Thuli Tables Tour Manuel utilisateur
Tour Owner's Manual
TABLE OF CONTENTS
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 2
Summary of Set-Up & Fold-Down . . . . . . . 2
Identication of Parts . . . . . . . . . . . . . . 3 - 6
Table Set-Up . . . . . . . . . . . . . . . . . . . . . 7 - 11
Heapiece Operation . . . . . . . . . . . . . . 11 - 14
Table Operation . . . . . . . . . . . . . . . . . 14 - 17
Table Fold-Down . . . . . . . . . . . . . . . . 18 - 19
Accessories . . . . . . . . . . . . . . . . . . . . 20 - 23
Flexion Distraction & Lateral Flexion . . . 24
Elevating Conversion Base . . . . . . . . . . . 25
Care & Maintenance . . . . . . . . . . . . . . 26 - 27
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Overview of Products . . . . . . . . . . . . . Back
THULI TABLES
www.thulitables.com
youtube.com/thulitables
800-458-4854
facebook.com/thulitables
2
1. Open the table (pg 7)
2. Remove headpiece from storage, engage T-bar
and attach headpiece (pgs 7-8)
3. Erect front legs (pg 8)
4. Attach piston to headpiece (pg 8)
5. Release thoracic section (pg 9)
6. Erect middle legs & attach support braces (pg 9)
7. Erect back legs (pg 9)
SET-UP (pgs 7-9): Begin at the headpiece and progress toward the ankle rest.
Introduction 2
Table Set-Up & Fold-Down: Quick Reference
FOLD-DOWN (pgs 18-19): Reverse the set-up sequence above. Begin at the ankle rest and progress toward the headpiece.
Fold the front half of the table onto to the back half.
Rick Thuli, D.C.
President
Sincerely,
We are pleased to provide you with a chiropractic adjusting table that is elegant,
versatile and engineered with precision. It has been thoroughly inspected and
tested right down to the smallest detail before leaving our shop. We are
condent that it will provide you with many years of reliable service.
Please take the time to read this manual carefully. It will familiarize you with
the table and instruct you on its proper operation and maintenance.
If you have any questions or comments, please contact us.
Thank you for your purchase of a Tour portable table.
3
Pelvic Section
Caudal Section
Thoracic Section
Prone Arm Rest
Pin to close table and
attach headpiece
Caudal Cocking Lever
&Tension Control Rod
Pelvic Cocking Lever
& Tension Control
Rod
Thoracic Cocking Lever
&Tension Control Rod
Closing Block
Ankle Rest
Locking Knob
Mid-Leg
Support Brace
Headpiece
Bracket
Folding
Support Brace
(Left)
Identification of Table Parts 3
Piston
(adjustable)
4
Folding
Support Brace
(Left)
Folding
Support Brace
(Right)
Front Legs
Piston
Remote Control
Lever
Thoracic
Slant Bar
Prone Arm Rest
Pelvic Drop
Mechanism
Thoracic Cocking Lever
& Tension Control Rod
Brace Lock
Folding
Support Brace
(Right)
Thoracic
Hold-Down
Headpiece
Mount Bracket
Pin to close table and
attach headpiece
Mid Legs
Pelvic Cocking Lever
& Tension Control Rod
Thoracic Drop
Mechanism
Identification of Table Parts (folded position) 4
5
Hinge Pin for
Separating Table
Joining Hinge
Brace
Lock
Folding
Support Brace
(Right)
Remote Control
Slot
Joining Hinge Mid-Leg
Support Brace
Headpiece
Cocking Lever
Headpiece
Locking Link
Headpiece
Raising Lever
Caudal Drop
Mechanism
Caudal Cocking Lever
& Tension Control Rod
Paper Tear-Off Bar
Closing Block
Paper Hanger
Slot for
Headpiece Piston
Headpiece Tension
Control Knob
Headpiece
Slide Block
Identification of Table Parts (folded position) 5
Headpiece
Paper
6
Pivot Block
Paper Hanger
Remote Control Lever
Piston Head
Adjustable Buckle for
Prone Arm Rest
Flexion /Extension Piston
Prone Arm Rest
Lowering Lever
T-Bar
Cocking Lever
Straight Drop/
Forward Motion Knob
Remote Control Cable
Headpiece Mounting
Bracket (two holes)
Piston Pin
Slide Block
Tension Control Knob
(not visible)
Paper Hold-Down Wire
Paper Tear-Off Bar
Pin to close table &
attach headpiece
Pivot Pin
Identification of Headpiece Parts 6
7
OPEN THE TABLE
1. Position yourself on the handle side of
the table. Lay the table onto its cushions
so that the Thuli logo is upside down.
2. Remove the pin from the metal bracket.
Open the table by grasping one of the
carrying handles.
3. Set the pin on the oor at the left end
of the table. You will use this pin to
attach the headpiece.
1. Unfasten the Velcro strap and remove the headpiece from its
storage position and place on its cushions.
Note: The strap is not included on Tours with Flexion Distraction.
2. Lift the slide block by grasping the lowering lever and raising
it to a 45 degree angle.
3. Grasp the end of the T-bar with your other hand. Insert it
into the hole in the locking link of the slide block.
4. Lower the slide block to a closed position by applying counter
clockwise (downward) torque to the lowering lever.
HEADPIECE ATTACHMENT
Begin at the headpiece end and progress
toward the ankle rest:
5. To attach the headpiece to the table, line up the hole of the
slide block with the hole of the mounting bracket closest to
the cushions. Insert the pin with a twisting motion.
Note: If you are using the Comfort Pillow, the slide block
will come with a white plastic attachment. Line it up with the
holes of the mounting bracket farthest from the cushions.
Insert the pin with a twisting motion.
Table Set-Up 7
HEADPIECE ATTACHMENT (cont.)
8
HEADPIECE ATTACHMENT (cont.)
2. Raise the front legs from their folded position by grasping
the horizontal crosspiece.
3. Straighten the folding leg support braces and lock them into
place by sliding the black brace locks over the brace joints.
Note: If the brace lock falls down off of the brace joint,
slide the lock back over the joint and exert a slight pressure
perpendicular to the brace at the brace lock. This will provide
sufcient friction to keep the brace lock in place.
4. Swing the headpiece exion/extension piston down toward the
off-centered slot in the slide block.
5. Remove the piston pin from the slide block and raise the front
end of the headpiece to allow the piston to engage in the
off-centered slot. Note: Operating the remote control lever
will allow you to rotate the piston head to align with the
off-centered slot.
6. Attach the exion/extension piston to the slide block by visually
lining up the holes and re-inserting the piston pin.
6. Before raising the front legs from their folded position,
disengage the piston head from its locked position. Squeeze
the remote control lever and retract the piston head from the
hole in the frame.
NEED PHOTO
FRONT LEG SET-UP
Table Set-Up 8
FRONT LEG SET-UP (cont.) FRONT LEG SET-UP (cont.)
9
BACK LEG SET-UP
Swing the two mid-leg support braces up from the back
section of the table and attach them to the middle legs:
Line up the hole in the brace with the brass insert in the middle
leg. Push the mid-leg pin through the brace from the inside of
the leg until the ball (on the end of the pin) is completely
engaged through the brace.
1. Raise the back legs and lock the brace joints into place in the
same fashion as the front and mid-legs.
2. Reattach the Velcro strap through its metal loop.
3. Remove the headpiece paper from storage under the elastic strap.
MID-LEG SUPPORT BRACES
2. Release the Velcro-secured thoracic section.
3. Raise the middle egs by grasping the horizontal crosspiece.
4. Before the brace joints are fully straightened, slide the black
brace locks up toward the brace joints, then straighten the braces
and lock them into place. This step prevents the brace locks
from becoming bound between the middle and front leg brace
joints and is necessary only when setting up the middle legs.
THORACIC RELEASE & MID-LEG SET-UP
1. Install the black remote control lever into the bottom of the
slide block by inserting the cable into the narrow slot and tilt
the cable end of the lever into the slot until it snaps into place.
Note the milled nger recess for later removal of this lever
when folding up the table. Operating this lever will allow the
headpiece to lay ush with the table cushions.
Table Set-Up 9
REMOTE CONTROL LEVER
10
GAS SPRING INSTALLATION (cont.)
Insert the base end mount of the black gas spring in to the slot in
the aluminum mount block which is attached to the cross brace
of the front legs. Do this by pulling outward on the white handled
spring pin, inserting the gas spring base end tab and then releasing
the white handled spring pin until it engages in the tab.
GAS SPRING INSTALLATION (cont.)
Repeat previous step on the operating end of the black gas spring
where it attaches to the abdominal cushion. You may need to
pull up or push down slightly on the abdominal cushion by
grasping the aluminum mount block to help with alignment so
that the engaging spring pin slides in easily.
GAS SPRING INSTALLATION
GAS SPRING & CONTROL LEVER REMOVAL
Remove the Abdominal Swing-Away gas spring and control lever
from its storage location. Note that the control lever is positioned
and attached by a magnetic latch.
Slide the black control lever housing onto the front folding leg
support brace and position it to come into contact with the black
poly lock. It will be held in place with an internal magnet.
Abdominal Swing-Away Set-Up (optional feature) 10
Table des matières
Autres manuels Thuli Tables Équipement médical
