TJERNLUND HSJ Guide de l'utilisateur

HSJ POWER VENTER SPECIFICATIONS

Performance curves

Static pressure (inches H2O) vs CFM (std. air) at selected flue gas temps.

NOTE: TO ARRIVE AT TOTAL SYSTEM STATIC PRESSURE REFER TO CURVE

AND ADD .38” TO COMPENSATE FOR VENT HOOD AND WIND RESISTANCE.

MOTOR ELECTRICAL DATA

Volts 115

Hertz 60

RPM 3000

Watts 95

Amps 1.26

Therm. Prot. Yes

MOTOR MECHANICAL DATA

DESCRIPTION

Shaded Pole Yes

Open Yes

Int. Fan Cooled Yes

BEARINGS

Type Sleeve

Material Sintered Iron

UC1 UNIVERSAL CONTROL

Maximum Power Consumption 1/2 Amp @

120 VAC 50/60 Hz + Venter motor load

Pre-Purge: Options (0,15,30,60 seconds)

Post-Purge: Factory set at 2 minutes

Options (0,30 seconds; 1,2,4,8,16 minutes)

Dimensions: 5” x 8” (2’ electrical whip inc.)

SAFETY / INTERLOCK

Fan Proving Switch

5 VDC UC1 board supplied power switched

through Fan Prover. UC1 burner / gas valve

interlock rated for 1 H.P. @ 120 VAC.

MODELS AND APPLICATION:

HSJ (Gas or Oil)

Used as a means of Side Wall Venting gas or

oil appliances which require a Post Purge cycle.

Used also to co-vent two gas heaters within

combined BTU/hr. input listed below (requires

accessory controls). Includes a Fan Proving

Switch and the UC1 Universal Control for 24V,

115V or “dry contact” actuation. LED diagnos-

tics and Pre / Post-purge options are standard

with the UC1.

HSUL-J (Discontinued 8/05)

HS115-J & HST-J (Discontinued 7/02)

Replace above models with HSJ.

Note: Tjernlund Products, Inc. reserves the

right to make changes to specifications without

notification.

ADJUSTMENT ROD

DAMPER

TOLERANCE: ±1/8" UNLESS OTHERWISE NOTED

SHADED POLE MOTOR

3,000 R.P.M.

ADJUSTABLE DAMPER

FAN PROVING PRESSURE SWITCH

4 5/8

3 1/8

9 5/8

4 I.D.

9 7/8

1 7/8

4 3/4

7 5/8

4 I.D.

5 5/8

7 1/2

2 1/4

5 1/4

FIGURE 2061000-3

1 1/2

FAN PROVER SENSOR

SHIELD

DRIP

1 1/8

-SIDE VIEW- -END VIEW- -PLAN VIEW-

P/N 8506001

REV. B 2/06

500°F

400°F

300°F

70°F

1.00

.80

.60

.20

.40

1601401208060 1004020CFM (std air)

DIA.

VENT BTU / HR

MAXIMUM PIPE LENGTH

OILGAS

23'

100'

35'

100'

125,000

100,000

75,000

50,000

4"HSJ

500° F400° F300° F

FIREDFIRED

AT STACK TEMPERATURE

(FT)

INPUT

PIPE

MODEL

TJERNLUND PRODUCTS, INC.

1601 Ninth Street • White Bear Lake, MN 55110-6794

PHONE (800) 255-4208 • (651) 426-2993 • FAX (651) 426-9547

Visit our web site • www.tjernlund.com

HS1 POWER VENTER SPECIFICATIONS

Performance curves

Static pressure (inches H2O) vs CFM (std. air) at selected flue gas temps.

NOTE: TO ARRIVE AT TOTAL SYSTEM STATIC PRESSURE REFER TO CURVE

AND ADD .38” TO COMPENSATE FOR VENT HOOD AND WIND RESISTANCE.

MODELS AND APPLICATION:

HS1 (Gas or Oil)

Used as a means of Side Wall Venting gas or

oil appliances which require a Post Purge cycle.

Used also to co-vent multiple heaters within

combined BTU/hr. input listed below (requires

accessory controls). Includes a Fan Proving

Switch and the UC1 Universal Control for 24V,

115V or “dry contact” actuation. LED diagnos-

tics and Pre / Post-purge options are standard

with the UC1.

HSUL-1 (Discontinued 8/05)

HS115-1 & HST-1 (Discontinued 7/02)

Replace above models with HS1.

Note: Tjernlund Products, Inc. reserves the

right to make changes to specifications without

notification.

70°F

300°F

400°F

500°F

1.00

.60

.20

.40

.80

16014010080 1206040CFM (std air) 20

FIGURE 2011038-3

1 1/2

SHIELD

DRIP

TOLERANCE: ±1/8" UNLESS OTHERWISE NOTED

SHADED POLE MOTOR

3,000 R.P.M.

7 5/8

4 I.D.

5 5/8

7 1/2

2 1/4

5 1/4

ADJUSTMENT ROD

DAMPER

4 5/8

3 1/8

1 1/8

10 3/4

2 1/16

4 I.D.

FAN PROVER SENSOR

134 3/4

FAN PROVING PRESSURE SWITCH

ADJUSTABLE DAMPER

DIA.

VENT BTU / HR

MAXIMUM PIPE LENGTH

OILGAS

35'

27'

100'

60'

57'

12'

100'

92'

100'

30'

100'

40'

87'

100'

150,000

200,000

250,000

300,000

250,000

200,000

150,000

HS1

500° F400° F300° F

FIREDFIRED

AT STACK TEMPERATURE

(FT)

INPUT

PIPE

MODEL

-SIDE VIEW- -END VIEW- -PLAN VIEW-

TJERNLUND PRODUCTS, INC.

1601 Ninth Street • White Bear Lake, MN 55110-6794

PHONE (800) 255-4208 • (651) 426-2993 • FAX (651) 426-9547

Visit our web site • www.tjernlund.com

MOTOR ELECTRICAL DATA

Volts 115

Hertz 60

RPM 3000

Watts 95

Amps 1.26

Therm. Prot. Yes

MOTOR MECHANICAL DATA

DESCRIPTION

Shaded Pole Yes

Open Yes

Int. Fan Cooled Yes

BEARINGS

Type Sleeve

Material Sintered Iron

UC1 UNIVERSAL CONTROL

Maximum Power Consumption 1/2 Amp @

120 VAC 50/60 Hz + Venter motor load

Pre-Purge: Options (0,15,30,60 seconds)

Post-Purge: Factory set at 2 minutes

Options (0,30 seconds; 1,2,4,8,16 minutes)

Dimensions: 5” x 8” (2’ electrical whip inc.)

SAFETY / INTERLOCK

Fan Proving Switch

5 VDC UC1 board supplied power switched

through Fan Prover. UC1 burner / gas valve

interlock rated for 1 H.P. @ 120 VAC.

HS2 POWER VENTER SPECIFICATIONS

Performance curves

Static pressure (inches H2O) vs CFM (std. air) at selected flue gas temps.

NOTE: TO ARRIVE AT TOTAL SYSTEM STATIC PRESSURE REFER TO CURVE

AND ADD .38” TO COMPENSATE FOR VENT HOOD AND WIND RESISTANCE.

MODELS AND APPLICATION:

HS2 (Gas or Oil)

Used as a means of Side Wall Venting gas or

oil appliances which require a Post Purge cycle.

Used also to co-vent multiple heaters within

combined BTU/hr. input listed below (requires

accessory controls). Includes a Fan Proving

Switch and the UC1 Universal Control for 24V,

115V or “dry contact” actuation. LED diagnos-

tics and Pre / Post-purge options are standard

with the UC1.

HSUL-2 (Discontinued 8/05)

HS115-2 & HST-2 (Discontinued 7/02)

Replace above models with HS2.

Note: Tjernlund Products, Inc. reserves the

right to make changes to specifications without

notification.

1.40

1.20

70°F

300°F

400°F

500°F

1.00

.60

.20

.40

.80

400350250200 300150100CFM (std air) 50

FIGURE 2102018-3

1 1/2

DRIP SHIELD

ADJUSTMENT ROD

DAMPER

4 5/8

3 1/8

1 1/8

11 5/8

6 I.D.

8 5/8

6 I.D.

PSC MOTOR

3,000 R.P.M.

FAN PROVER SENSOR

136 1/8

9 1/4

6 1/4

6 I.D.

5 5/8

7 7/8

2 1/4

FAN PROVING PRESSURE SWITCH

ADJUSTABLE DAMPER

TOLERANCE: ±1/8" UNLESS OTHERWISE NOTED

-SIDE VIEW- -END VIEW- -PLAN VIEW-

DIA.

VENT BTU / HR

MAXIMUM PIPE LENGTH

OILGAS

67'

100'

72'

100'

67'

100'

15'

94'

100'

450,000

500,000

550,000

600,000

550,000

500,000

450,000

HS2

500° F400° F300° F

FIREDFIRED

AT STACK TEMPERATURE

(FT)

INPUT

PIPE

MODEL

350,000

400,000

100'

100' 100'

100'

400,000

350,000

100'

TJERNLUND PRODUCTS, INC.

1601 Ninth Street • White Bear Lake, MN 55110-6794

PHONE (800) 255-4208 • (651) 426-2993 • FAX (651) 426-9547

Visit our web site • www.tjernlund.com

MOTOR ELECTRICAL DATA

Volts 115

Hertz 60

RPM 3300

Watts 224

Amps 1.51

Therm. Prot. Yes

MOTOR MECHANICAL DATA

DESCRIPTION

Perm. Split Cap Yes

Open Yes

Int. Fan Cooled Yes

BEARINGS

Type Sleeve

Material Sintered Iron

UC1 UNIVERSAL CONTROL

Maximum Power Consumption 1/2 Amp @

120 VAC 50/60 Hz + Venter motor load

Pre-Purge: Options (0,15,30,60 seconds)

Post-Purge: Factory set at 2 minutes

Options (0,30 seconds; 1,2,4,8,16 minutes)

Dimensions: 5” x 8” (2’ electrical whip inc.)

SAFETY / INTERLOCK

Fan Proving Switch

5 VDC UC1 board supplied power switched

through Fan Prover. UC1 burner / gas valve

interlock rated for 1 H.P. @ 120 VAC.

Autres manuels pour HSJ

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TJERNLUND Ventilateur

TJERNLUND

TJERNLUND AireShare AS1 Manuel utilisateur

TJERNLUND

TJERNLUND UC1 Manuel utilisateur

TJERNLUND

TJERNLUND 950-8302 T-STAT KIT 8504132 Manuel utilisateur

TJERNLUND

TJERNLUND SS1C SIDESHOT WITH UC1 UNIVERSAL CONTROL (VERSION X.02) 8504103 REV... Manuel utilisateur

TJERNLUND

TJERNLUND HSJ Manuel utilisateur

TJERNLUND

TJERNLUND 1 Manuel utilisateur

TJERNLUND

TJERNLUND SS1 SIDESHOT (DISCONTINUED VERSION-PRE UC1 UNIVERSAL CONTROL) 8504041 REV A... Manuel utilisateur

TJERNLUND

TJERNLUND WARRANTY POLICY 8500115 Manuel utilisateur

TJERNLUND

TJERNLUND SS1 SIDESHOT WITH UC1 UNIVERSAL CONTROL (VERSION X.06) 8504102 REV D... Manuel utilisateur

TJERNLUND

TJERNLUND DB2 DUCT BOOSTER Manuel utilisateur

TJERNLUND

TJERNLUND DUCT BOOSTER IN-LINE DUCT FANS 8500380 REV. A... Manuel utilisateur

TJERNLUND

TJERNLUND DRAFT INDUCER DJ-3 Manuel utilisateur

TJERNLUND

TJERNLUND aireshare as1p Manuel utilisateur

TJERNLUND

TJERNLUND HSJ Manuel utilisateur

TJERNLUND

TJERNLUND AD-1 DRAFT INDUCER FOR WOOD BURNING STOVES 8500672 REV. 1... Manuel utilisateur

TJERNLUND

TJERNLUND DRYER DUCT BOOSTER LB2 Manuel utilisateur

TJERNLUND

TJERNLUND WHKI MILLIVOLT APPLIANCE INTERLOCK (RECOMMEND WHKE FOR USE WITH UC1) 8504055 REV 3... Manuel utilisateur

TJERNLUND

TJERNLUND SS1R SIDESHOT (DISCONTINUED VERSION-PRE UC1 UNIVERSAL CONTROL) 8504046 REV... Manuel utilisateur

TJERNLUND

TJERNLUND SS1 SIDESHOT WITH UC1 UNIVERSAL CONTROL (VERSION X.02) 8504102 REV... Manuel utilisateur

TJERNLUND

TJERNLUND HS115-3 Manuel utilisateur

TJERNLUND

TJERNLUND 950-1007 FAN PROVER KIT 8504113 Manuel utilisateur

TJERNLUND

TJERNLUND HS-3 Manuel utilisateur

TJERNLUND

TJERNLUND SS1R SIDESHOT WITH UC1 UNIVERSAL CONTROL (VERSION X.04) 8504117 REV... Manuel utilisateur

TJERNLUND

TJERNLUND HS-3 Guide de l'utilisateur

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage