOSE. TPS AND ITS DISTRIBUTORS SHALL NOT BE LIABLE FOR TECHNICAL
OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE OR USE OF THIS
MATERIAL OR THE RECEIVER. SUCH DISCLAIMED DAMAGES INCLUDE BUT ARE NOT LIMITED TO
LOSS OF TIME, LOSS OR DESTRUCTION OF DATA, LOSS OF PROFIT, SAVINGS OR REVENUE, OR LOSS
OF THE PRODUCT’S USE. IN ADDITION TPS IS NOT RESPONSIBLE OR LIABLE FOR DAMAGES OR
COSTS INCURRED IN CONNECTION WITH OBTAINING SUBSTITUTE PRODUCTS OR SOFTWARE,
CLAIMS BY OTHERS, INCONVENIENCE, OR ANY OTHER COSTS. IN ANY EVENT, TPS SHALL HAVE NO
LIABILITY FOR DAMAGES OR OTHERWISE TO YOU OR ANY OTHER PERSON OR ENTITY IN EXCESS OF
THE PURCHASE PRICE FOR THE RECEIVER.
Please read the following terms and conditions carefully.
Preface
Preface
iv
P/N: 7010-1006
License Agreement
Use of any computer programs or software supplied by TPS or downloaded from a TPS website (the
“Software”) in connection with the receiver constitutes acceptance of these Terms and Conditions in
this Manual and an agreement to abide by these Terms and Conditions. The user is granted a
personal, non-exclusive, non-transferable license to use such Software under the terms stated herein
and in any case only with a single receiver or single computer. You may not assign or transfer the
Software or this license without the express written consent of TPS. This license is effective until
terminated. You may terminate the license at any time by destroying the Software and Manual. TPS
may terminate the license if you fail to comply with any of the Terms or Conditions. You agree to
destroy the Software and manual upon termination of the use of the receiver. All ownership, copyright
and other intellectual property rights in and to the Software belong to TPS. If these license terms are
not acceptable, return any unused software and manual.
Confidentiality
This Manual, its contents, and the Software (collectively, the “Confidential Information”) are the
confidential and proprietary information of TPS. You agree to treat TPS’ Confidential Information with
a degree of care no less stringent that the degree of care you would use in safeguarding your own
most valuable trade secrets. Nothing in this paragraph shall restrict you from disclosing Confidential
Information to your employees as may be necessary or appropriate to operate or care for the receiver.
Such employees must also keep the Confidentiality Information confidential. In the event you become
legally compelled to disclose any of the Confidential Information, you shall give TPS immediate notice
so that it may seek a protective order or other appropriate remedy.
Website; Other Statements
No statement contained at the TPS website (or any other website) or in any other advertisements or
TPS literature or made by an employee or independent contractor of TPS modifies these Terms and
Conditions (including the Software license, warranty and limitation of liability).
Safety
Improper use of the receiver can lead to injury to persons or property and/or malfunction of the
product. The receiver should only be repaired by authorized TPS warranty service centers.
Miscellaneous
The above Terms and Conditions may be amended, modified, superseded, or canceled, at any time
by TPS. The above Terms and Conditions will be governed by, and construed in accordance with, the
laws of the State of California, without reference to conflict of laws.
Preface
Preface
v
P/N: 7010-1006
Manual Conventions
This manual uses the following conventions:
Convention Description Example
Bold Menu, or drop-down menu selection File > Exit (Click the File menu and click
Exit)
Name of a dialog box or screen From the Connection screen...
Button or key commands Click Finish.
Mono User supplied text or variable Type guest, and click Enter.
Italic
Reference to another manual or help document Refer to the
Topcon Reference Manual.
Further information to note about system configuration, maintenance, or setup.
Supplementary information that can have an adverse affect on system operation,
system performance, data integrity, or measurements.
Notification that an action has the potential to result in minor personal injury,
system damage, loss of data, or loss of warranty.
Notification that an action has the potential to result in personal injury or property
damage.
Notification that an action has the potential to result in severe personal injury or
death.
System Components—Hardware and Software
1-1
P/N: 7010-1006
Introduction
This manual describes the installation and calibration of the Wheel Loader system for 3D-MC
applications.
When used with two Topcon GNSS Antennas and a MC-i4 Controller to provide positioning and heading
information, the three tilt sensors accurately measure the gravity-referenced angles of the Wheel
Loader’s body, boom, and bucket. This information is sent to the GX-55/GX-75 Control Box to provide
precise 3D guidance. Each sensor is configured and calibrated for its specific location on the Wheel
Loader.
System Components—Hardware and Software
Table 1-1 lists the hardware and software components of the Wheel Loader system.
Table 1-1. Wheel Loader System Components
Hardware Software
TS-i3 tilt sensors (Body, Boom,
Attachment/Bucket)
3D-MC® Software Interface
GX-55/GX75 touchscreen display MCXCONFIG
MC-i4 GNSS machine control receiver
Topcon GNSS Antenna
System Components—Hardware and Software
1-2
P/N: 7010-1006
Introduction
Figure 1-1: Wheel Loader System Components—Receiver, Antenna, Control Box and Sensors
MC-R3MC-i4 Controller/Receiver
GPS AntennasGPS Antenna (2)
GX-60GX-55/GX-75
Control Box
Body Sensor
Boom Sensor
(Mounted Inside Boom)
Attachment/Bucket Sensor
(Mounted Inside Snap-on Well)
The TS-i3 Boom Sensor is mounted on the inside of the Boom.
The TS-i3 Attachment/Bucket Sensor is mounted on the inside of the
Snap-on Well.
The TS-i3d Body Sensor is mounted on the body of the Wheel Loader.
System Components—Hardware and Software
1-3
P/N: 7010-1006
Introduction
Sensor Angles
Sitting in the Cab facing forward, the Sensor Angles are 0° (straight ahead—horizontal),
+90° (straight up—vertical), and -90° straight down, see Figure 1-2.
Figure 1-2:
Basic Cable Connections
Figure 1-3 shows the basic cabling connections for the Wheel Loader system. When installing
hardware components, use the Topcon supplied fuse or fused power from the Wheel Loader.
Figure 1-3: Basic Cable Connections for the Wheel Loader System
Connect the System ground to the frame side of the Ground Disconnect
Switch, do not connect the ground directly to the Wheel Loader’s Battery
Terminal.
Table des matières
