Thermo Scientific 3960 Mode d'emploi

Model 3960 Series

29 cu ft Environmental Chamber

Operating and Maintenance Manual 7003960 Rev. 15

Visit us online to register your warranty

www.thermoscientific.com/warranty

Thermo Scientific

MANUAL NUMBER 7003960

15 29318/IN-4272 12/14/12 Clarified usage on 3960-06-1 exploded drawing list ccs

14 24921/IN-3939 2/16/12 Removed accessory list - 7-2 ccs

13 27292/IN-4073 9/29/11 Revised drawings on pgs 8-3 and 8-4, spacers and power supply kit ccs

12 25454/IN-3930 4/16/09 Corrected figures on page 1-1 to 3960 ccs

11 24809/IN-3872 10/10/08 Updated temp probe part number to 290138 ccs

10 -- 8/27/07 Removed typo ‘connected to gas supply’ in Start-Up ccs

9 23572/IN-3320 10/03/06 Updated seal on blower motor mount (drawing 1900014-06-1r2) ccs

-- -- 12/2/04 Clarified operating temperature setpoint range ccs

-- -- 1/19/04 Clarified overtemp operation aks

8 21980/IN-3156 11/7/03 Added min/max load and analog output board max external cable length ccs

Preface

29 cu ft Environmental Chamber i

*All units are 50/60 Hz.

Models covered by this manual

Model Voltage*

3960 100-120

3961 200-230

Warning If the chamber is not used in the manner specified is in this

operating manual, the protection provided by the equipment design may

be impaired. s

Thermo Scientificii 29 cu ft Environmental Chamber

Preface

Important Read this instruction manual. Failure to read, understand and follow the instructions in this manual

may result in damage to the unit, injury to operating personnel, and poor equipment performance. s

Caution All internal adjustments and maintenance must be performed by qualified service personnel. s

Material in this manual is for information purposes only. The contents and the product it describes are subject

to change without notice. Thermo Fisher Scientific makes no representations or warranties with respect to this

manual. In no event shall Thermo be held liable for any damages, direct or incidental, arising out of or related

to the use of this manual.

Thermo Scientific 29 cu ft Environmental Chamber iii

Preface

Important operating and/or maintenance instructions. Read the accompanying text carefully.

Potential electrical hazards. Only qualified persons should perform procedures associated with this

symbol.

Equipment being maintained or serviced must be turned off and locked off to prevent possible injury.

Hot surface(s) present which may cause burns to unprotected skin, or to materials which may be

damaged by elevated temperatures.

Marking of electrical and electronic equipment, which applies to electrical and electronic equipment

falling under the Directive 2002/96/EC (WEEE) and the equipment that has been put on the market

after 13 August 2005.

This product is required to comply with the European Union’s Waste Electrical & Electronic

Equipment (WEEE) Directive 2002/96/EC. It is marked with the WEEE symbol. Thermo Fisher

Scientific has contracted with one or more recycling/disposal companies in each EU Member State

European Country, and this product should be disposed of or recycled through them. Further

information on Thermo’s compliance with this directive, the recyclers in your country and

information on Thermo Scientific products will be available at www.thermofisher.com.

4Always use the proper protective equipment (clothing, gloves, goggles, etc.)

4Always dissipate extreme cold or heat and wear protective clothing.

4Always follow good hygiene practices.

4Each individual is responsible for his or her own safety.

Thermo Scientificiv 29 cu ft Environmental Chamber

Preface

Do You Need Information or Assistance on

Thermo Scientific Products?

If you do, please contact us 8:00 a.m. to 6:00 p.m. (Eastern Time) at:

1-740-373-4763 Direct

1-800-438-4851 Toll Free, U.S. and Canada

1-877-213-8051 FAX

http://www.thermoscientific.com Internet Worldwide Web Home Page

service.led.marietta@thermofisher.com Tech Support Email Address

Certified Service Web Page

Thermo Fisher Scientific

401 Millcreek Road, Box 649

Marietta, OH 45750

Our staff can provide information on pricing and give you quotations. We can

take your order and provide delivery information on major equipment items or make

arrangements to have your local sales representative contact you. Our products are listed on the

Internet and we can be contacted through our Internet home page.

Our staff can supply technical information about proper setup, operation or

troubleshooting of your equipment. We can fill your needs for spare or replacement parts or

provide you with on-site service. We can also provide you with a quotation on our Extended

Warranty for your Thermo Scientific products.

Whatever Thermo Scientific products you need or use, we will be happy to discuss your

applications. If you are experiencing technical problems, working together, we will help you

locate the problem and, chances are, correct it yourself...over the telephone without a service

call.

When more extensive service is necessary, we will assist you with direct factory trained

technicians or a qualified service organization for on-the-spot repair. If your service need is

covered by the warranty, we will arrange for the unit to be repaired at our expense and to your

satisfaction.

Regardless of your needs, our professional telephone technicians are available to assist you

Monday through Friday from 8:00 a.m. to 6:00 p.m. Eastern Time. Please contact us by

telephone or fax. If you wish to write, our mailing address is:

International customers, please contact your local Thermo Scientific distributor.

Sales Support

Service Support

www.unitylabservices.com

29 cu ft Environmental Chamber vThermo Scientific

Table of Contents

Installation and Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

Control Panel Keys, Displays & Indicators . . . . . . . . . . . . . . . . . . . .1-2

Keypad Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3

Install the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3

Preliminary Cleaning and Disinfecting . . . . . . . . . . . . . . . . . . . . . .1-4

Install the Shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

Level the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

Connect to Electrical Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

Incubator Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

Set the Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

Set the Overtemp Setpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6

Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

Calibrate the Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

Temperature Stabilization Periods . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

Turn All Audible Alarms On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

Set an Access Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

Set Low Temp Alarm Limit (Tracking Alarm) . . . . . . . . . . . . . . . . . .3-2

Enable Temp Alarms to Trip Relay Contacts . . . . . . . . . . . . . . . . . . .3-2

Communications Address - RS485 . . . . . . . . . . . . . . . . . . . . . . . . . .3-3

Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

Sensor Fault Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

Clean the Glass Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

Replace the Power Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2

Discarding/ Removing Incubator from Service . . . . . . . . . . . . . . . . . .5-3

Section 1

Section 2

Section 3

Section 4

Section 5

vi 29 cu ft Environmental Chamber Thermo Scientific

Factory Installed Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

Connect the Remote Alarm Contacts . . . . . . . . . . . . . . . . . . . . . . . . .6-1

Connect the RS485 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2

Connect the Analog Output Boards . . . . . . . . . . . . . . . . . . . . . . . . .6-2

Inner Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-4

Shaker Support Shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-4

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1

Electrical Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-1

Table of Contents

Section 6

Section 8

Section 7

Section 9

Appendix A

29 cu ft Environmental Chamber 1-1Thermo Scientific

Section 1 Installation and Start-Up

Figure 1-1. Front View

Figure 1-4. Side View

Figure 1-3. Back View

Figure 1-2. Top View

1-2 29 cu ft Environmental Chamber Thermo Scientific

Section 1

Installation and Start-Up

Silence - Silences the audible alarm.

Alarm Indicator - Light pulses on/off during an alarm condition in

the unit.

Mode Select Switch - Used to select Run, Setpoints, Calibration and

System Configuration Modes.

Message Center - Displays system status.

Mode Select Indicators -

• Run: Run Menu

• Set: Set Points Menu

• Cal: Calibrate Menu

• Config:: Configuration Menu

Up and Down Arrows - Increases or decreases the number values,

toggles between choices.

Enter - Stores the value into computer memory.

Heat Indicator - Lights when power is applied to the heaters.

Temp Display – Displays temperature continuously

Scroll for Parameters Arrows - Moves the operator through the choices

of the selected mode.

Control Panel Keys,

Displays & Indicators

Silence Mode System OK 36.9

Enter

Run Set Cal Config

Heat Temp

Scroll for Parameters

Silence

Alarm Indicator

Mode Select

Switch

Message

Center

Mode Select

Indicators

Up and Down

Arrows

Enter

Heat Indicator

Temp Display

Scroll for Parameters

Figure 1-5. Control Panel

29 cu ft Environmental Chamber 1-3Thermo Scientific

Section 1

Installation and Start-Up

Install the Unit

The Model 3960 Series Reach-In Incubator has four basic modes that

allow incubator setup: Run, Setpoints, Calibration and System

Configuration.

• Run is the default mode during normal operation.

• Set is used to enter system setpoints.

• Calibration is used to calibrate various system parameters.

• Configuration allows for custom setup of various options.

The chart below shows the selections under each of the modes.

Scroll for Parameters Arrows: Steps the operator through the parameters

of SET, CAL and CONFIG Modes. The right arrow goes to the next

parameter, the left arrow returns to the previous parameter.

Up Arrow: Increases or toggles the parameter values that have been select-

ed in the SET, CAL, and CONFIG Modes.

Enter: Must press Enter key to save to memory all changed values.

Down Arrow: Decreases or toggles the parameter values that have been

selected in the SET, CAL and CONFIG Modes.

Silence Key: Press to silence the audible alarm. See Section 4 for alarm

ringback times.

Units must be installed against a wall or similar structure. Maintain a three

inch clearance behind the incubator for electrical connections.

Locate the unit on a firm level surface capable of supporting the unit’s

weight of approximately 500 lbs. Position it away from doors and windows

and heating and air conditioning ducts.

Warning This incubator weighs approximately 500 lbs. Have sufficient

personnel available when moving. s

Keypad Operation

RUN SETPOINT CALIBRATION CONFIGURATION

Default Mode Temperature Temp Offset Audible

Overtemp Access Code

Temp Lo Alarm

Temp Relay

RS485 Address

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Thermo Scientific Équipement de laboratoire

Thermo Scientific

Thermo Scientific Multidrop Combi+ Manuel utilisateur

Thermo Scientific

Thermo Scientific KingFisher Duo Manuel utilisateur

Thermo Scientific

Thermo Scientific Invitrogen E-Gel G8100 Manuel utilisateur

Thermo Scientific

Thermo Scientific SPD131DDA Manuel utilisateur

Thermo Scientific

Thermo Scientific Thermo Scientific SL16 Manuel utilisateur

Thermo Scientific

Thermo Scientific Finnpipette Manuel utilisateur

Thermo Scientific

Thermo Scientific SmartView SV100A Manuel utilisateur

Thermo Scientific

Thermo Scientific Thermo Scientific 494 Series Manuel utilisateur

Thermo Scientific

Thermo Scientific Heraeus Multifuge X1 Manuel utilisateur

Thermo Scientific

Thermo Scientific STANDARD Series Manuel utilisateur

Thermo Scientific

Thermo Scientific Thermo Scientific SL Plus Series Manuel utilisateur

Thermo Scientific

Thermo Scientific HPS RT2 Advanced Manuel utilisateur

Thermo Scientific

Thermo Scientific Dionex UltiMate 3000 Series Manuel utilisateur

Thermo Scientific

Thermo Scientific M79700 Manuel utilisateur

Thermo Scientific

Thermo Scientific 500 Manuel utilisateur

Thermo Scientific

Thermo Scientific 88870001 Manuel utilisateur

Thermo Scientific

Thermo Scientific PrintMate A79510100 Manuel

Thermo Scientific

Thermo Scientific Applied Biosystems GeneChip 645 Manuel utilisateur

Thermo Scientific

Thermo Scientific HM525 NX Series Manuel

Thermo Scientific

Thermo Scientific 3767A Manuel utilisateur

Thermo Scientific

Thermo Scientific RC 12BP Plus Manuel utilisateur

Thermo Scientific

Thermo Scientific Sorvall T3 Manuel utilisateur

Thermo Scientific

Thermo Scientific Sorvall LYNX 4000 Manuel utilisateur

Thermo Scientific

Thermo Scientific Jewett XR60C Manuel utilisateur

Manuels Équipement de laboratoire populaires d'autres marques

Qiagen

Qiagen DML 3000 Manuel utilisateur

Queensgate

Queensgate NANOSCAN OP400 Manuel de programmation

Conviron

Conviron GEN1000-GE Manuel utilisateur

Parr Instrument

Parr Instrument 4560 Mode d’emploi

IKA

IKA IC control Manuel utilisateur

Integra

Integra DOSE IT Manuel utilisateur

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuel utilisateur

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuel utilisateur

NI PXI-5422 Manuel

Collomix

Collomix Aqix Manuel utilisateur

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuel utilisateur

Ocean Insight

Ocean Insight FLAME-NIR+ Manuel utilisateur

Parker

Parker ALIGN-MG-NA Manuel utilisateur

BD 644787 Manuel utilisateur

DENTAURUM

DENTAURUM Compact Megaplus Manuel utilisateur

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuel utilisateur

VWR

VWR SAS Super IAQ Manuel utilisateur

illumina

illumina MiSeqDx Manuel utilisateur