Toa HY-700 Manuel utilisateur

Table des matières

Autres manuels Toa Intervenants

Manuels Intervenants populaires d'autres marques

argon audio

argon audio IE20 Manuel utilisateur

Denon

Denon SC-N7 Manuel utilisateur

Gemline

Gemline Ace 3952 Manuel utilisateur

Focal

Focal ON WALL 300 Mode d’emploi

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuel utilisateur

SoundLogic

SoundLogic BCCS-6/6395 Manuel utilisateur

Peavey

Peavey DTH 218 Manuel utilisateur

Avantree

Avantree Pluto Air Manuel utilisateur

Morel

Morel Integra Series INTEGRA OVATION 4 Manuel utilisateur

Oppo

Oppo SONICA Manuel utilisateur

Bose

Bose SoundLink Wireless Music System Manuel utilisateur

Rocksteady

Rocksteady Stadium Manuel utilisateur

Bowers & Wilkins

Bowers & Wilkins 4 Manuel utilisateur

Sonance

Sonance SONOS OUTDOOR Series Manuel utilisateur

Electro-Voice

Electro-Voice EVID FM4.2 Manuel utilisateur

Pioneer

Pioneer XW-HTD630 Manuel utilisateur

Onn

Onn BWA16AA002 Manuel utilisateur

HP

HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur

Instruction Manual

SUSPENSION KIT

HY-700

General Description

The HY-700 speaker suspension kit is designed for use with TOA SB- 6S and SB-38W low frequency, vented (bass-reflex)

enclosures. The kit features suspension angle indicators and eyebolt mounts to facilitate speaker positioning.

Handling Precautions

Consult a construction expert to ensure mounting bolts

and cables are made of sufficiently strong material to

securely hold the weight of the speakers.

Ensure all mounting eyebolts are securely tightened and

can not be loosened by prolonged exposure to speaker

vibration.

For maximum security, the use of a 6-point suspension

method such as shown in Figure 1 is highly recommended.

TOA takes no responsibility for accidents or injuries caused by

faulty mounting methods or poorly selected mounting locations.

Figure 1

Parts List

1. Suspension bracket No.1

2. Suspension bracket No.2

3. Eyebolt (M16 x 50)

. Spring lock washer (SW16)

5.

Hex.

nut

(M16)

6. ( + ) wood screw

7. Spring lock washer (SW )

8. Flat washer (W )

4

16

16

16

SB-4 S/SB-38W Speaker Installation

The speaker enclosures have been pre-fit with sus-

pension bracket mounting holes. Working from inside

the enclosure, use a screwdriver to push out the hole

plugs from the four locations where the brackets will

be installed. Referring to Figure 2, install the brackets

and eyebolts, ensuring all screws are securely tight-

ened.

N

ote: Horizontal mounting method for the SB-4 S

As shown in Figure 3, an anchor nut for eyebolt

mounting is already installed inside one corner of

the enclosure, therefore only suspension bracket

No. 1 and the eyebolt need be installed at this

location. Refer again to Figure 2 to install the

brackets for the other three points, ensuring all

screws are securely tightened.

Figure 2

Bracket mounting positions for vertical and horizontal

suspension. ( points each)

This inside

corner only

Figure 3

Eyebolt Angle Adjustment

As shown in Figure , adjust the suspension angle with the eyebolts referring to the angle scale (in 10° step for one scale

mark) of the suspension bracket No.1, and tighten all the hexagon nuts securely after adjustment.

The illustration shows that the eyebolt position is adjusted 30° down from horizontal.

Figure 4

TOA Corporation

KOBE, JAPAN

133-05-201-7

A

HY-700

* Please see the reverse side for English manual.

TOA