2. PRESENTATION
2.2 Function of S510
- Lift sensor
There are lift sensors located between the top and middle
- Tilt sensor
There are tilt sensors installed on the mower too, when
mower is tilted over 30 degrees in any direction, it the
seconds.stops working within 2
- Ultrasonic sensors
Compared with traditional bumpers, the ultrasonic sensors
The mower detects obstacles before are much safer.
making contact with them, this makes it safer for children
pets. Ultrasonic sensors (WAVE) are a selectable and
- Bump sensors
The whole top cover is movable. Both front and the two
sides of mower equipped with bump sensors that will
activate when the mower strikes solid, fixed object when
that object is at least 6cm in vertical height from the
supporting surface of the mower. When the bump sensor
- Rain sensors
There are two rain sensors located on the control panel
at to the top cover of mower. The mower will go back
charging station automatically when it's raining.
Turn on: the mower will go back home if it is raining.
Turn off: the mower will go on mowing when it is raining.
- Touch sensor
Touch the handle when the mower is cutting, it will
second. cease function within 0.5
- Wireless remote controller
cover. If the mower is lifted from ground, it will stops
working within 1 second.
activated, the mower will stop movement in that
the obstacle.direction and reverse itself away from
Rain sensors can be selected ON/OFF from control panel.
- Mowing schedule
Set up one week (From Monday to Sunday, once for
schedule from control panel. This each day) cutting
- Anti-theft function
Mower has password protection option to guard against
theft. What's more, the mower can not be turned on
- Cutting width: 25.4cm
- Easy cutting height adjustments
2.5cm-6cm selected with one dial.
- Auto recharge system
When the mower senses a low battery situation, it will
shut off the cutting motor and search for the virtual wire.
Once found it will follow the virtual wire to the charging
station for recharge automatically. Once charging is
complete, the mower will back up a few centimeters
ready to go again in stand by mode.
- Emergency stop switch
There is an emergency switch located on the top of
color. When pressed, the mower willmower and red in
shut down immediately. Rotate the switch clockwise to
function should be used together with AREA function.
without a charging station.
release it.
- Two cutting modes
There are two cutting modes of the mower, go straight
efficiency). and go circle (high
In Auto, mower selects cutting mode intelligently.
It goes straight if the grass is sparse or it has be cut off,
long.and it goes circle if the grass is dense or
In manual mode, the mower will just go were you direct it.
- Pressure sensors
The pressure sensors located on the top cover. If a child
or some thing rides or sits on the mower, it stops
working within 1 second.
-
use 100m-600m of virtual wire). The wire. (we suggest to
station, the virtualmower will follow virtual wire to charging
on the virtual wire wire acts as a virtual fence. It will get
wire and starts cutting inside.
- Mower stops working if virtual wire is cut off or
power off.charging station is
If virtual wire is cut or broken, or the charging station
loose power, the mower will stop working within 3 seconds
- Four steps to safely start the mower
There are four necessary steps to start the mower:
- Overload protect
The brushless cutting motor and each of the two running
are monitored continuously during operation for motors
cause these motors to over-loadany situation that may
In the event this is detected, the mower stops operating.
- Waterproof
Waterproof design, there is an inner cover under top
inside parts from humidify. cover which protect
- LCD display
Virtual wire
The robot lawn mower can't be operated without a virtual
LINE (virtual wire) can be selected ON/OFF from control
- Electronic compass
The mower has compass navigation system to keep it
until it meets charging sheets, then it gets off from virtual
The waterproof class is I
- Subarea setting
You can select Subareas for the mower to cut. This works
well for large lawn. See Section 5.11.
This function should be used together with schedule.
- Different languages selection.
- 4 -
P55.
ON/OFF function.
panel.
1. Connect charging station with power supply by charger
and make sure the recharging light is in green color.
2. Connect virtual wire to charging station and make sure
it is in good connecting(virtual wire light in colorless).
3. Turn on the power button and release the emergency
switch.
4. Input password if selected and select mode.
going straight on inclines.
