TMG 1260 Manuel utilisateur

Page 0of 12

Page 1of 12

Main specifications

Overall assembled size : L18.2 x W3.66 x H2.2 (m) / L60 x W12 x H7.2 (ft)

Shoulder height : H1.2 (m) / 4ft

Door : W1.2 x H1.8 (m) / 4 x 6 (ft)

Prior to assembly

Please read the instructions carefully before installation. It is important to follow your

local safety regulations and industry standards during installation. Regulations may

include but are not limited to :

Safety helmets, protective eyewear, and clothing

Safety harnesses for all elevated workers

Proper ladder, cage, and safety operation

Check all components and parts before installation. All parts are marked with a part

number, please refer to the parts list to make sure you have all parts.

Choose a day with low or no wind to install, assembly is hard in heavy wind. Do not

make any alterations to the structure. Do not hang any weights on the frame during

installation, including parts. We are not responsible for any damages or injuries caused by

inappropriate installation, unauthorized modifications or extreme weather.

This building is not intended for human occupancy.

It is recommended to tape or add foam/rubber on the frame where joints connect and

where it touches the cover. This will help extend the life span of the cover.

Read the following item list carefully and count the number of items to ensure that all

parts are included prior to setup.

Page 2of 12

TMG-GH126007 Part List

Parts

code

Graphical

Description

Qty

BOX

Peak arch tube

1/1

Upper rafter tube

1/1

Shoulder tube

1/1

Sidewall tube

1/1

Roof purlin

(horizontal tube)

1/1

Base plate

1/1

Door column base plate

1/1

Expansion bolt M10x100mm

1/1

Front door cross tubes

1/1

Rear door cross tubes

1/1

Upper vertical tubes for rear truss

1/1

Lower vertical tubes for rear truss

1/1

Door frame cross pull tube

(front truss)

1/1

Door frame left tube

(front truss)

1/1

Door frame right tube

(front truss)

1/1

Door frame column left tube

1/1

Door frame column right tube

1/1

Door horizontal tube

1/1

Film rolling machine guide tube

1/1

Page 3of 12

Roll film tube

2 group

1/1

Tube clamp

1/1

Door buckle

1/1

Film rolling machine

1/1

Reed groove

1/1

22A

Clip spring

1/1

Eight clip spring

1/1

Pressure film carrier

1/1

Half round head bolt M6x50

1/1

Hex bolt M6x45

132

1/1

Hex bolt M6x80

1/1

Self tapping screw #12x25

316

1/1

28A

Self tapping screw #12x35

1/1

Self tapping screw #12x35

134

1/1

Socket wrench

1/1

Page 4of 12

30A

Hex wrench

1/1

Square plug

1/1

Round plug

1/1

Braided rope

1 bundle

1/1

Adhesive tape

1 volume

1/1

Film

1/1

Board

(not included)

80 metres

Installation steps

Step 1 : Review the whole structure and choose the proper installation site

Choose a solid flat level ground area to set up the building. Do not install the

building on soft ground, wetland, uneven surfaces, sloped surfaces.

We strongly recommend that you build the structure on a solid foundation such as

cement and use anchor bolts on all base plates.

Be aware of the surrounding area. Do not set up the building near snowdrifts, open

flames or exposed electrical wires. Do not keep heat sources near the fabric cover.

Keep the building surroundings clear at all times

Mark the ground in the final building location with a line showing the positions of

base plates, front doors. All lines should be drawn from center to center of all base

plate tubes. Diagonal line X must be equal to Y.

Base plates: all base plates must be installed firmly with expansion bolts (6B) on

this step (refer to figure 1).

Parts used in this step :

Page 5of 12

(31) Base plate (#6)

(2) Door column base plate (6A)

(66) Expansion bolts (6B)

Figure 1

Step 2 : Assemble all trusses

The building includes 15 trusses , Connect all pipes with hex bolt (#26).

Parts used in this step (refer to figure 2) :

(1x15) Peak arch tube (#1)

(2x15) Upper rafter tube (#2)

(2x15) Shoulder tube (#3)

(2x15) Sidewall tube (#4)

(6x15) Hex bolt (#26)

Page 6of 12

Figure 2



Lay down all (15) trusses on the ground as figure 3 when the assembly is all

completed and before moving to next step.

Figure 3

Step 3 : Put up all trusses (refer to figure 4)



Put up the front truss, use hex bolt (#26) to secure the truss to the base plates.



Parts used in this step :

(2) Hex bolt (#26)

Page 7of 12

Figure 4



Repeat above step to put up all other trusses (from 2th to 15th truss), and

connect all purl ins. Now the whole structure is completely up. (refer to figure



Parts used in this step :

(70) Roof purlin (#5)

(5x15) Half round head bolt (#25)

Figure 5

Page 8of 12

Step 4 : Installation of front and rear trusses

Installation of the front truss. (refer to figure 6)

(2) Front door cross tubes (#7)

(1) Door frame cross pull tube (#11)

(1) Door frame left tube (#12)

(1) Door frame right tube (#13)

(1) Door frame column left tube (#14)

(1) Door frame column right tube (#15)

(4) Door horizontal tube (#16)

(4) Tube clamp (#19)

(10) Half round head bolt (#25)

(8) Hex bolt (#26)

(6) Square plug (#31)

Figure 6

Installation of the rear truss. (refer to figure 7)

(2) Rear door cross tubes (#8)

(1) Upper vertical tubes for rear truss (#9)

(1) Lower vertical tubes for rear truss (#10)

(2) Tube clamp (#19)

(4) Hex bolt (#26)

Page 9of 12

Figure 7



The whole structure inspection: check all components and trusses to make

sure the whole structure is squared to the base line drawn at the step 1. All

trusses must be set up righted at 90 degree. All purl ins must be straight in line.

If any purl ins are not in line with they will need to be corrected before moving

to the next step.



Now it is the time to secure all bolts and nuts firmed on the structure. But do

not over-tight the bolts, otherwise the tubes might be damaged.

Step 5 : Installing boards (#36) and reed groove (#22) (refer to figure 8, figure 9)



Fix the board (# 36) with self tapping screw (# 29).



Fix the reed groove (# 22) with the self tapping screw (# 28).



Parts used in this step :

(56) Reed groove (#22)

(280) Self tapping screw (#28)

(134) Self tapping screw (#29)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TMG Kit de serre

TMG

TMG TMG-GH813 Manuel utilisateur

TMG

TMG TMG-GH2030BL Manuel utilisateur

TMG

TMG TMG-GH1030R Manuel utilisateur

TMG

TMG TMG-GH1020R Manuel utilisateur

TMG

TMG TMG-GH2060 Manuel utilisateur

TMG

TMG TMG-GH1010R Manuel utilisateur

TMG

TMG INDUSTRIAL 25100 Manuel utilisateur

TMG

TMG TMG-GHD3060 Manuel utilisateur

TMG

TMG TMG-GH826 Manuel utilisateur

TMG

TMG TMG-GH1020P Manuel utilisateur

Manuels Kit de serre populaires d'autres marques

ACD PRESTIGE

ACD PRESTIGE MR3 H Manuel utilisateur

Vitavia

Vitavia VA0040-TRP Manuel utilisateur

VegTrug

VegTrug Nursery Manuel utilisateur

Riverstone Networks

Riverstone Networks Monticello 041315V Manuel utilisateur

STC

STC Easy Grow 6x12 Greenhouse Manuel utilisateur

CLIMA POD

CLIMA POD Spirit V7 Series Manuel utilisateur

Vitavia

Vitavia GAIA JUMBO Manuel utilisateur

Palram

Palram Harmony 6'x4' Manuel utilisateur

ClearSpan

ClearSpan Storage Master 104598 Manuel utilisateur

Sproutwell

Sproutwell GRANGE - 5 Manuel utilisateur

ACD

ACD Piccolo 03 Manuel utilisateur

Growhouse

Growhouse Lean To 6 x 8 Manuel utilisateur

Riverstone Networks

Riverstone Networks Grower's 181010V Manuel utilisateur

GrowSpan

GrowSpan 500 Series Manuel utilisateur

Robinsons

Robinsons 5ft Wide LEAN-TO Manuel utilisateur

Botanica

Botanica E Manuel utilisateur

PNI

PNI SP6000 Manuel utilisateur

Hortus

Hortus 211-203 Manuel de programmation