TIE TBT1 Manuel utilisateur
Article: 19-90057
USER MANUAL | BENUTZERHANDBUCH | MANUEL D‘UTILISATION
The TBT1 is a 2-in-1 Bluetooth stereo audio adapter
that allows you to switch between receive and trans-
mit modes. You can easily access your audio devices
and send or receive stereo audio wirelessly via Blue-
tooth. No additional software installation is required.
OVERVIEW
INTRODUCTION
ENG
LED indicator
Multifunction button (MFB)
Micro USB charging jack
3.5mm audio port
Secure clip
RX / TX switch button
1 2
ENG
1 2
CHARGING THE TBT1
We strongly recommend that you fully charge the
adapter before using it for the rst time. It takes about
3 hours to fully charge the adapter for the rst time.
1. Charge with computer: connect the micro USB
cable to the adapter power connector and the
standard USB plug to computers USB port.
2. Using an electrical outlet to charge: connect the
micro USB cable to the adapter and the standard
USB plug to a DC 5V adapter.
3. Indicator status:
a. RED = charging
b. OFF = charge completed
Note:
1. When the battery of the adapter is almost empty,
the LED ashes red and a beep sounds. Please
charge the adapter.
2. If you have not used the adapter for a few months,
the LED may not turn red at rst when charging. It
may take 15-35 minutes for the LED to turn red. We
recommend fully charging the adapter at least once
every two months.
Please set the TX/RX switch to the RX position before
starting the TBT1. The TX or RX mode can no longer
be changed during operation.
RECEIVER (RX MODE), SWITCH ON / OFF
Switch on: Press and hold the MFB key for approx. 2
seconds until the LED ashes blue. Beeps will sound
during this process.
Switching o: Press and hold the MFB key for
approx. 3 seconds until the LED ashes red and then
goes out. Beeps sound when you do this.
Pairing with a smartphone
1. Ensure the receiver is turned o.
2. The TBT1 and your smartphone should not be
more than 1 meter apart.
3. Press and hold the MFB button for about 6
seconds until the LED ashes in red and blue
alternatively and fast. The Bluetooth adapter enters
into pairing mode.
4. Activate the Bluetooth function and search the
adapter within your smartphone.
5. Select „ TBT1“ from the device list, follow the steps
and enter pass code 0000 if requested to pair.
6. Connect the TBT1 with your smartphone.
7. After the successful pairing, the LED will ash blue
three times every 2 seconds.
Note:
1. Please make sure your smartphone’s Bluetooth
function is activated before pairing.
RECEIVER
ENG
3 4
ENG
3 4
2. The pairing mode will last for 2 minutes.
3. Once turned on, the TBT1 will search and connect
automatically with the last paired device in working
range.
4. The TBT1 will automatically switch o if no device
can be connected within 5 minutes.
5. Clear the pairing list: Turn the TBT1 o, then press
and hold the MFB button for about 12 seconds
until the LED ashes red for 1 second and then
ashes in blue for 1 second. Afterwards, the
receiver enters into pairing mode automatically.
1. After successful pairing, connect the Bluetooth
receiver to a pair of 3.5mm stereo headphones or
a wired speaker using the included 3.5mm audio
cable. Now you can enjoy your favorite music from
your smartphone or other media players.
2. Press the MFB button once to pause or play the
music.
3. The LED keeps blue when music playing.
4. In standby mode, the LED ashes in blue once
every 1 second.
Please turn the TX/RX switch to TX position before
getting started. TX or RX mode can no longer be
changed during operation.
TRANSMITTER (TX MODE), SWITCH ON / OFF
STREAM MUSIC
Switch on: Press and hold the MFB button for about 2
seconds until the LED ashes blue.
Switching o: Press and hold the MFB button for
about 2 seconds until the LED ashes red and then
goes out.
After connecting the transmitter to a Bluetooth stereo
device, you can enjoy music without wire restriction.
Before pairing, please make sure that your Bluetooth
device supports the Bluetooth prole A2DP.
Pairing procedure
1. Please make sure the transmitter is turned o.
2. Keep the transmitter TBT1 and your Bluetooth
headphone within 1 meter.
3. Press and hold the MFB key for approx. 4 seconds
until the LED ashes blue quickly. The Bluetooth
transmitter then enters into pairing mode.
4. Set your Bluetooth headphone into pairing mode.
5. The transmitter TBT1 will automatically search, pair
and connect with your Bluetooth headphone.
6. After successful pairing, the LED ashes blue twice
every 2 seconds. Now you can connect the trans-
mitter TBT1 to your TV, computer or music player
via the included 3.5mm audiocable to enjoy your
stereo music wirelessly.
TRANSMITTER, PAIRING WITH A BLUETOOTH DEVICE
ENG
5 6
ENG
5 6
Note:
1. The pairing mode will only last for 2 minutes.
2. Once turned on, the transmitter TBT1 will connect
automatically with the last-paired device.
3. The transmitter will automatically switch o if no
devices can be connected within 10 minutes.
4. LED indicator instruction
• In standby mode: ashes blue once every
1 second
• In pairing mode: ashes blue quickly
• Connecting mode: ashes blue twice every
2 seconds
5. Clear the pairing list: turn the Bluetooth transmitter
TBT1 o, then press and hold the MFB button
for about 12 seconds until the LED ashes red
for 1 second and then ashes blue for 1 second.
Afterwards, the transmitter enters into pairing mode
automatically.
• The battery used in this device may cause a re or
present a chemical explosion hazard if mishandled.
• To avoid damage or malfunction of the device, do
not drop the device from great high places.
• Keep the device away from humidity, water and
any other liquid. If the device is exposed to water,
moisture and other liquids, do not operate it to
avoid any electrical shock, explosion and damage
to the device or yourself.
SAFETY INFORMATION
• Do not place or keep the device near any heat
source, such as direct sun light, radiators, stoves
or other apparatus which produces heat. It may
cause explosion, degrade the performance or
reduce battery life.
• Do not modify, repair or disassemble the device
at discretion (especially battery, it may cause an
explosion). Doing this will avoid the warranty.
• Do not place heavy objects on the device.
• Use the supplied and approved charger only.
• Service must be performed by a qualied service
center or the manufacturer.
• Unplug the unit from the wall outlet when unused
for long periods of time and during lightning
storms.
Bluetooth version CSR 4.1 with aptX
low latency
Bluetooth prole A2DP and AVRCP
Working range 10m
TX mode working time 9 hours
RX mode working time 8 hours
Standby time up to 200 hours
Charging time about 3 hours
Charging input voltage DC 5V
Battery 260mAh rechargeable
Li-polymer battery
Dimensions 38 × 39 × 15mm
Net Weight 19g
TECHNICAL SPECIFICATIONS
ENG
7 8
ENG
7 8
Work and standby times may vary when used with
dierent cell phones or other compatible Bluetooth
devices, usage settings, usage types, and environments.
Specications are subject to change and improvement
without notice.
1× Bluetooth Transceiver
1× Micro USB Cable
1× 3.5mm Audio Cable
1× Quick Start Guide
CONTENTS
Article: 19-90057
USER MANUAL | BENUTZERHANDBUCH | MANUEL D‘UTILISATION
Der TBT1 ist ein 2-in-1 Bluetooth Stereo Audio-
Adapter, den Sie über einen einfachen Tastendruck
zwischen Empfangs- und Sendemodus umschalten
können. Integrieren Sie Ihre Audiogeräte problemlos
mit dem TBT1 und senden / empfangen Sie Stereo-
Audiosignale über Bluetooth drahtlos. Eine zusätzliche
Software-Installation ist nicht erforderlich.
ÜBERSICHT
EINFÜHRUNG
DE
LED-Anzeige
Multifunktions-Button (MFB)
Micro-USB-Ladebuchse
3,5-mm-Audioanschluss
Gürtelclip
RX/TX Schalter
910
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
