TMG TMG-ALS03 Manuel utilisateur
►www.tmgindustrial.com 1/4 TOLL FREE:1-877-761-2819
TECHNICAL SPECIFICATIONS
Model
TMG-ALS03
Capacity
600 lbs
Minimum Height
270 mm
Maximum Height
760 mm
Hydraulic Oil
ISO VG 15
SAFETY MARKINGS
Congratulations on your purchase of a TMG Industrial hydraulic lift table. With proper care this table should bring you
years of service.
WARNING - Read, study and follow all instructions before operating this device. Failure to heed these instructions
may result in personal injury and/or property damage.
Throughout this manual you will find the following symbols for caution, warning and danger. Pay particular attention to
the notes preceded by these symbols as they are written for your safety. Ultimately, safe operation of this device rests
with you, the operator.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
This notation is also used to alert against unsafe practices.
Indicates a potentially hazardous situation which, if notavoided could result in death or serious injury.
If you find that the lifting range per stroke is too small: pls lift the table to 2/3 of the maximum height, then
loosen oil plug" and then tighten it.
LIFT TABLE MAIN COMPONENTS
DESCRIPTION QUANTITY
1. Lift table Assembly 1
2. Lifting pedal 1
3. Handle Assembly 1
ASSEMBLY INSTRUCTIONS
1. Your Hydraulic Table is almost completely assembled when you open it. To complete the assembly find the parts
above enclosed with your table.
2. Place the Lifting Pedal (24) into the hole (26), Secure with Bolt M8x25 (25) to fix up.
3. Place the Push Handle (22) into the tube of base assembly (32), secure with Bolt M8x35 (23) to fix up. With brake
thread through the handle assembly and the hole on the base, then with Bolt M8x20 (9) to fix up on the release valve link
bar.
4. Your assembly is complete! Use the rubber mat for the table toop when needed.
►www.tmgindustrial.com 2/4 TOLL FREE:1-877-761-2819
SAFETY PRECAUTIONS
WARNING
WARNING-DO NOT EXCEED RATED CAPACITY
WARNING - Do not use the Hydraulic Table in lifting or moving or persons.
WARNING - This table was designed for use on hard, level surfaces capable of sustaining the load. Use on other than
hard, level surfaces could result in load instability and possible loss of load resulting in property damage and personal
injury.
DANGER - Keep clear of the scissor lifting frame beneath the table for lifting or lowering operations. Scissor lifts have
pinch areas between the frames which can cause serious injury if hands or feet are not well clear of this area.
WARNING - Do not use attachments or adapters of any type to modify this lift.
SAFETY PRECAUTIONS
WARNING - Set the brakes on the rear casters when loading or unloading.
CAUTION - When not in use the table shall be fully lowered. Lock in a safe, dry place and keep away from children.
CAUTION - Do not over-reach. Keep loads evenly balance over the center of the table. Excessive loads on the top or sides
of the table may be unstable with the danger of the table toppling over and causing injury or property damage.
WARNING - Failure to heed these warning may result in personal injury and/or property damage.
GENERAL TIPS FOR SAFE OPERATION
1. Keep work area clean. Cluttered work areas invite injury. Do not use in damp, wet or poorly lit locations.
2. Keep table wiped down and clean. Do not expose to prolonged wet or corrosive conditions.
3. Cover the table and store it in a dry, protected environment.
MAINTAINNENCE
1. Periodically check the tightness of mounting bolts and electrical connections. Remove all dirt or corrosion and always
keep clean.
2. Lubricate the wheels to maintain smooth roiling.
3. Inspect all joints and bolts periodically. Remove from service if any cracking or if the frame is bent or deformed.
HYDRAULIC TABLE CART PARTS LIST
►www.tmgindustrial.com 3/4 TOLL FREE:1-877-761-2819
01
02 03
04
05 05
03
03
06
07
06
07
08
08
09 10
11
12
13
14 16
17
18
18
17
19
20
21
22
23
23
24
25
11
12
26
27
27
28
29
30
03 03
31
31
32
33 33
10
11
12
11
12
10
34
35
36
37
37
38
31
31
03
03
39
40
39
39
39 40
34
03
03
14
15
15
►www.tmgindustrial.com 4/4 TOLL FREE:1-877-761-2819
PARTS LIST
NO
DESCRIPTION
QTY
NO
DESCRIPTION
QTY
1
Pump
1
21
Top table
1
2
Pin
1
22
Brake handle
1
3
Shaft Retaining ring 12
9
23
Bolt M8x35
2
4
Lift frame
1
24
Lifting pedal
1
5
Shaft
2
25
Bolt M8x25
1
6
Pin
2
26
Lifting pedal assembly
1
7
Shaft Retaining ring 8
2
27
Caster assembly
2
8
Wheel
2
28
Pin
1
9
Bolt M8x20
1
29
Shaft retaining 8
1
10
Nut M8
9
30
Bushing
1
11
Washer 8
19
31
Wheel
4
12
Spring washer 8
10
32
Base assembly
1
13
Shaft
1
33
Bolt M8x28
8
14
Shaft retaining ring 20
2
34
Zipper part
1
15
Bearing
2
35
Step handle
1
16
Pin
1
36
Pin 6x22
1
17
Shaft retaining ring 10
2
37
Pin
2
18
Connecting plate
2
38
Rubber mat
1
19
Pin
1
39
Bushing
4
20
Bumper
1
40
Shaft
2
Table des matières
Autres manuels TMG Système de levage
TMG
TMG TMG-1000PML Manuel utilisateur
TMG
TMG TMG-ALS01 Manuel utilisateur
TMG
TMG TMG-ALS05 Manuel utilisateur
TMG
TMG ALPHA 3.5 Manuel de la liste des pièces
TMG
TMG TMG-ALSP60 Manuel utilisateur
TMG
TMG TMG-TPL45 Manuel utilisateur
TMG
TMG TMG-1500PML Manuel utilisateur
TMG
TMG TMG-ALS61 Manuel utilisateur
TMG
TMG TMG-ALT95 Manuel utilisateur
TMG
TMG TMG-ALF90 Manuel utilisateur
Manuels Système de levage populaires d'autres marques
morse
morse 82H-124 Manuel utilisateur
Braun
Braun NL955 Series Manuel utilisateur
haacon
haacon 1889.10 Manuel utilisateur
Protekt
Protekt AT 252 Manuel utilisateur
R. Beck Maschinenbau
R. Beck Maschinenbau HS 600 Manuel utilisateur
Nova Technology International, LLC
Nova Technology International, LLC NAS Series Manuel utilisateur
Genie
Genie Z-60/34 Manuel utilisateur
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manuel utilisateur
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manuel de programmation
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manuel de programmation
