TiVo Series2 DT Manuel utilisateur

How to connect a digital-to-analog converter

box to your TiVo®Series2TM DVR

Use these instructions if:

·you get your TV programming through an antenna

·you have a TiVo Series2 DVR

As of February 2009, all over-the-air TV signals will change from analog to

digital. Your existing antenna will continue to receive the digital TV signals, but

you need a digital-to-analog converter box to translate the digital signal to the

analog format your TV can display.

These instructions will help you connect the converter box to your

TiVo Series2 DVR so you can continue enjoying your favorite TV programs.

Click here to begin.

Previous step Next step

Before you begin...

Please make sure you have the following before you begin

connecting your digital-to-analog converter box.

1. Locate your IR cable. You will need it to complete this setup.

It was included in the carton when you originally purchased

your TiVo DVR. If you cannot locate this cable,

please visit www.tivo.com/store to obtain one.

2. Verify your TiVo DVR’s software version.

Press the TiVo button on your TiVo remote to go to the TiVo Central®

screen. Select Messages & Settings, then Account & System

Information, then System Information.

Your software version must be 9.3.1 or higher.

If you don’t have software version 9.3.1 or higher, connect to the

TiVo service. From Messages & Settings, select Settings,

then Phone & Network, then Connect to the TiVo service.

Once the DVR receives software version 9.3.1, continue with the

next step.

IR cable

Connect your antenna to

the converter box

Your antenna is probably already connected

to the Cable/Antenna RF IN jack on your

TiVo DVR.

Disconnect the antenna from your DVR and

connect it to the IN jack on the converter

box instead.

Also plug in the converter box’s power cord.



Previous step Next step

Converter

Box

Previous step Next step

Connect the converter box

to your TV

Use a Coaxial cable to connect the converter

box’s To TV (RF) jack to the Antenna RF IN

jack on your TV.

Note: This connection is just temporary.



Television

Converter

Box

Previous step Next step

Complete the converter box setup screens

The converter box has some setup screens that you need to complete to ensure that it receives

the digital antenna signals available in your area.

Follow these steps:

1. Make sure the converter box and your TV are powered on.

2. Tune your TV until you see the converter box setup screen (usually on channel 3 or 4

if you used a Coaxial cable in step ).

3. Follow the on-screen instructions using the convert box remote control. This typically

involves scanning for the digital channels that your antenna can receive.

4. When setup is complete, go to the Settings menu on the converter box.

5. IMPORTANT: Find the Standby setting, and turn if “OFF.” This ensures that

the converter box will not automatically power off during a TiVo recording.

6. Find the list of channels in the converter box settings. Verify the listed channels

and uncheck any channels you do not receive.

7. Exit the converter box menu, and go on to the next step.



Previous step Next step

Connect the converter box

to your TiVo DVR

Take the Coaxial cable you used in step and

disconnect it from your TV. Instead, connect it to the

Cable/Antenna RF IN jack on your TiVo DVR.

Converter

Box



Series2TM

DVR

Alternate: For better A/V quality, use a

red/white/yellow Composite A/V cable to connect

the converter box to your TiVo DVR instead of the

Coaxial cable. (Do not connect both.)

Composite

A/V cable

Previous step Next step

Connect the IR cable, and

position the IR emitters

The IR cable’s emitters beam infrared channel change

signals to the IR sensor on your converter box–just like a

remote control does.

An IR cable was included in the carton when you originally

purchased your TiVo DVR. If you cannot locate this cable,

please visit www.tivo.com/store to obtain one.



Converter

Box

Plug the purple end of the IR cable

into the IR jack (usually the lower

CHANNEL CHANGING jack)

on the back of your TiVo DVR.

Place the emitters in front of the converter box’s IR sensor

as shown, one on top of the box and one on bottom.

Be sure both emitters stick out about 1 ½ inches directly in

front of the IR sensor. Use the adhesive strips provided to

keep them in place.

IR cable

IR emitters

Previous step

Connect the TiVo DVR to your TV

Your TiVo DVR should already be connected to your TV, just as it

was before you connected the converter box.

Remember, always connect the OUT jack of one device to the IN

jack of the next. Never connect IN to IN or OUT to OUT.



Repeat Guided Setup

Now that your converter box is connected, you’ll need to repeat Guided Setup on your TiVo DVR.

This instructs the DVR how to change channels on the converter box. To repeat Guided Setup:

1. Turn on your TV and press the TiVo button on your TiVo remote to go to the TiVo Central®screen.

2. Select Messages & Settings, then Restart or Reset System, then Repeat Guided Setup.

3. Follow the on-screen instructions. Be sure to select “Antenna with box” when asked for your

TV programming source.

4. After you complete Guided Setup, you’re finished!



Still need help?

If you still need assistance conjnecting your converter box,

please visit TiVo customer support.

Autres manuels pour Series2 DT

Table des matières

Autres manuels TiVo DVR

TiVo

TiVo Edge Series Manuel utilisateur

TiVo

TiVo TCD652160 Manuel utilisateur

TiVo

TiVo Series 2 Manuel utilisateur

TiVo

TiVo Mini Mode d’emploi

TiVo

TiVo Series 2 Manuel utilisateur

TiVo

TiVo Series2 DT Mode d’emploi

TiVo

TiVo Blue Ridge Dream Manuel utilisateur

TiVo

TiVo DVR Mode d’emploi

TiVo

TiVo Series2 DT Mode d’emploi

TiVo

TiVo Series2 DT Manuel utilisateur

TiVo

TiVo Roamio OTA Manuel utilisateur

TiVo

TiVo Series1 Manuel utilisateur

TiVo

TiVo Series3 HD Manuel utilisateur

TiVo

TiVo T6 Manuel utilisateur

TiVo

TiVo Roamio Manuel utilisateur

TiVo

TiVo Series2 DT Fiche technique

TiVo

TiVo Pace XG1 Manuel utilisateur

TiVo

TiVo Roamio I PRO Manuel utilisateur

TiVo

TiVo T6 Dimensions

TiVo

TiVo Premiere XL Manuel utilisateur

TiVo

TiVo Roamio Mode d’emploi

TiVo

TiVo Series3 HD Manuel utilisateur

TiVo

TiVo Roamio Manuel utilisateur

TiVo

TiVo THR22-100 Manuel utilisateur

Manuels DVR populaires d'autres marques

FLIR

FLIR M3100E Series Manuel utilisateur

VTRACKPRO

VTRACKPRO FPRO300 Manuel utilisateur

Swann

Swann NVR-7085 models Manuel utilisateur

XtendLan

XtendLan DVR-1670C Manuel utilisateur

urmet domus

urmet domus 1093/004AHD Manuel utilisateur

Holux

Holux M1 Manuel utilisateur

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Manuel utilisateur

Whistler

Whistler D16VRS Manuel utilisateur

Defender Security

Defender Security 82-20235 Manuel utilisateur

MISUMI

MISUMI MP-WF100M Manuel utilisateur

Speco

Speco D8HU Manuel utilisateur

UST

UST DDR-E04AA Instructions d'utilisation

Consolidated

Consolidated Digital Video Recorder Manuel utilisateur

Mace

Mace DVR0404RW Guide de démarrage rapide

RCA

RCA RTD315W Manuel utilisateur

FSM

FSM Colibri Grande PRO Manuel utilisateur

Hauppauge

Hauppauge HD PVR 2 Manuel utilisateur

Identivision

Identivision ICR-PH161i PIONEER Manuel utilisateur