TOOL WAREHOUSE SG-8900 Manuel utilisateur
SG-8900
AUTOMOBILE SPOT MACHINE
M
odel
SG-8900
I
nput Voltage220V
Frequency
50HZ
Max Output Power
（KVA）
20
200-8900
2.5-11.5
O
peration mode
o
utput voltage (V )
Auto
Automatic Working Time
0.1-2.5 S
O
ne-side welding（
mm
）
0.6-1.2mm
M
ain machine （
mm
）
65*49*102
W
eight（kg）
70KGS
1. Technical Data
2
Instantaneous output current ( A )
2. Installation
1. Open the package to get the operation manual.
2. Check the type and quantity of the accessories of the machine according to the packing
list.
3.According to the shape of the machine, Finish the machine to install, and adhere to the
machine whether there are other problems, if any problem, please consult the dealer or
service department to solve
3
3. Input power connection
1. Input power wire(Not less than 6 square mm copper
cable)
2. Fuse
3. Connect with input power
4. Ground wire
·The input power connection should be in accordance
with the standard and operated by qualified personnel.
·Disconnect the power connection before this
operation.
·Please select the appropriate fuse.
·Please install the ground wire
·After the operation, please lock the box of main
power switch, and disconnect it to the power supply.
Model just for refer
4
4.Operation
①Operation panel indicator
1.Current digial display
2. Time display
3 Operate tools choose
4.on /off switch
Notice!!!
7 gear is the smallest current,when you starting to welding ,please adjust the samllest gear,if not enough,then adjust to
1 , 2, 3 or more.
DON’T when starting to weld adjust big current!!!!
5
②Welding torch and connector
1.The turn of the screw
2.The torch switch
Function
Number
Remark
Wave welding repair
F010
Washer welding repair
F011
Carbon Rod repair
F019
One-side welding repair
F018
Triangle washer repair
F015
6
5.Working Method
1. One-side welding
Earth clamp
Connect spot welding head with welding torch and lock
Adjust time
Choose the operation mode
Put the welding torch on the workpiece with light
pressure
Note:
1. Please test on other workpiece before this operation, in order to avoid any damage to
auto body surface due to over ranged current or operating duration.
2.The current and duration shall be determined by thickness of body sheet metal.
3.After this operation, the other function operation can be following. If not, please
switch off the machine and disconnect power supply, and arrange all accessories for the
next operation.
7
Note:
1. Please test on other workpiece before this operation, in order to avoid any damage to auto body
surface due to over ranged current or operating duration.
2.The current and duration shall be determined by thickness of body sheet metal.
3.After this operation, the other function operation can be following. If not, please switch off the
machine and disconnect power supply, and arrange all accessories for the next operation.
A Round Washer welding
Install welding head with washer
on welding torch and locked
Adjust time
Choose the operation
mode
Put the welding torch on the workpiece with
light pressure
Remove the welding torch, connect pulling
hammer with washer, and fix the sunken surface.
8
B Triangle washer
Install pulling hammer with a triangle washer on
the torch and lock
Adjust time
Choose the
operation mode
Put the welding torch on the
dent area and start welding
Pull the dent area with hammer
Note:
1. Please test on other workpiece before this operation, in order to avoid any damage to auto
body surface due to over ranged current or operating duration.
2.The current and duration shall be determined by thickness of body sheet metal.
3.After this operation, the other function operation can be following. If not, please switch off
the machine and disconnect power supply, and arrange all accessories for the next operation.
9
Carbon rod heating
Install carbon rod with connection head on
welding torch and lock
Adjust time
Choose the
operation mode
Heat the body around bump
area in one-way direction as
circle with carbon rod
Cool down the heated area with cool water, and make it
recover.
Note:
1. Please test on other workpiece before this operation, in order to avoid any damage to auto
body surface due to over ranged current or operating duration.
2.The current and duration shall be determined by thickness of body sheet metal.
3.After this operation, the other function operation can be following. If not, please switch off
the machine and disconnect power supply, and arrange all accessories for the next operation.
10
Table des matières
Autres manuels TOOL WAREHOUSE Système de soudage
Manuels Système de soudage populaires d'autres marques
TAFA
TAFA 30*8B35 Manuel utilisateur
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Manuel utilisateur
ESAB
ESAB Buddy Arc 145 Manuel utilisateur
CIGWELD
CIGWELD 636804 Guide rapide
Red-D-Arc
Red-D-Arc DC-400 Manuel utilisateur
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Manuel utilisateur
