Thermon Terminator ZL Guide de référence

For Power Connecon or End Terminaon Applicaons

Terminator

TM ZL

Lighted Power Connecon/

End Terminaon Kit

INSTALLATION PROCEDURES

Kit Contents

Item Quanty Descripon

1 1

Expediter Assembly

Support Cap with O-Ring

Threaded Grommet Compressor

Grommet

Support Base with O-Ring

2 1 Juncon Box Lid

3 1 Juncon Box Base with O-Ring

4 1 Nut

5 1 Banding

6 1 Banding Guide

7 1

Terminal Blocks with DIN Rail

(Refer to terminal specicaons for maximum

allowable wire size)

8 1 Juncon Box Cord

Dimensions

TerminatorTM ZL INSTALLATION PROCEDURES

Order Separately

PETK Power and End Terminaon Kits (per cable)

PETK-1 for BSX, RSX, VSX-HT

PETK-2 for KSX, HTSX

PETK-3 for HPT, FP

Item Quanty Descripon

1 1 RTV Tube

2 1 Power Connecon Boot

3 1 End Cap

4 1 Tape Strip 6" (PETK-3 only)

5 1 End Terminaon Cauon Label

6 1 GRW-G Grommet (PETK-3 only)

7 1 Ground Sleeve

IP66/Type 4X -60°C ≤Ta ≤ +55°C

Listed Heat Tracing Cable System 137M

Ordinary & Hazardous Locaons

Class I, Division 2, Groups A, B, C, & D

Class II, Division 2, Groups F & G, Class III

Class I, Zone 1, AEx eb IIC T6...T4

09.2238691,-G,-S, Ex eb IIC T6...T4

Tools Required

Cercaons/Approvals

Installaon Precauons

• To minimize the potenal for arcing and re caused by product

damage or improper installaon use ground-fault protecon.

The Naonal Electrical Code (NEC) and Canadian Electrical Code

(CEC) require ground-fault protecon of equipment for each

branch circuit supplying electric heat tracing.

• Installaon must comply with Thermon requirements and

be installed in accordance with the NEC, CEC, or any other

applicable naonal and local codes.

• Component approvals and performance rangs are based on

the use of Thermon specied parts only. User supplied power

connecon ngs must be listed or cered for intended use.

• De-energize all power sources before opening enclosure.

• Avoid electrostac charge. Clean only with a damp cloth.

• Keep ends of heang cable and kit components dry before and

during installaon.

• Individuals installing these products are responsible for

complying with all applicable safety and health guidelines.

Proper personal protecve equipment, or PPE, should be ulized

during installaon. Contact Thermon if you have any addional

quesons.

FMG 10.0022X Ex eb IIC T6...T4, Ex tb IIIC T85°C…T135°C

1725 II 2 GD Ex eb IIC T6...T4, Ex tb IIIC T85°C…T135°C FM 10ATEX0058X

2 64

3 5

TerminatorTM ZL INSTALLATION PROCEDURES

1. Locate bus connecon (HPT and FP only) and

cable as shown. Cut end of cable at angle to aid

in piercing grommet. Leave addional cable for

expansion loop. See page 4 for mulple cable

installaon ps.

4. Insert banding guide into expediter and snap

into place.

2. Insert cable into expediter. If mounted on

boom or side of pipe, punch out weep hole.

Note: For HPT and FP cable, exchange grommet in

Terminator with GRW-G provided in PETK-3.

3. Slide expediter toward pipe and route cable

through support base entry.

7. Terminate cable with appropriate PETK

termination kit. Refer to PETK installation

instrucons.

8. Push excess cable back through expediter.

Tighten cap securely. Tape cable expansion loop

to pipe.

9. Mount juncon box base on expediter. Make

sure to align slots to properly orient juncon

box base. If mounng horizontally, threaded

gland holes must face downward.

5. Mount expediter to pipe using pipe band. Do

not band over cable.

6. Cut o end of cable.

Corporate Headquarters: 100 Thermon Dr • PO Box 609 San Marcos, TX 78667-0609 • Phone: 512-396-5801 • 1-800-820-4328

For the Thermon oce nearest you visit us at . . . www.thermon.com

10. Install power cable (if necessary). 11. Install quick mount terminal blocks and ghten

screws (if necessary). Complete system wiring.

Tightening torque 1.5 Nm–1.8 Nm (1.1 -lb–1.3

-lb).

12. Install juncon box lid and twist hand ght.

Insert screwdriver into ratchet slots located on

side of juncon box base.

13. Use screwdriver to ratchet on juncon box lid.

Lid will rotate 30 degrees. Lid latch mechanism

fully engaged. To remove lid, repeat steps 12

and 13 but in the opposite direcon.

Locate bus connecon (HPT and FP only) and cable

as shown. Cut end of cable at angle to aid in piercing

grommet. Leave addional cable for expansion loop.

Two Cable Layout Tips

Insert two cables into expediter.

Note: For HPT and FP cable, exchange grommet in

Terminator with GRW-G provided in PETK-3.

Power Connecon (1 to 2 Heang Cables)

Wiring Details

End Terminaon (1 Heang Cable Only)

Ground

Power Supply

Ground

L2 or N

Ground

Form PN50848-0519

TerminatorTM ZL INSTALLATION PROCEDURES

Manuels testeur de câbles populaires d'autres marques

VOLTCRAFT

VOLTCRAFT CT-2 Manuel utilisateur

Whirlwind

Whirlwind Connect DCT-9 Manuel utilisateur

Triplett

Triplett CTX200 Manuel utilisateur

Greenlee

Greenlee 45395 Manuel utilisateur

Test-Um

Test-Um Validator-NT NT955 Manuel utilisateur

Fluke

Fluke MicroMapper Manuel utilisateur

Radiodetection

Radiodetection RD8100 Manuel utilisateur

Vonaq

Vonaq EasyCheck 900 Manuel utilisateur

Softing

Softing CableMaster CM200 Manuel utilisateur

Microtest

Microtest 8751 Manuel utilisateur

Psiber Data Systems

Psiber Data Systems 20 Manuel utilisateur

Platinum Tools

Platinum Tools LANSeeker TP500C Manuel utilisateur

Triplett

Triplett WireMaster HDMI2 Manuel utilisateur

Tenmars

Tenmars LC-90 Manuel utilisateur

BIRD

BIRD SITE ANALYZER SA-1700EX Manuel utilisateur

Softing

Softing WireXpert 4500 Manuel utilisateur

Vision

Vision V18-310 Manuel utilisateur

Black Box

Black Box Scan-LAN 80 Manuel utilisateur