Tomar Inteligent LED Series Manuel utilisateur
iLED
TOMAR Inteligent LED Series
LED with programmable internal FLASHER
INSTRUCTION SHEET
IS0439-03
03-17-2006
2100 West Obispo
Gilbert, Arizona 85233
(480) 497-4400 (800) 338-3133
FAX (480) 497-4416 (800) 688-6627
E-mail: sales@tomar.com www.tomar.com
TOMAR iLED series dual channel LED warning lamps. Feature 41 programmable flash patterns,
synchronization and are available in lamp sizes 3" x 7", 4" x 6" and 7" x 9".
WIRES
RED +12VDC to activate
BLACK Connect to Chassis GROUND
YELLOW Flash Pattern Selection & Sync Line
ELECTRICAL
Input Voltage: 12VDC thru 28VDC
Complete installation with wire rated for 125% of amperage draw
MOUNTING -
Qty 4 - #6 Screws
WARNING: Do not seal TOMAR LED Lamps. Do not seal the LED lamp to the vehicle
mounting surface. Doing so will prevent water drainage and void the lamps warranty.
CURRENT DRAW - in Steadyburn Mode @ 12vdc
3x7 0.8 Amps
4x6 0.8 Amps
7x9 1.6 Amps
SELECTING FLASH PATTERNS
With the YELLOW wire shorted to +12vdc, turn the unit on. Continue to apply +12vdc to the
YELLOW wire for at least 2 seconds. All LEDs will flash 3 times to indicate you have entered flash
pattern selection mode. While maintaining power, remove the YELLOW wire from +12vdc and the
unit will operate in the currently selected flash pattern.
CYCLE FORWARD
Intermittently short the YELLOW wire once to +12vdc then release.
Repeat until the desired pattern is selected.
CYCLE BACKWARD
Intermittently short the YELLOW wire twice to +12vdc in less than one second.
Repeat until the desired pattern selected.
TO RESET PATTERN #1
Apply +12vdc to the YELLOW wire for at least 3 seconds then release. All LEDs will flash
2 times to indicate that you have reset the flash pattern selection to pattern # 1.
SYNCHRONIZE iLED WARNING LAMPS
To synchronize, first select a flash pattern and program each lamp to the same flash pattern.
Unpredictable results will occur if synchronized lamps have different flash patterns selected.
Connect the YELLOW wires of up to qty 10 synchronized iLED lamps. The 7x9 lamps are
equivalent to 2 lamp units, when determining the number of lamps to synchronize. Do not exceed
100 feet of wire between the furthest synchronized units. For best results connect the BLACK lead
to Chassis Ground.
TM
TM
TM
TM
SELECTABLE FLASH PATTERNS
1. Neobe 150 FPM alternating (Factory Setting)
2. Neobe 150 FPM simultaneous [Phase 0]
3. Neobe 150 FPM combo (2 cycles alt + 2 cycles sim)
4. Neobe 150 FPM California steady (half 150 FPM, half steady)
5. Neobe 150 FPM simultaneous [Phase 1]
6. Neobe 75 FPM alternating
7. Neobe 75 FPM simultaneous [Phase 0]
8. Neobe 75 FPM combo (2 cycles alt + 2 cycles sim)
9. Neobe 75 FPM California steady (half 75 FPM, half steady)
10. Neobe 75 FPM simultaneous [Phase 1]
11. Double flash 250 FPM alternating
12. Double flash 250 FPM simultaneous [Phase 0]
13. Double flash 250 FPM combo (2 cycles alt + 2 cycles sim)
14. Double flash 250 FPM California steady (half 250 FPM, half steady)
15. Double flash 250 FPM simultaneous [Phase 1]
16. Double flash 125 FPM alternating
17. Double flash 125 FPM simultaneous [Phase 0]
18. Double flash 125 FPM combo (2 cycles alt + 2 cycles sim)
19. Double flash 125 FPM California steady (half 125 FPM, half steady)
20. Double flash 125 FPM simultaneous [Phase 1]
21. Single flash 375 FPM alternating
22. Single flash 375 FPM simultaneous [Phase 0]
23. Single flash 375 FPM combo (2 cycles alt + 2 cycles sim)
24. Single flash 375 FPM California steady (half 375 FPM, half steady)
25. Single flash 375 FPM simultaneous [Phase 1]
26. Single flash 150 FPM alternating
27. Single flash 150 FPM simultaneous [Phase 0]
28. Single flash 150 FPM combo (2 cycles alt + 2 cycles sim)
29. Single flash 150 FPM California steady (half 150 FPM, half steady)
30. Single flash 150 FPM simultaneous [Phase 1]
31. Single flash 75 FPM alternating
32. Single flash 75 FPM simultaneous [Phase 0]
33. Single flash 75 FPM combo (2 cycles alt + 2 cycles sim)
34. Single flash 75 FPM California steady (half 75 FPM, half steady)
35. Single flash 75 FPM simultaneous [Phase 1]
36. Neobe 150 FPM Steady Flicker
37. Neobe 75 FPM Steady Flicker
38. Steady burn
39. Multi flash 1 (Patterns 1, 12, 21, 2)
40. Multi flash 2 (Patterns 6, 17, 26, 32)
41. Demo Mode (sequences through patterns # 1 - # 38 )
IS0439-03
03-17-2006
iLED
TOMAR Inteligent LED Series
LED with programmable internal FLASHER
INSTRUCTION SHEET
TM
2100 West Obispo
Gilbert, Arizona 85233
(480) 497-4400 (800) 338-3133
FAX (480) 497-4416 (800) 688-6627
E-mail: sales@tomar.com www.tomar.com
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Tomar Équipement d'éclairage
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
