Toa HY-38S Manuel utilisateur

Table des matières

Autres manuels Toa Intervenants

Manuels Intervenants populaires d'autres marques

argon audio

argon audio IE20 Manuel utilisateur

Denon

Denon SC-N7 Manuel utilisateur

Gemline

Gemline Ace 3952 Manuel utilisateur

Focal

Focal ON WALL 300 Mode d’emploi

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuel utilisateur

SoundLogic

SoundLogic BCCS-6/6395 Manuel utilisateur

Peavey

Peavey DTH 218 Manuel utilisateur

Avantree

Avantree Pluto Air Manuel utilisateur

Morel

Morel Integra Series INTEGRA OVATION 4 Manuel utilisateur

Oppo

Oppo SONICA Manuel utilisateur

Bose

Bose SoundLink Wireless Music System Manuel utilisateur

Rocksteady

Rocksteady Stadium Manuel utilisateur

Bowers & Wilkins

Bowers & Wilkins 4 Manuel utilisateur

Sonance

Sonance SONOS OUTDOOR Series Manuel utilisateur

Electro-Voice

Electro-Voice EVID FM4.2 Manuel utilisateur

Pioneer

Pioneer XW-HTD630 Manuel utilisateur

Onn

Onn BWA16AA002 Manuel utilisateur

HP

HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur

SUSPENSION KIT

Instruction Manual

HY-38S

General Description

The HY-38S speaker suspension kit is designed for use with TOA SB-38S SB-30W and SB-30S low frequency vented

(bass-reflex) enclosures.

Handling Precautions

Consult a construction expert to ensure mounting bolts

and cables are made of sufficiently strong material to

securely hold the weight of the speakers.

Ensure all mounting eyebolts are securely tightened and

can not be loosened by prolonged exposure to speaker

vibration.

For maximum security the use of a 6-point suspension

method such as shown in Figure 1 is highly recommended.

TOA takes no responsibility for accidents or injuries caused by

faulty mounting methods or poorly selected mounting locations.

Figure 1

Parts List

1. Suspension bracket No.1

2. Square washer

3. Eyebolt (M12 x 50)

4. Spring lock washer (SW12)

4

4

4

4

5.

Hex.

nut

(M12)

6. ( + ) wood screw

7. Spring lock washer (SW4)

8. Flat washer (W4)

4

16

16

16

SB-3 S/SB-30W/SB-30S Speaker Installation

The speaker enclosures have been pre-fit with sus-

pension bracket mounting holes. Working from inside

the enclosure use a screwdriver to push out the hole

plugs from the four locations where the brackets will

be installed. Referring to Figure 2 install the brackets

and eyebolts ensuring all screws are securely tight-

ened.

Note: Horizontal mounting method for the SB-3 S SB-30S

As shown in Figure 3 an anchor nut for eyebolt

mounting is already installed inside one corner of

the enclosure therefore only suspension bracket

No.1 and the eyebolt need be installed at this

location. Refer again to Figure 2 to install the

brackets for the other three points ensuring all

screws are securely tightened.

Figure 2

Bracket mounting positions for vertical and horizontal

suspension. (4 points each)

This inside

corner only

Figure 3

TOA Corporation

KOBE JAPAN

133-01-334-60

Hex. nut (M12)

Spring lock

washer (SW12)

Square washer

wood screw

Spring lock washer (SW4)

Flat washer (W4)

Suspension bracket No.1

Eyebolt (M12 × 50)

HY-38S

* Please see the reverse side for English manual.

133-01-334-60