Timex Ironman Transit+ Manuel utilisateur

TIMEX® IRONMAN® TRANSIT+ WATCH

01375_INS20

USER GUIDE …..……..……..……..… 1

05S096000.8.17.20

TRANSIT+

NOTES:

* The Ironman Transit+ may ship in ‘Sleep Mode’ to conserve battery power.

Press and hold any button for 2-3 seconds to wake up the watch.

** Prolonged exposure to salt water and sunlight may result in discoloration over time.

FEATURES:

• Easy Touch Heart Rate

• Daily Activity Monitor

• Workout Mode

• Time/Date (12/24 hour format)

• Chronograph

• Timer

• Daily Alarm

• INDIGLO® night-light

KEY FUNCTIONS:

There are 4 side buttons A, B, C and D. There is a metal button E at the 6H position solely for Heart Rate

measurement.

Press button C to change modes.

The sequence of modes is > Time, Workout, Workout Data, Chrono, Timer, Alarm.

Button E is solely for heart rate measurement.

EASY TOUCH HEART RATE:

Heart rate can be measured using electrodes on the watch that are located on the metal case back and button

E. In order to check your heart rate you must be wearing the watch on your wrist with the case back in good

contact with your skin.

In any mode, except setting mode, press and hold button E with your finger for approximately 8-10 seconds to

measure your heart rate. The heart rate icon will flash on the display to indicate that heart rate is being

measured.

GUIDELINES FOR MEASURING HEART RATE:

• Do not measure heart rate under water.

• Always press the sensor, button E, directly with the finger. The finger should press button

E with the watch worn tightly around the wrist.

• If your fingers are very cold this might affect the time it takes to take your heart rate

measurement.

• If you have very dry skin, moisten the fingertip and the skin on the wrist with some water.

• Use of hand creams and lotions can affect the heart rate measurement.

• Clean the back of the watch from time to time with a few drops of water and wipe it dry with

a cloth to remove any grease or oils.

• If the message "do not move" is displayed, try to slow down your body movement in order

to take a more accurate heart rate measurement.

• The heart rate measurement may not work correctly if you have an irregular heart beat.

Heart rate will be displayed with unit BPM (Beats Per Minute) and at the same time % of Max.

Heart rate is displayed at the bottom right corner.

The maximum pulse is calculated as below:

Example: Age = 50

Maximum pulse = 220 – age

Maximum pulse = 220 – 50 = 170

The % of the maximum pulse is calculated as below:

Example: Pulse = 102

% of the maximum pulse = pulse x 100 / maximum pulse

% of the maximum pulse = 102 x 100 / 170 = 60 %

HEART RATE ALARM:

Heart rate boundaries can be set in the Run mode setting. There are three levels for selection. You also can

manually adjust the lower and upper limits for the heart rate in setting mode.

If the measured heart rate is out of the boundary and Heart Rate Alert is set to On, then, there is beep alert and

flashing icon alert on the LCD.

DAILY ACTIVITY TRACKER:

The watch will monitor your daily activity every day, tracking your Steps, Distance and Calories burned.

You can view the records for the previous 7 days.

In Time mode, press button B to view daily activity data (Step, Distance and Calories).

Press button D to activate the last 7 days recall function. Then press button B to recall the last 7 days

information one by one. Press button D to review the data of "Step", "Distance" and "Calories" for that day.

All activity data will be cleared to zero at 12am each day.

TIME MODE:

Press button C until the display shows "TIME". The watch will enter the time display view with Hours, Minutes,

Seconds, Weekday, Month, Date and Day.

In Time mode, press and hold button A to activate the Setting mode. Hour digits will start to flash. Press button

B or D to change the setting digits. You can select the next setting by pressing button C once. The sequence of

setting is Hour, Minute, Second, Year, Month, Date, 12-24 Hour, Contrast, Units, Gender, Age, Height, Weight.

Press B to increase the setting digits and D to decrease the setting digits.

Press and hold button A to exit the setting mode.

WORKOUT MODE:

Press button C until the display shows "WORKOUT". The watch will enter the workout display view with chrono

time (Workout time) on the top line and Dist (Distance) at the lower row.

Press button B to start measurement for the exercise. The message "START" will display at the upper row for 2

seconds. Press B again to stop the measurement. The message "STOP" will be displayed for 2 seconds on the

upper row. Use button B for the run and stop operation.

Press button D to select the view for other data such as Speed (Spd), PACE, STEP, Calorie (CAL), Clock (CLK)

and Distance (dIST).

If exercise is stopped, press and hold button D to clear all data and ready for next new measurement.

When workout is stopped, press and hold button A to enter the Workout Setting mode. The heart rate training

level will start to flash. Press button B or D to adjust the level. There are three level for heart rate setting. Press

button C to select next setting field. The setting sequence is Heart Rate Training Level, Heart Rate Zone High,

Heart Rate Zone Low, Zone Alarm on/off, Step Target.

Press button B to increase setting digits and D to decrease the setting digits.

Press and hold button A to exit the setting mode.

WORKOUT DATA MODE:

Press button C until the mode prompt shows "WORK DATA". Workout data can be retrieved and displayed.

Press button B to recall Data “CHRONO – DIST”, “CAL – STEP” , “PACE”, “BEST PACE” and “SPEED”.

Remark: CHRONO is Workout Time.

CHRONOGRAPH MODE:

Press button C until the mode prompt shows "CHRO". The watch will enter the chronograph display with prompt

"CHRONO" displayed on the upper row. The Time of the Chronograph is displayed at the lower row.

Press button B to start or stop the Chronograph. Press button D while chronograph is running to take "Lap" time

measurement. "Lap" time view will be released in 5 sec automatically.

Press and hold button D while chronograph is stopped to clear the chronograph.

LOOP TIMER MODE:

Press button C until the mode prompt shows "TIMR". The watch will enter the Loop Count Down Timer display

with segment (SG-1 .. SG-6) displayed on the left upper row. The loop counter is displayed at the right upper

row. The Count Down Time is displayed at the lower row.

Press button D to select the segment from SG-1 to SG-6.

Press button B to start or stop the timer operation.

Press and hold button D while timer is stopped to clear all count down time and reload the preset times again.

In Timer mode, press and hold button C to enter the Loop Timer Setting mode. Press button C to select the data

for setting. Press button B or D to change the selected setting digits. The setting sequence is Timer Segment

No, Timer Second, Timer Minute, Timer Hour.

Press and hold button C again to exit the setting mode.

The timer alert beep sound will be generated when each timer counts down to zero. Next segment of the timer

will be loaded and start to count down automatically. The number of loops is 20. Timer will stop automatically.

DAILY ALARM MODE:

Press button C until the mode prompt shows "ALRM". The Alarm-1 prompt "AL-1" will be displayed at the upper

row. The alarm time is displayed at the lower row.

Press button D to select Alarm-1 (AL-1), Alarm-2 (AL-2) and Chime (Hourly chime function).

Press button B to turn the function on / off. If alarm is turned on, "on" will be displayed at the bottom right corner.

If "--" is displayed, the alarm is turned off.

In Alarm mode, press and hold button C to enter the Alarm Time Setting mode. Press button C to select the

data for setting. Press button B or D to change the selected setting digits.

Press and hold button C again to exit the setting mode.

Press any button while alarm sound is active to turn off the sound alert.

INDIGLO® night-light:

The watch provides INDIGLO® backlight for reading the display in dark environments. Press button A in any

mode to turn on the backlight. It lights up the display for 3 seconds.

BATTERY:

The watch operates with a 3V CR2032 battery. Below are some instruction for using and changing battery.

• Never expose the battery to excessive heat such as sunlight, fire or the like.

• Do not short-circuit the battery and do not take it apart.

• If necessary, clean the battery and unit contacts before inserting the battery.

• Dead batteries should be immediately removed from the device.

• Only replace the battery with a 3V CR2032 battery.

EXTENDED WARRANTY

Available in U.S. only. Extend your warranty for an additional 4 years from

date of purchasefor $5. You can pay with AMEX, Discover, Visa or MasterCard

by calling 1 800-448-4639 during normal business hours. Payment must be

made within 30 days of purchase. Name, address, telephone number, purchase

date, and 5-digit model number required. You can also mail a check for $5 to:

Timex Extended Warranty, P.O. Box 1676, Dept. EF, Little Rock, AR 72203.

subsidiaries.

For more brand information, please visit www.IRONMAN.com. IRONMAN® and the ”M-DOT” logo are

registered trademarks of World Triathlon Corporation. Official Product of the IRONMAN® TRIATHLON.

Used here by permission.

Autres manuels pour Ironman Transit+

Table des matières

Autres manuels Timex Montre

Timex

Timex SSQ Manuel utilisateur

Timex

Timex W223 NA Manuel utilisateur

Timex

Timex Ironman Data Link USB Manuel utilisateur

Timex

Timex 696-095000 NA Manuel utilisateur

Timex

Timex 65 Manuel utilisateur

Timex

Timex W197 Manuel utilisateur

Timex

Timex w-215 Manuel utilisateur

Timex

Timex W-105 Manuel utilisateur

Timex

Timex IronMan Run x50+ Manuel utilisateur

Timex

Timex RUN Trainer 2.0 W294 Manuel utilisateur

Timex

Timex Expedition WS4 Manuel utilisateur

Timex

Timex W257 Manuel utilisateur

Timex

Timex CR1216 Manuel d'utilisation

Timex

Timex 865-095000 Manuel utilisateur

Timex

Timex W231 Manuel utilisateur

Timex

Timex W-194 Manuel utilisateur

Timex

Timex TX 800 Series Manuel utilisateur

Timex

Timex 865-095009 NA Manuel utilisateur

Timex

Timex 238-095001 Manuel utilisateur

Timex

Timex W-154-US Manuel utilisateur

Timex

Timex W196 Manuel utilisateur

Timex

Timex W-153 Manuel utilisateur

Timex

Timex MARATHON M434 Manuel utilisateur

Timex

Timex Marathon Manuel utilisateur

Manuels Montre populaires d'autres marques

Pandora

Pandora WATCH2 Manuel utilisateur

Casio

Casio QW-4343 Manuel utilisateur

Suunto

Suunto X6 Manuel utilisateur

Seiko

Seiko N830 Manuel utilisateur

MotionX

MotionX 365 Manuel utilisateur

Garmin

Garmin VENU SQ 2 Manuel utilisateur

QCY

QCY Watch GTC Manuel utilisateur

Canyon

Canyon Cindy CNE-KW41WP Manuel utilisateur

Esq

Esq Watches Guide d'installation

Crane

Crane AA5-CDSM-3A Manuel utilisateur

DETOMASO

DETOMASO MATERA Manuel utilisateur

Geemarc

Geemarc Watch N Shake Manuel utilisateur

LORUS

LORUS W590 Manuel utilisateur

STENLILLE

STENLILLE Actío Manuel utilisateur

Casio

Casio 5594 Manuel utilisateur

Sinn

Sinn HUNTER'S WATCH 3. Edition Manuel utilisateur

Slazenger

Slazenger SLZ800 Manuel utilisateur

iTOUCH

iTOUCH 3360 Manuel utilisateur